Download Print this page

Hanskamp PipeFeeder DumpUnit Assembly, Installation And Operation Instructions

Carousel feeding system

Advertisement

Quick Links

PipeFeeder DumpUnit
011-165-100
Carrousel voersysteem
Carousel feeding system
Karussell-Fütterungssystem
Système d'alimentation sur roto
EN
Installation and Operation Instructions
Article number: 010-374-000
Date: December 2024
Doetinchem,
Version 1.2 - Translation of original Installation and Operation Instructions
The Netherlands
According to Annex 1 Chapter 1.7.4 of the Machinery Directive 2006/42/EC
www.hanskamp.com

Advertisement

loading
Need help?

Need help?

Do you have a question about the PipeFeeder DumpUnit and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Hanskamp PipeFeeder DumpUnit

  • Page 1 PipeFeeder DumpUnit 011-165-100 Carrousel voersysteem Carousel feeding system Karussell-Fütterungssystem Système d’alimentation sur roto Installation and Operation Instructions Article number: 010-374-000 Date: December 2024 Doetinchem, Version 1.2 - Translation of original Installation and Operation Instructions The Netherlands According to Annex 1 Chapter 1.7.4 of the Machinery Directive 2006/42/EC...
  • Page 2 Please consult your local milking equipment dealer if you do not understand the infor- mation in this manual, or if you need additional information. All information in this manual has been compiled with the greatest care. Hanskamp shall not be liable for errors or faults in this manual. The recommendations made are meant to serve as guidelines.
  • Page 3 The benefit? Faster milking with significantly less feeding of concentrate. Hanskamp's DumpUnit is supplied with 1 limit switch as standard. The switch enables the DumpUnit to release the feed at exactly the right time.
  • Page 4: Signal Words

    Do not modify the equipment in any way. Unauthorized modification may impair the function and/or safety and could affect the life of the equipment, and persons. • Only use approved parts, and make sure they are only installed by authorized tech- nicians. 4 - 19 Hanskamp AgroTech BV (The Netherlands) www.hanskamp.com...
  • Page 5 Before connecting the DumpUnit to the power supply, make sure that all parts are properly tightened and that all cables and mountings are in good condition. • If you have any other questions, please contact your milking technology dealer. 5 - 19 Hanskamp AgroTech BV (The Netherlands) www.hanskamp.com...
  • Page 6 This chapter lists the general safety messages. Specific safety messages, where potential hazards may arise if the procedures or instructions are not followed, are included in the appropriate sections of this manual. 6 - 19 Hanskamp AgroTech BV (The Netherlands) www.hanskamp.com...
  • Page 7 Installation and Operating Instructions General description The Hanskamp DumpUnit is an electrically operated dosing flap developed to dispense concentrate pellets in a rotary milking parlour (fig. 1). The DumpUnit is filled by 1 or more HighSpeed PipeFeeders. The PipeFeeders can be connected to the feeding computer or to Hanskamp's SmartPanel system, which also allows stand-alone feeding.
  • Page 8 Do not use solvents or abrasives that could damage safety stickers. • Replace missing or illegible safety stickers. Safety stickers are available from Hanskamp. Always use the product numbers in corre- spondence. 8 - 19 Hanskamp AgroTech BV (The Netherlands)
  • Page 9 (flap) in the down pipe (fig. 6). Danger! Always install a down pipe of at least 85 cm long or use other measures 001-955-000 to prevent the risk of cutting. 011-163-000 9 - 19 Hanskamp AgroTech BV (The Netherlands) www.hanskamp.com...
  • Page 10 3/4 of the height of the pipe, so that it forms a solid whole. Be sure to fix the PipeFeeders in a vertical position using a spirit level when tightening the clamps. Plastic part is rotatable 10 - 19 Hanskamp AgroTech BV (The Netherlands) www.hanskamp.com...
  • Page 11 The entire supply in the down pipe will then be released into the feed trough at once. If 24 V AC/DC is not available, you can order the Hanskamp PowerUnit 24 V DC 10A with power boost (art. no. 002-812-000). The corresponding connection diagram is shown below.
  • Page 12 Maintenance Check the PipeFeeder DumpUnit installation daily for faults and wear. Do this by means of a control test on the feed motors, using the limit switch. Make sure that possible operating noises and vibrations caused by the PipeFeeder are reduced or eliminated as much as possible.
  • Page 13 No part of this publication may be reproduced or made public without the prior written consent of Hanskamp Ag roTech BV. Although this publication has been compiled with the greatest care, Hanskamp AgroTech BV is not liable for any damage that may arise due to any errors or omis- sions it might contain.
  • Page 14 NEN-EN-ISO 12100 NEN-EN-IEC 60204-1 NEN-EN-ISO 13857 If the PipeFeeder DumpUnit is not connected and the prescribed safety instructions are not used, this Declaration of Conformity is not applicable and no rights can be derived from this declaration. Doetinchem, the Netherlands, 01-04-2022 H.J.
  • Page 15: Extra Options

    MotorController Hanskamp controller between HighSpeed motor and feed computer. Helps the mo- tor start up and slow down for extra accuracy. Equipped with a replaceable motor fuse. Available for one (art. no. 002-816-000), two (art. no 002-817-000), three (art.
  • Page 16 DumpUnit Carrousel voersysteem - Carousel feeding system - Karussell-Fütterungssystem - Système d’alimentation sur roto Individual parts PipeFeeder DumpUnit storage container (011-165-000) For maintenance or other purposes, individual parts can be reordered through your milking equipment dealer. When doing so, please refer to the article numbers as indicated in the drawing below.
  • Page 17 011-155-000 Dosing flap, stainless steel, for Dump HighSpeed 011-159-000 Shaft, Ø 10 mm, with gear, for Dump HighSpeed Description of parts - PipeFeeder DumpUnit incl. mounting bracket (additional parts) Article number Description Quantity 011-261-000 Spacer, 4 mm, sendzimir, for bracket PipeFeeder Dump...
  • Page 18 Long 1894 mm 3577 mm Height PipeFeeder Short See table for other lengths Length supplied tube Height DumpUnit with storage container Maximum width Length of supplied PVC down pipe, Ø 125 18 - 19 Hanskamp AgroTech BV (The Netherlands) www.hanskamp.com...
  • Page 19 Carrousel voersysteem - Carousel feeding system - Karussell-Fütterungssystem - Système d’alimentation sur roto Hanskamp AgroTech BV Broekstraat 17 7009 ZB Doetinchem Also take a look at: The Netherlands Tel: +31 (0)314 - 393 797 Fax: +31 (0)314 - 393 826 info@hanskamp.nl www.hanskamp.com 19 - 19 Hanskamp AgroTech BV (The Netherlands) www.hanskamp.com...

This manual is also suitable for:

011-165-100010-374-000