Subscribe to Our Youtube Channel
Related Manuals for Flybox Eclipse NG
Summary of Contents for Flybox Eclipse NG
- Page 1 Eclipse NG Electronic Flight Instrument System Installation Manual Mechanical and Electrical Installation for Eclipse NG - IFIS version Revision 11...
- Page 2 1. Mechanical Dimensions Mechanical and Electrical Installation for Eclipse NG - IFIS version Revision 11...
-
Page 3: Panel Cutout
Avoid placing in hot locations (for example near heater vents). • Find a location where the display will always be completely visible. • Mechanical and Electrical Installation for Eclipse NG - IFIS version Revision 11... - Page 4 - Insert an appropriate circuit breaker to the positive main supply, considering the current requirement for the sensor powered by the Eclipse and considering that the instrument only current supply is 0.5 A. - Use aeronautic cable for the wiring. Mechanical and Electrical Installation for Eclipse NG - IFIS version Revision 11...
- Page 5 Pin#15 of CON1 connector. So, for example, +Power out for sensors supply”, including if you sink 500mA on a single pin, no more current can be supplied on the other pins. Mechanical and Electrical Installation for Eclipse NG - IFIS version Revision 11...
- Page 6 CON1 connections Mechanical and Electrical Installation for Eclipse NG - IFIS version Revision 11...
- Page 7 Range: 5-30Vpp; frequency range 2Hz-10Khz, Right Gear down Digital input 3 min. pulse duration: 50uS indicator Alarm Out 2 NPN, 500 mA MAX +Power out for sensors supply 500 mA * Mechanical and Electrical Installation for Eclipse NG - IFIS version Revision 11...
- Page 8 Pin#15 of CON1 connector. So, for +Power out for sensors supply”, including example, if you sink 500mA on a single pin, no more current can be supplied on the other pins. CON2 connections Mechanical and Electrical Installation for Eclipse NG - IFIS version Revision 11...
- Page 9 CON2 connections Mechanical and Electrical Installation for Eclipse NG - IFIS version Revision 11...
- Page 10 CON2 connections Mechanical and Electrical Installation for Eclipse NG - IFIS version Revision 11...
- Page 11 CON2 connections Mechanical and Electrical Installation for Eclipse NG - IFIS version Revision 11...
- Page 12 CON2 connections Mechanical and Electrical Installation for Eclipse NG - IFIS version Revision 11...
- Page 13 CON2 connections Mechanical and Electrical Installation for Eclipse NG - IFIS version Revision 11...
- Page 14 CON2 connections Mechanical and Electrical Installation for Eclipse NG - IFIS version Revision 11...
- Page 15 25-pin d-sub receptacle, view from wiring side NOTE1: If a Resistive Probe is used, connect to GND or preferably directly on the engine block where the probes are installed Mechanical and Electrical Installation for Eclipse NG - IFIS version Revision 11...
- Page 16 If a Resistive Probe is used, connect to GND or preferably directly on the engine block where the probes are installed. NOTE2: Input voltage range is 0-2.5V. If the transducer output voltage is higher than 2.5V, add a resistive divider to adjust the voltage. Mechanical and Electrical Installation for Eclipse NG - IFIS version Revision 11...
- Page 17 CON3 connections Mechanical and Electrical Installation for Eclipse NG - IFIS version Revision 11...
- Page 18 WARNING: All photos, data, drawings, instruments layouts, technical solutions and data representation you find in this document or watching at Flybox® instruments working and/or you can access by means of any other media, including web sites, are sole property of MICROEL SRL, cannot be copied or imitate without a written permission of MICROEL SRL itself and are protected by law, even by means of extended international copyright and/or specific patents deposited.
Need help?
Do you have a question about the Eclipse NG and is the answer not in the manual?
Questions and answers