Download
Share
Print this page
  1. Manuals
  2. Brands
  3. AJ Aircraft Manuals
  4. Toy
  5. Laser 230z
  6. Assembly & instruction manual

AJ Aircraft TA Horizons Laser 230Z Assembly & Instruction Manual

Hide thumbs Also See for TA Horizons Laser 230Z:

Advertisement

Quick Links

Download this manual
TA HORIZONS 37'' LASER 230Z
ASSEMBLY INSTRUCTION MANUAL
Technical Data-
Wingspan : 37"
Length
AUW : 310-340g
(Depends upon the setup used)
EPP CONSTRUCTION
R
Setup Recommendations (Not Included)-
Motor : 25-40G 1100-1500KV Outrunner
ESC
: 38"
Servos
Propeller : 9-10" electric
Battery
(T-Motor AM40 Recommended for Super Light Setup)
: 20 amp
: 4Pcs 9gms each
: 850-1000Mah 3S Lipo
KIT ONL Y
Page 1

Advertisement

loading
Need help?

Need help?

Do you have a question about the TA Horizons Laser 230Z and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for AJ Aircraft TA Horizons Laser 230Z

Summary of Contents for AJ Aircraft TA Horizons Laser 230Z

  • Page 1 TA HORIZONS 37’’ LASER 230Z ASSEMBLY INSTRUCTION MANUAL Technical Data- Setup Recommendations (Not Included)- Motor : 25-40G 1100-1500KV Outrunner Wingspan : 37" (T-Motor AM40 Recommended for Super Light Setup) : 20 amp Length : 38” Servos : 4Pcs 9gms each Propeller : 9-10”...
  • Page 2 WARNING INFORMATION & SAFETY INSTRUCTIONS Website: www.tahorizons.com Email: tahorizons@gmail.com Thank you for choosing TA Horizons. Please read the entire manual thoroughly before you begin to assemble this model. If you have any questions, please contact us aforementioned email address. This R/C airplane is not a toy! Read and understand the entire manual before assembly.

  • Page 3: Kit Contents

    Kit Contents 1. EPP Parts EPP Parts Fuselage Wings Horizontal stabilizer Horizontal profile sections Landing gear cover Side Force Generators X 2 Wheel Pants X 2 Wing Truss Supports X 2 2. Hardware / Small Parts Hardware Parts Polycarbonate parts Fuselage assembly jig EPP Wheels X 2 150mm velcro...
  • Page 4 TOOLS AND BUILDING MATERIAL REQUIRED • Needle Nose Pliers • Heat Gun • Wire Cutters • Tape Measure and Ruler • Low Temp Hot Glue Gun • Black Sewing Thread • Scissors • High Viscosity CA • Small Phillips Screw Driver •...
  • Page 5 The Build Please Note: Few pictures shown below are of different plane and for reference purpose only. 1. Building surface should be at least 2ft x 4ft and flat, Use a (This is mandatory step) locate the hinged items as shown wax paper over the surface to avoid sticking EPP on it when above, Bend them back on to each other as shown and let set gluing.
  • Page 6 The Build Please Note: Few pictures shown below are of different plane and for reference purpose only. ACTIVATOR GEL GLUE(HV) Glue it in the pre-cut groove. Use a spray activator (Kicker) to 8. Apply a thin layer on gluing surface. cure.
  • Page 7 The Build Please Note: Few pictures shown below are of different plane and for reference purpose only. GEL GLUE(HV) 13. Locate the above 3 strips measuring 500mm L X 2 and 14. Apply a thin layer of HV CA to the mating surfaces of the 200mm L X 1, these are going to be used for reinforcing lower vertical fuselage.
  • Page 8 The Build Please Note: Few pictures shown below are of different plane and for reference purpose only. 19. Optionally use a heat shrink tubing for better cosmetic 20. Glue the shown parts over the pre cut slots, for landing gear finish.
  • Page 9 The Build Please Note: Few pictures shown below are of different plane and for reference purpose only. GLUE HERE 25. Make sure the lower part of fuselage is straight while 26. Install the wheel over the shaft, make sure it is spinning installing the gears using the building jig.
  • Page 10 The Build Please Note: Few pictures shown below are of different plane and for reference purpose only. 150mm RODS Locate the wing truss support, glue it in pre-cut slot like 32. Rods bracing the fuselage are 1mm dia 150mm L. shown in the picture.
  • Page 11 The Build Please Note: Few pictures shown below are of different plane and for reference purpose only. AILERONS RUDDER ELEVATOR 37. Locate the servo trays and control horns, Please refer to 38. Glue the aileron servo tray shown in the image over the above image for selecting control horn for specific control precut servo slot using HV CA.
  • Page 12 The Build Please Note: Few pictures shown below are of different plane and for reference purpose only. 43. Locate all the control horns and servo arms for next 44. Locate 8 X Quick links ans 8 X 2mm screws. process. THIN CA 45.
  • Page 13 The Build Please Note: Few pictures shown below are of different plane and for reference purpose only. Glue Here 49. Locate the 140mm aileron control rod, glue it on the one 50. Use the assembly jig to center the ailerons and align it with side (Servo arm), using thin CA or optionally HV CA.
  • Page 14 The Build Please Note: Few pictures shown below are of different plane and for reference purpose only. Glue Here 55. Locate the 500mm control rod, Notice how the rod is slid in 56. Glue the Elevator control rod on the one side (Servo arm), the pre glued pushrod guides, shown in the above image.
  • Page 15 The Build Please Note: Few pictures shown below are of different plane and for reference purpose only. GEL GLUE(HV) 61. Go Slow, once again it is so important to keep this as 62. Now with the top portion installed glue the rear part to the flat straight as possible.
  • Page 16 The Build Please Note: Few pictures shown below are of different plane and for reference purpose only. 67. Here is another view. 68. Glue the last remaining 5X0.5mm 230mm L Flat strip over the trailing edge of rudder. 69. Shown above is the motor mount glued, making sure 70.
  • Page 17 The Build Please Note: Few pictures shown below are of different plane and for reference purpose only. 73. The long piece of velcro along with the strapping velcro If desired, locate these smaller side force generators that will mounted, above is the location of the battery for this setup. be glued into the counterbalances of the ailerons.
  • Page 18 Thank You T hank You.. Thank you for your purchase at TA Horizons. We sincerely hope that our products can provide the same thrill to you that we experience in this hobby. The motive of this project is to spread the outcome of my love for teaching and share my knowledge and experience with every enthusiast out there.