Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for PowerPac PPBL300A
Summary of Contents for PowerPac PPBL300A
- Page 1 Model: PPBL300A 2 4 0 0 6 1 - 2 4...
- Page 2 PARTS & DESCRIPTION (Measuring Cup) Blender Jug Blender Blade Blender Blade assembly Motor unit ON/OFF & Speed Rotary Knob Base Non-slip Feet Grinder Cup Grinder Blade Grinder Blade assembly...
- Page 3 WARNINGS ATTENTION : Read this booklet carefully as it contains important instructions for a safe installation, use and maintenance. Important instructions to be kept for future reference. The following basic precautions should always be followed when using electrical appliances: Read all instructions before using the appliance. The Appliance This appliance must be used only for the purpose it was expressly designed;...
-
Page 4: Operation
Operation If you are using the appliance for the first time, you should: Clean the exterior of the Motor unit with a damp cloth. Use a little detergent, if necessary, and wipe dry. The Motor unit may NOT be immersed in water. Wash the Cap, Lid, Blender Jug &... - Page 5 • rotate the ON/OFF & Speed Rotary Knob too forcefully so as to avoid any damage; • detach the Blender Jug or Grinder Cup while the appliance is in operation; • leave the appliance unsupervised during operation. During operation, DO NOT touch the appliance with wet body parts, and it is recommended to have between you and the standing surface, an isolating element (for example, wearing shoes with rubber soles).
-
Page 6: How To Use
HOW TO USE Clean the Motor unit and accessories before using. Refer to the section “How to clean and maintain” immediately following this section. Place the Base of the Motor unit on a flat, dry and heat-resistant surface. The Blender Attach the Blender Blade assembly to the Blender Jug by turning it anti-clockwise until it is securely (but NOT overly) tightened to the Blender Jug. - Page 7 only if a Jam occurs: DO NOT continue blending if the blade is jammed. Set the ON/OFF & Speed Rotary Knob to ‘0’ (OFF). Switch the wall switch off and unplug the power cable. Wait for the blades to stop turning. Detach the Lid from the Blender Jug by turning it anti-clockwise.
- Page 8 only if a Jam occurs: DO NOT continue blending if the blade is jammed. Set the ON/OFF & Speed Rotary Knob to ‘0’ (OFF). Switch the wall switch off and unplug the power cable. Wait for the blades to stop turning. Rotate slightly for the Grinder Blade assembly to unlock from the Motor unit and detach Lift the Grinder Cup out of the Motor unit.
-
Page 9: How To Clean And Maintain
HOW TO CLEAN AND MAINTAIN On the completion of blending, grinding or mincing, rotate the ON/OFF & Speed Rotary Knob to ‘0’ (OFF), switch the wall switch off and unplug the power cable. Before cleaning, please make sure the blades have stopped running. Clean the Motor unit with a damp cloth. -
Page 10: Problem Solving
PROBLEM SOLVING Fault symptom Cause analysis Troubleshooting After the Blender Jug or Safety lock is not connected Reconnect the Motor unit and the Grinder Cup installed, the Blender Jug or Grinder Cup appliance does not work after pressing the switch The motor is damaged or Turn the motor shaft. -
Page 11: Specification
SPECIFICATION PPBL300A MODEL 220-240V~ RATED VOLTAGE 50/60 Hz FREQUENCY 400W POWER 1.5L CAPACITY... -
Page 12: Warranty
However, if the customer still requests that the defective appliance be repaired, PowerPac Electrical Pte Ltd may, at its discretion, repair the appliance but impose a labour charge, as well as the costs of the replacement parts, to be borne solely by the customer.
Need help?
Do you have a question about the PPBL300A and is the answer not in the manual?
Questions and answers