PARTS & DESCRIPTION (Measuring Cup) Blender Jug Blender Blade Blender Blade assembly Motor unit ON/OFF & Speed Rotary Knob Ice Button Base Non-slip Feet Chopper Cup Cover Chopper Cup Chopper Blade Chopper Blade assembly Grinder Cup Grinder Blade Grinder Blade assembly...
Page 3
WARNINGS ATTENTION : Read this booklet carefully as it contains important instructions for a safe installation, use and maintenance. Important instructions to be kept for future reference. The following basic precautions should always be followed when using electrical appliances: Read all instructions before using the appliance. The Appliance This appliance must be used only for the purpose it was expressly designed;...
DO NOT use or store the appliance outdoors. Store and use the appliance only indoors, or in any case, protected from weathering such as rain, direct radiation of the sun and dust. Operation If you are using the appliance for the first time, you should: Clean the exterior of the Motor unit with a damp cloth.
Page 5
• overload the Blender Jug, Grinder Cup or Chopping Cup by overfilling it. This is generally below ¾ of the total volume of the container as especially during blending, liquids will churn and may spill out of the container. The jug should contain cut fruits and vegetables NO larger than 1 inch (2.5 cm) in length and thickness and must NOT contain dry food (food with insufficient amount of water, very hard ingredients (such as coffee beans, soybeans, rice, ice cubes or frozen foods), or foods or liquids with a temperature greater...
HOW TO USE Clean the Motor unit and accessories before using. Refer to the section “How to clean and maintain” immediately following this section. Place the Base of the Motor unit on a flat, dry and heat-resistant surface. The Blender Place the Sealing Ring on the inner edge of the Blender Blade assembly (if not attached).
Page 7
Crushing Ice Before using the Blender to crush ice, make sure it is clean and rinse it out thoroughly. Ice cubes come in many shapes and sizes. Insert a maximum of 12 ice cubes and add 60 ml of cold water. DO NOT be tempted to increase the number of ice cubes and blend for longer – this will not work.
Page 8
Wait for the blades to stop turning. ① Turn the Grinder Cup (with the Grinder Blade assembly) anti-clockwise until it detaches from the Motor unit. ② Lift the Grinder Cup out of the Motor unit. Invert the Grinder Cup with the Grinder Blade assembly, ① turn the Grinder Blade assembly clockwise from the Grinder Cup and ②...
Page 9
The Chopper If need be, separate the Chopper Blade assembly from the Chopper Cup. Place the Sealing Ring on the inner edge of the Chopper Blade assembly (if not attached). Likewise, to attach the Chopper Blade assembly to the Chopper Cup, perform the following operations: With the mouth of the Chopper Cup facing upwards, place food ingredients into the Chopper Cup.
HOW TO CLEAN AND MAINTAIN On the completion of blending, grinding, mincing or chopping, rotate the ON/OFF & Speed Rotary Knob to ‘0’ (OFF), switch the wall switch off and unplug the power cable. Before cleaning, please make sure the blades have stopped running. Clean the Motor unit with a damp cloth.
PROBLEM SOLVING Fault symptom Cause analysis Troubleshooting After the Blender Jug, Safety lock is not connected Reconnect the Motor unit and the Grinder Cup or Chopper Blender Jug, Grinder Cup or Cup is installed, the Chopper Cup appliance does not work The motor is damaged or Turn the motor shaft.
However, if the customer still requests that the defective appliance be repaired, PowerPac Electrical Pte Ltd may, at its discretion, repair the appliance but impose a labour charge, as well as the costs of the replacement parts, to be borne solely by the customer.
Page 15
In accordance with the terms and conditions of this limited warranty as stated below, PowerPac Electrical Pte Ltd, at its expense shall provide free services for the appliance within the warranty period from its date of purchase from our Authorised dealers.
Need help?
Do you have a question about the PPBL200A and is the answer not in the manual?
Questions and answers