Page 2
Serial number: _____________________________ Date of purchase: ___________________________ Place of purchase: __________________________ Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies' product names or trademarks are used herein for identification purposes only and belong to their respective companies.
Information for your safety and comfort Safety instructions Read these instructions carefully. Keep this document for future reference. Follow all warnings and instructions marked on the product. Special notes on LCD monitors The following are normal with the LCD monitor and do not indicate a problem. •...
Safe listening To protect your hearing, follow these instructions. • Gradually increase the volume until you can hear it clearly and comfortably and without distortion. • After setting the volume level, do not increase it after your ears have adjusted. •...
Warning! The grounding pin is a safety feature. Using a power outlet that is not properly grounded may result in electric shock and/or injury. Note: The grounding pin also provides good protection from unexpected noise produced by other nearby electrical devices that may interfere with the performance of this product.
We at Acer are very conscious of the environmental effects of our business and strive to identify and provide the best working procedures to reduce the environmental impact of our products.
Tips and information for comfortable use Computer users may complain of eyestrain and headaches after prolonged use. Users are also at risk of physical injury after long hours of working in front of a computer. Long work periods, bad posture, poor work habits, stress, inadequate working conditions, personal health and other factors greatly increase the risk of physical injury.
Display • Keep your display clean. • Keep your head at a higher level than the top edge of the display so your eyes point downward when looking at the middle of the display. • Adjust the display brightness and/or contrast to a comfortable level for enhanced text readability and graphics clarity.
Page 9
(“x” = 0~9, a ~ z, A ~ Z, or blank) We, Acer Incorporated, hereby declare under our sole responsibility that the product described above is in conformity with the relevant Union harmonization legislations as below Directive and following harmonized...
Page 10
Federal Communications Commission Supplier's Declaration of Conformity Acer America Corporation 1730 N First St Suite 400, San Jose, CA 95112 408) 533-7700 Tel : ( (408) 533-4555 Fax : Federal Communications Commission Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the...
ENERGY STAR® Acer’s ENERGY STAR qualified products save you money by reducing energy costs and helps protect the environment without sacrificing features or performance. Acer is proud to offer our customers products with the ENERGY STAR mark. What is ENERGY STAR?
Page 12
TCO Certified A third-party certification according to ISO 14024 Toward sustainable IT products Say hello to a more sustainable product IT products are associated with a wide range of sustainability risks throughout their life cycle. Human rights violations are common in the factories.
Page 13
Service for product life extension is available in limited countries, please refer to local Acer website or contact local Acer representatives for details. Service for packaging take back program is free of charge and available in limited countries, please refer to local Acer website or contact local Acer representatives for details.
Page 14
Information for your safety and comfort Safety instructions Special notes on LCD monitors Cleaning your monitor Connecting/disconnecting the device Accessibility Safe listening Warnings Using electrical power Product servicing Potentially explosive environments Additional safety information IT Equipment Recycling Information Disposal instructions Recycling Information for the United States of America LCD pixel statement Tips and information for comfortable use...
Page 15
LCD monitor Quick start guide Product Information for EU Energy https://www.acer.com M U . X X X X X . X X X 9 0 1 1 1 - X X X X X...
Attaching/removing the base Installation: Align the base with the stand and push the base towards the top of the monitor, and then rotate the base clockwise. Tighten the screw clockwise. Remove: Reverse the steps to remove the base. Note: Take care when performing the installation to avoid injuring yourself. If installing with a wall mounting kit, it is recommended to use VESA mounting kit (100 x 100) with M4 x 12(L) mm screws to fix your monitor on the wall.
Screen position adjustment In order to optimize the best viewing position, you can adjust the height/tilt/swivel/Pivot of the monitor. • Height Adjustment After pressing the top of the monitor then you can adjust the height of the monitor. 150mm • Tilt Please see the illustration below for an example of the tilt range.
Page 18
• Swivel With the built-in pedestal, you can swivel the monitor for the most comfortable viewing angle. • Monitor Pivot Before rotating the display,lift it to the top position and then push it back to the utmost degree. Rotate clockwise or counter-clockwise until the monitor stops at ±90°.
Connecting the power cord • Check first to make sure that the power cord you use is the correct type required for your area. • The monitor has a universal power supply that allows operation in either 100/120 V AC or 220/240 V AC voltage area.
Display Data Channel (DDC) To make installation easier, so long as your system supports the DDC protocol, the monitor is able to plug-and-play. The DDC is a communication protocol through which the monitor automatically informs the host system about its capabilities; for example, supported resolutions and corresponding timing.
Installation To install the monitor on your host system, please follow the steps below: 1. Turn off your computer and unplug your computer's power cord. 2. Connect the signal cable to the DP (optional) and/or HDMI (optional) input socket of the monitor, and the DP (optional) and/or HDMI (optional) output socket of the graphics card on the computer.
Page 24
Battery and remote control instructions Inserting batteries Before using the TV set for the first time, insert two “AAA” batteries. When the batteries are low, Inserting batteries Inserting batteries Inserting batteries and the remote control does not work, replace with new “AAA” batteries. Before using the TV set for the first time, insert two “AAA”...
Page 25
WW remote control WW Remote control 1. POWER (power standby / turn on) Turn on and turn off the power 2. BLUE LIGHT+/- Adjusting the Blue light setting 3. BRI +/- Adjusting the Brightness setting 4. INFO Show up the basic information for current input. 5.
User controls External controls Power Turns the monitor on/off. Blue indicates power on. Amber indicates standby/ button power saving mode. a. Press to view Main page.Press again to enter next function in the Function Menu. b. Press this button to select the desired item when in OSD menu. a.
Using the Shortcut Menu Note: The following content is for general reference only. Actual product specifications may vary. The OSD (onscreen display) can be used to adjust the settings of your LCD monitor. Press the MENU key to open the OSD. You can use the OSD to adjust the picture quality and general settings.
Page 28
Adjusting the Performance setting 2560 x 1440 Standard HDMI 1 Resolution Mode Input AdaptiveSync Over Drive Performance Adap�veSync Picture Color Refresh Rate Num Audio System Informa�on Save Se�ngs to ... 1. Press the key to bring up the OSD. 2. Using the keys, select Performance from the OSD menu.
Page 29
8. ACM: Turn ACM on or off. Note: Set to "On", will be based on the current screen to dynamic contrast adjustment. 9. HDR: MNT will automatically determine whether the signal source is HDR, Ex PC HDR, if it is in HDR format, the HDR function of Monitor can be turned on and the effect of Auto / Off can be selected.
Page 30
4. The Color menu can be used to adjust the current Modes,sRGB, Gamma, Color Temp, Grayscale Mode, 6-Axis Hue, 6-Axis Saturate. 5. Modes: To choose scenario mode. 6. sRGB: Default is off. You can turn sRGB on or off to better color match with peripheral devices, such as printers and digital cameras.
Page 31
you wish to adjust. 3. Use the keys to adjust the sliding scales. 4. The Setting menu can be used to adjust the screen Menu Language, OSD Timeout, Transparency and OSD Lock. 5. Language: Set the OSD menu language. 6. OSD Timeout: Adjust the delay before turning off the OSD menu. 7.
Page 32
3. Use the keys to adjust the sliding scales. 4. The System menu can be used to adjust the Input, Auto Source, Wide Mode, Hot Key Assignment, DDC/CI, HDMI Black Level, Quick Start Mode. 5. Input: Select the source from HDMI 1, HDMI 2, DP. 6.
Save Setting to…(User mode only) Standard 2560 x 1440 HDMI 1 Resolution Mode Input AdaptiveSync Mode: sRGB Performance Mode: Reading Picture Mode: Darkroom Color Audio System Informa�on Save Se�ngs to… 1. Press the key to bring up the OSD. 2. Using the keys, select "Save Setting to..."...
Note: Acer monitor is purposed for video and visual display of information obtained from electronic devices. Product Information for EU Energy Label Regulatory Compliance...
Need help?
Do you have a question about the Vero CB322QU and is the answer not in the manual?
Questions and answers