Page 1
IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Digital copies of all IntelliVibe manuals can be found at www.pentair.com, or by scanning the provided QR code. Se pueden encontrar copias digitales de todos los manuales de IntelliVibe en www.pentair.com, o escaneando el código QR proporcionado.
It is important to comply with these codes, many of which directly regulate the installation and use of this product. Consult your local building and health codes for more information. INTELLIVIBE™ Poo/Spa Light Controller Installation and User Guide...
Page 3
: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. INTELLIVIBE™ Pool/Spa Light Controller Installation and User Guide...
Pairing Controller to the Pentair Pool App Zone Configuration OPERATION ............Button Functions and LED Behavior Controller Dashboard Color Modes (Single Color) Color Modes (Color Shows) Creating Schedules Vacation Mode Energy Saving Mode INTELLIVIBE™ Poo/Spa Light Controller Installation and User Guide...
3. IntelliCenter Pool Control System: An IntelliCenter control system is required to install and operate an IntelliVibe controller. Before IntelliVibe can be added to a Pentair Pool app account, it must first detect an IntelliCenter on the same account.
INSTALLATION This section describes IntelliVibe Controller installation and wiring. For specific light installation and wiring instructions, refer to the appropriate light installation manual(s). RISK OF ELECTRIC SHOCK, WHICH CAN RESULT IN SERIOUS INJURY OR DEATH. Before attempting installation or service, ensure that all power to the circuit is disconnected at the main breaker panel.
2. Place the controller onto the Mounting Bracket (1). 3. Push the Locking Wedge (2) downwards until it clicks into place. The FIGURE 1 locking wedge secures the controller to the mounting bracket. INTELLIVIBE™ Pool/Spa Light Controller Installation and User Guide...
6. Connect power to the Main Power Terminal (4) according to FIGURE 3. TABLE 2 MAIN WIRE MAXIMUM BREAKER SIZE DISTANCE PS300 PANEL TRANSFORMER 12 AWG 15 ft. 120 VAC 50/60 Hz 10 AWG 25 ft 14 VAC 50/60 Hz FIGURE 3 INTELLIVIBE™ Poo/Spa Light Controller Installation and User Guide...
Page 9
100 Watts Maximum per Output 200 Watts Maximum Across All Outputs OUTPUT TERMINAL WIRING Micro JUNCTION BOX JUNCTION BOX JUNCTION BOX (Output 2) (Output 3) (Output 4) JUNCTION BOX (Output 1) Mezzo FIGURE 4 INTELLIVIBE™ Pool/Spa Light Controller Installation and User Guide...
ZONE CONFIGURATION A Zone is a group of lights from one or more controller outputs that will react in unison to a command given in the Pentair Pool app. Tap the Settings icon ( ) in the top-right corner of any Color Mode screen.
Refer to TABLE 5 to determine FACTORY RESET* Yellow (16+ Seconds) what specific LED behaviors indicate. *Note: After a factory reset, IntelliVibe must be removed your smartphone's connected devices list, then re-paired. TABLE 5 COLOR BEHAVIOR INDICATES SOLID Controller is operating normally.
10. PRESET COLOR Buttons: Tap a color to activate a default preset setting. 11. SCHEDULE Button: Tap to create a weekly or one-time zone schedule. Refer to Creating Schedules, page 13 for specific instructions. COLOR SETTINGS WHITE SETTINGS INTELLIVIBE™ Poo/Spa Light Controller Installation and User Guide...
• Lava Flow: Transition through red, orange, and yellow 5. BRIGHTNESS Slider: Set brightness level. 6. SCHEDULE Button: Tap to create a weekly or one-time zone schedule. COLOR SHOW SETTINGS Refer to Creating Schedules, page 13 for specific instructions. INTELLIVIBE™ Pool/Spa Light Controller Installation and User Guide...
Energy Saving Mode will automatically turn off the lights after a set number of hours, as long as there are no active overriding schedules. The Pentair Pool app will send a notification to your paired mobile device 10 minutes before turning off the lights.
8. Route power and output wiring into the controller and secure electrical conduit. 9. Reconnect wiring and reinstall the Wiring Cover (2). 10. Reestablish power at the main breaker panel. FIGURE 7 INTELLIVIBE™ Pool/Spa Light Controller Installation and User Guide...
Pentair Pool app. possible. Ensure the desired network 2.4 GHz frequency. The Pentair Incompatible WiFi frequency. Pool app is not compatible with 5 GHz networks Install a WiFi signal extender or mesh node as close to the controller as possible.
Page 17
® Mobile device is already paired to to mobile device during controller (displayed as PNR..) from the list of connected controller. Bluetooth pairing. devices. Then re-pair the controller and mobile device. INTELLIVIBE™ Pool/Spa Light Controller Installation and User Guide...
Page 19
NOTES INTELLIVIBE™ Pool/Spa Light Controller Installation and User Guide...
Page 20
10951 WEST LOS ANGELES AVE., MOORPARK, CA 93021 • (805) 553-5000 All indicated Pentair trademarks and logos are property of Pentair or its global affiliates. Third party registered and unregistered trademarks and logos are the property of their respective owners. The Bluetooth® word mark and logo are registered trademarks of Bluetooth SIG, Inc. in the United States and/or other countries.
Need help?
Do you have a question about the INTELLIVIBE and is the answer not in the manual?
Questions and answers