Subscribe to Our Youtube Channel
Related Manuals for Vintage Air 473104
Summary of Contents for Vintage Air 473104
-
Page 1: Cover
1955-56 Chevrolet Control Panel Kit (473104) 18865 Goll St. San Antonio, TX 78266 Phone: 800-862-6658 Sales: sales@vintageair.com Tech Support: tech@vintageair.com www.vintageair.com 903289 REV A 12/01/23, PG 1 OF 12... -
Page 2: Table Of Contents
246204-PUA ECU, or a Gen 5 evaporator unit equipped with a 246404 ECU. Please confirm that your unit has the proper ECU prior to installing the control panel as shown below. A replacement ECU can be purchased from Vintage Air if needed. 903289 REV A 12/01/23, PG 2 OF 12... -
Page 3: Packing List/Parts Disclaimer
Ground Wire ** Before beginning installation, open all packages and check contents of shipment. Please report any shortages directly to Vintage Air within 15 days. After 15 days, Vintage Air will not be responsible for missing or damaged items. 903289 REV A 12/01/23, PG 3 OF 12... -
Page 4: Control Panel Installation
Locknut Figure 1 Side View NOTE: When using a Vintage Air supplied control panel, connect the TAN 20 AWG wire from the Gen IV evaporator wiring harness (232010) or the Gen 5 evaporator wiring harness (231505) to the factory dash lights to enable panel backlighting. -
Page 5: Control Panel Calibration Procedure
Calibration Procedure www.vintageair.com On Vintage Air Gen IV and Gen 5 systems using cable converters or replacement electronic controls, it is necessary to calibrate the system to your specific control panel. This procedure ensures that the travel of your control panel levers or knobs is translated into precise control of the blower speed, temperature blend and mode door position. -
Page 6: Control Panel Calibration Procedure (Cont.)
Control Panel Calibration Procedure (Cont.) www.vintageair.com 1. Turn on the ignition switch (Do not start the engine). 2. Move the control levers/knobs to the positions shown. 3. Connect the white jumper wire to the gray program wire. Wait approximately 5 seconds for the blower speed to change if using a Gen IV system, if using a Gen 5 system wait for the blower to default to medium speed. -
Page 7: Gen Iv Wiring Diagram
Gen IV Wiring Diagram www.vintageair.com 232007-VUR AC ANNUNCIATOR BACKLIGHT POS BACKLIGHT NEG 5V-SW WHT/RED TEMP WIPER WHT/YEL MODE WIPER WHT/GRN FAN WIPER PRE-WIRED VIEWED FROM WIRE SIDE GEN IV ECU 232002-VUA (IF USED) TEMP MODE PROGRAM * DASH LAMP (IF USED) *** WIDE OPEN THROTTLE SWITCH... -
Page 8: Gen 5 Wiring Diagram
Gen 5 Wiring Diagram www.vintageair.com 232007-VUR AC ANNUNCIATOR BACKLIGHT POS BACKLIGHT NEG 5V-SW WHT/RED TEMP WIPER WHT/YEL MODE WIPER WHT/GRN FAN WIPER PRE-WIRED VIEWED FROM WIRE SIDE 232002-VUA GEN 5 ECU (IF USED) TEMP MODE PROGRAM DASH LAMP * (IF USED) PINK WIDE OPEN ** THROTTLE... -
Page 9: Ignition Switch
IGNITION USED. Dash Light: YELLOW SWITCH ORANGE When using a Vintage Air-supplied control panel, connect the tan wire DASH BACK LIGHT+0-12v from the Gen IV evaporator wiring GRAY GRAY WIRE IS USED FOR harness to the factory dash lights to PROGRAMING CONTROLS enable panel backlighting. -
Page 10: Gen 5 Wiring Instructions
(231505) IGNITION Dash Light (Optional): SWITCH WIRING PINK (20 AWG) If using a Vintage Air control panel with HARNESS TAN (20 AWG) back light, connect the 20 AWG tan wire (232020) DASH BACK LIGHT 0 to 12v to the vehicle's dash back light 0-12V... -
Page 11: Heat Operation
Operation of Controls www.vintageair.com On Gen IV and Gen 5 systems with three lever/knob controls, the temperature control toggles between heat and A/C operations. To activate A/C, move the temperature lever/knob all the way to cold and then back it off to the desired vent temperature. -
Page 12: Packing List
Packing List: Control Panel Kit (473104) www.vintageair.com Qty. Part No. Description 493054 Control Panel Assembly 232007-VUR Control Harness, Gen IV/Gen 5 Universal 231520 Ground Wire Checked By: Packed By: Date: NOTE: Images may not depict actual parts and quantities. Refer to packing list for actual parts and quantities.
Need help?
Do you have a question about the 473104 and is the answer not in the manual?
Questions and answers