Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for TOLSEN TOOLS FORCE XPRESS 79650
Summary of Contents for TOLSEN TOOLS FORCE XPRESS 79650
- Page 1 DRILL PRESS INSTRUCTION MANUAL 230V~50Hz 79650 79652 79654 79656 79651 SAVE THIS MANUAL ! You will need this manual for safety instructions, operating procedures and warranty. Put it and the original sales receipt in a safe dry place for future reference.
-
Page 2: Important Safety Information
SAFETY IMPORTANT SAFETY INFORMATION General Tool Safety Warnings WARNING: Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. 1. KEEP GUARDS IN PLACE and in working order. 11. -
Page 3: Grounding Instructions
SAFETY/ GROUNDING INSTRUCTIONS binding of moving parts, breakage of parts, or cutter against the direction of rotation of the mounting, and any other conditions that may blade or cutter only. affect its operation. A guard or other part that is 20. -
Page 4: Vibration Safety
10. Maintain labels and nameplates on the tool. an identical replacement key. These carry important safety information. If unreadable or missing, contact TOLSEN Tools 6. The use of accessories or attachments not recommended by the manufacturer may result for a replacement. -
Page 5: Specifications
SPECIFICATIONS SPECIFICATIONS Stock:79650; 79651(CE) Electrical Rating 230V~50Hz INPUT POWER 350W Spindle Speeds : 620-2620/min 5 Speeds 45° le and right Table Tilt 210mm Swing 50mm Spindle Stroke Spindle Taper 1.5-13mm Chuck Capacity Stock: 79652; 79654 Electrical Rating 230V~50Hz INPUT POWER 550W (79652;79653) 750W (79654;79655) Spindle Speeds... -
Page 6: Before Use
SETUP SETUP Before Use Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. WARNING TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of the tool off... - Page 7 SETUP Table Support 1. Loosen the Pivot Lever (2). Table Support (1) Column 2. Slide the Table Support (1) over the Column. 3. Tighten the Pivot Lever to secure the Table Pivot Lever (2) Support in place. Figure B: Installing Table Support Headstock and Feed Handles 1.
- Page 8 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Tool Set Up TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of the tool off...
-
Page 9: Changing Drill Speed
OPERATING INSTRUCTIONS Setting a Drilling Depth Located on the le side of the Headstock (39) is Lock Nut the depth feed adjustment assembly, which Pointer (3) allows drilling a series of holes to the same Adjustment Nut (2) depth using one setting. Scale Stop Rod (4) 1. -
Page 10: Workpiece And Work Area Set Up
OPERATING INSTRUCTIONS Changing Drill Speed 1. Insert the drill bit into the jaws of the Chuck 3. Tighten the Chuck securely with the included 2.Before tightening the Chuck, ensure that Chuck Key. approximately 1", ensuring that the jaws the drill bit is centered within the jaws. do not touch the flutes of the drill bit. -
Page 11: Cleaning, Maintenance, And Lubrication
OPERATING INSTRUCTIONS / MAINTENANCE AND SERVICING General Operating Instructions 1. Bring the drill bit down with the Feed Handle to do not attempt to stop the spinning with where the hole is to be drilled. Make minor your hands. Step back, and turn the drill workpiece alignment adjustments. -
Page 12: Maintenance And Servicing
MAINTENANCE AND SERVICING Troubleshooting Problem Possible Causes Likely Solutions 1. Check that cord is plugged in. Tool will not start. 1. Cord not connected. 2. Check power at outlet. If outlet is 2. No power at outlet. unpowered, turn off tool and check 3. -
Page 13: Ce Declaration Of Conformity
CE DECLARATION OF CONFORMITY SUZHOU TOLSEN TOOLS CO.,LTD. 198 HUASHAN ROAD, ZHANGJIAGANG, JIANGSU, CHINA Declare that the product 79651 Bench drill ZJ4113-1 230V,50Hz,350W,Class I,IP20 Serial number: N/A Complies with the essential health and safety requirements of the following Directices: EC Machinery Directive 2006/42/EC The EMC Directive 2014/30/EU Standards and technical specifications referred to:... - Page 14 SCAN TO VISIT PRODUCT LINK 79650 SCAN TO VISIT PRODUCT LINK 79651 SCAN TO VISIT PRODUCT LINK 79652 SCAN TO VISIT PRODUCT LINK 79654 SCAN TO VISIT PRODUCT LINK 79656 SUZHOU TOLSEN TOOLS CO.,LTD. www.tolsentools.com TOLSEN is a trademark or registered trademark of TOLSEN TOOLS.
Need help?
Do you have a question about the FORCE XPRESS 79650 and is the answer not in the manual?
Questions and answers