ENGLISH FOR PERFECT RESULTS Thank you for choosing this AEG product. We have created it to give you impeccable performance for many years, with innovative technologies that help make life simpler – features you might not find on ordinary appliances. Please spend a few minutes reading to get the very best from it.
Page 4
Children between 3 and 8 years of age and persons • with very extensive and complex disabilities shall be kept away from the appliance unless continuously supervised. Children of less than 3 years of age should be kept •...
If a tumble dryer is stacked on the top of the washing • machine, make sure to use the correct stacking kit approved by AEG (see more details in chapter "Accessories - Stacking kit"). 2. SAFETY INSTRUCTIONS 2.1 Installation than 0°C or where it is exposed to the...
Service Centre to ensure which • When unpacking the appliance, It is accessories can be used. possible to see water flowing from the drain hose. This is due to the testing 2.2 Electrical connection of the appliance with the use of water in the factory.
ENGLISH circuit boards, electronic displays, applications and are not suitable for pressure switches, thermostats and household room illumination. sensors, software and firmware 2.6 Disposal including reset software, door, door hinge and seals, other seals, door WARNING! locking assembly, plastic peripherals Risk of injury or suffocation.
It gives The washing programme is tailored to the highest use flexibility. the laundry load and the type of fabric • The Wi-Fi connection and Remote without consuming more time, energy Start enable you to start a cycle, to and water than necessary.
ENGLISH 5. INSTALLATION the hose holders. WARNING! Refer to Safety chapters. 5.1 Unpacking 1. Open the door. Remove all the items from the drum. WARNING! It is possible to see water flowing from the drain hose. This is because the washing machine has been tested at the factory.
5.2 Positioning and levelling 1. Install the appliance on a flat hard floor. Make sure that carpets do not stop the air circulation below the appliance. Make sure that the appliance does not touch the wall or other units.
ENGLISH CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose. 2. On the edge of a sink - Fasten the guide to the water tap or to the wall.
6. ACCESSORIES 6.1 Available in Only appropriate www.aeg.com/shop or from accessories approved by authorised dealer AEG ensure the safety standards of the appliance. If Read carefully the instructions supplied unapproved parts are used, with the accessory. any claims will be...
If you install the appliance on a plinth under the washing machine. that is not an accessory supplied by Verify the compatible AEG, secure the appliance with the fixing stacking kit by checking the plates. This spare part is available in web depth of your appliances.
Page 14
The options are not selectable with all washing programmes. Check the compatibility between options and washing programmes in the "AutoDose and options compatibility with programmes" paragraph in the "Programmes" chapter. An option can exclude another one, in this case the appliance doesn't allow you to set the incompatible options together.
Page 15
ENGLISH Press this button repeatedly to activate one of the two options or both. The relevant indicator comes on. • Intensief By setting this option, the indicator appears close to detergent symbol, and the appliance will automatically dose an extra amount of detergent when automatic detergent tank is enabled.
Page 16
Press this button repeatedly to activate one of the two options or both. The relevant indicator comes on in the display. • Remote Select this option to connect appliance with App. Touch this button, the display shows the indicator blinking for a few seconds.
Page 17
ENGLISH When you set a programme, the appliance automatically selects the maximum spin speed. Touch this button repeatedly to: • Decrease the spin speed. The display shows only the spin speeds available for the set pro‐ gramme. • Activate the Rinse Hold option . The water of the last rinse is not drained out to prevent the fabrics from creasing.
Page 18
When you select a washing programme, the appliance automatically proposes a default temperature. Touch this button repeatedly until the desired temperature value ap‐ Tempera‐ pears on the display. tuur touch button When the display shows the indicators , the appliance does not heat the water.
Page 19
ENGLISH It is possible to visualise the total operating time of the appliance in hours, starting from the first switching on. This value will count operat‐ ing time of the cycles (does not include pauses, delayed start time). To visualise this value, proceed as follows: 1.
Page 20
Door locked indicator. Delay start indicator. The digital indicator can show: • Programme duration (e. g. • Delay time (e. g. • Cycle end ( ). • Warning code (e.g. • Indication of total operating hours of the appliance. Refer to the "Oper‐...
ENGLISH Linked mode indicator. It lights when both compartments are linked and filled with the same detergent. AutoDose functionality for softener, is disa‐ ble. These indicators will appear next to detergent tank and softener tank indicators when increasing or decreasing the automatic detergent or softener dosage.
Page 22
AutoDose is activated and the indicators AutoDose and/or are visible on the display. In some programmes, Manual AutoDose is deactivated (the indicators and/or not displayed and the display shows OFF) because there are garments requiring special detergents or treatments. If this is the...
Page 23
ENGLISH 9.3 AutoDose basic setting 1. Identify the water hardness level. Check the water hardness level in The factory pre-set doses for a large your area. The levels are generally load are 90 ml for detergent tank and indicated as: soft, medium and hard. 25 ml for fabric softener tank: the If necessary, please contact your optimal configuration to meet majority...
Page 24
9.5 Filling the detergent and additives on AutoDose system Please read "Detergents and other treatments" in "Hints and tips" chapter. We recommend that you do not exceed the maximum indicated level ( 4. Touch related tank buttons to toggle 1.
Page 25
ENGLISH 4. Gently pour only liquid softener in the 9.6 AutoDose low level AutoDose fabric softener tank . Fill indication up to the maximum indicated level Do not refill the AutoDose tanks unless appliances indicates that one or both tanks are empty. When the activated tank reaches a low level of detergent, related indicator blinks slowly and continuously on the display.
Page 26
9.7 Switching from AutoDose to manual dosing It is possible to disable AutoDose function for one or both tanks by pressing related button symbol. Example: • To switch Fabric Softener tank off, 2. After about 10 seconds the display...
Page 27
ENGLISH 2. Pour the liquid detergent in the 3. If desired, pour the fabric softener in compartment the compartment Manual 3. Gently close the detergent dispenser, 4. Gently close the detergent dispenser, till click engagement. till click engagement. If the machine has not been used for more than 4 weeks with filled tanks, detergent/ softener can become...
This will happen even if the user turned To restart the programme, ensure the AutoDose off. drawer is properly closed and press Start/Pauze button. 10. PROGRAMMES 10.1 Programme Chart Washing programmes The programmes are described in this chart following the order of the selector dial from the top to the bottom.
Page 29
ENGLISH Programme Programme description Outdoor Do not use fabric softener and make sure that there is no softener residue in the detergent dispenser. Outdoor clothing, technical, sport fabrics, waterproof and breathable jackets, shell jackets with a removable fleece or inner insulation. The recommended laundry load is 2,5 kg.
Page 30
Programme Programme description Maintenance cycle with hot water to clean and freshen the drum and Machine clean to remove residue that may cause odour. Before running this cycle, remove all items from the drum. Pour a cup of chlorine bleach or a washing machine cleaner in the washing phase compartment of the detergent dispenser.
Page 31
ENGLISH Programme Default temperature Reference spin Maximum load Temperature range speed Spin speed range 1200 rpm Machine clean 60 °C (1200 - 400) 1) According to Commission Regulation EU 2019/2023, this programme at 40 °C is able to clean normal‐ ly soiled cotton laundry declared to be washable at 40 °C or 60 °C, together in the same cycle.
Page 32
Centrifugeren/ ■ ■ ■ ■ ■ ■ ■ ■ Pompen ■ ■ ■ Tijd besparen ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Startuitstel 1) This option is not available with temperature lower than 40 °C. 2) If you set the shortest duration, we recommend that you decrease the load size. It is possible to fully load the appliance, however the washing results can be less satisfactory.
ENGLISH 10.2 My AEG Care app and additional programmes Some programs are downloadable only by the App My AEG Care. In the App you can find a complete description of each programme. Programme names are subject to change depending on market requirements without notice.
Page 34
Your email and password. If you do not have an account, create a new 4. Configure the "My AEG" app on your one following the instructions in My smart device and follow the AEG Care.
ENGLISH When touching the Start/ Pauze button after the indicator stops blinking, the Remote Start is not activated, but the set programme starts. To remove the Remote Start, tap on the Remote button and confirm by pressing the Start/Pauze button. If you switch the appliance off and on again, the 11.5 Over-the-air update...
12. DAILY USE WARNING! CAUTION! Refer to Safety chapters. Washing heavily oiled, greasy stains could cause damage rubber parts of the 12.1 Activating the appliance washing machine. 1. Connect the mains plug to the mains socket. 12.3 Setting a programme 2.
ENGLISH 12.4 Starting a programme In the display, the indicator of the operating phase starts flashing. with the delay start The programme starts, the door is locked. The display shows the indicator 1. Touch the Startuitstel button repeatedly until the display shows the desired delay time.
Important! If the laundry amount will not The washing programme continues. be reduced, the washing programme 12.9 Cancelling a running starts anyway, despite the overload. In this case, it will be not possible to programme guarantee the best washing results.
ENGLISH in the programme dial, they can be • You must drain the water to open the set via App. door: 1. If necessary, touch the Centrifug. 12.11 End of the programme button to decrease the spin speed proposed by the appliance. When the programme has finished, the 2.
13. HINTS AND TIPS WARNING! Refer to Safety chapters. 13.1 The laundry load • Divide the laundry into: white, coloured, synthetics, delicates and wool. • Follow the washing instructions on the • Empty pockets and unfold the items. laundry care labels.
ENGLISH • The choice and quantity of detergent save detergent, water and time (the will depend on: type of fabric environment is protected too!). (delicates, woollens, cottons, etc), the • Loading the appliance to the colour of clothes, size of the load, maximum capacity indicated for degree of soiling, wash temperature each programmes helps to reduce...
14.4 Descaling Clean drum Every two months If the water hardness in your Clean detergent dis‐ Twice a year area is high or moderate, we recommend that you use a penser and Auto‐ water descaling product for Dose tanks washing machines.
ENGLISH Occasionally, at the end of a cycle the display may show the icon : this is a recommendation to perform the “drum cleaning”. Once the drum cleaning has been performed, the icon disappears. 14.8 Cleaning the detergent Clean it when needed, using ammonia dispenser and the AutoDose cream cleanser agent without scratching tanks...
Page 44
5. Wash the drawer and all inserts under running water. 3. Open the drain plugs of each tank and empty them into a sink. CAUTION! Do not use sharp or metal brushes and sponges. 6. Turn the dispenser up side down and open the bottom cover as indicated in the picture.
Page 45
ENGLISH WARNING! If some residues remain on the back area of tanks, soak detergent drawer in a warm CAUTION! water. Do not use tools to Press the bottom cover as clean it. Before soaking, indicated in the picture. remove the handle by Make sure that it is closed pressing red button and slide properly.
14.9 Cleaning the drain pump b. Place the bottom cover and press till "click" sound. c. Place the top cover on the tanks WARNING! compartment and press till "click" Disconnect the mains plug sound. from the mains socket. d. Replace components on manual compartment.
Page 47
ENGLISH 4. Turn the filter 180 degrees in anti- 10. Clean the filter under the water tap. clockwise direction to open it, without removing. Let the water flow out. 180˚ 11. Put the filter back into the special guides by turning it clockwise. Make 5.
When you drain the water with the emergency drain procedure, you must activate the drain system again: a. Put 2 litres of water in the main wash compartment of the detergent dispenser. b. Start the programme to drain the water.
ENGLISH 3. Put the two ends of the inlet hose in WARNING! a container and let the water flow out Make sure that the of the hose. temperature is higher than 0 4. Empty the drain pump. Refer to the °C before you use the emergency drain procedure.
Page 50
• Make sure that the door is properly closed. The appliance door is open or not closed correctly. • The programme was not finished properly or the appliance stopped too early. Switch the appliance off and on again. Internal fail. No com‐...
Page 51
ENGLISH Problem Possible solution • Make sure that the couplings of the water hoses are tight and there is not water leakages. There is water on the • Make sure that the water inlet hose and the drain hose have floor.
Page 52
Problem Possible solution • Make sure the levelling of the appliance is correct. Refer to The appliance makes "Installation instruction". an unusual noise and • Make sure that the packaging and/or the transit bolts are re‐ vibrates. moved. Refer to "Installation instruction".
ENGLISH 16. CONSUMPTION VALUES 16.1 Introduction See the web link www.theenergylabel.eu for detailed information about Energy Label. The QR code on the energy label supplied with the appliance provides a web link to the information related to the performance of the appliance in the EU EPREL database.
Page 54
Power consumption in different modes Delay start Networked Off (W) Stand-by (W) standby (W) 0.50 0.50 4.00 2.00 Time to Off/Standby mode is 15 minutes maximum. 1) The energy consumption of the connected function is approximately 17.5 kWh per year. To disconnect this function, please refer to the chapter 'Wi-fi - Connectivity setup'.
ENGLISH 17. QUICK GUIDE 17.1 Daily use Connect the mains plug to the mains 2. Set the desired options (1) by means socket. of the corresponding touch buttons. To start the programme, touch the Open the water tap. Start/Pauze (2) button. Load the laundry.
Programmes Load Product description Katoen 9 kg White cotton and coloured cotton. 4 kg Synthetic items or mixed fabric items. Synthetica Delicate fabrics such as acrylics, viscose, polyester 2 kg Fijne was items. Machine washable wool, hand washable wool and deli‐...
Page 60
My AEG Care app The software in this product contains components that are based on free and open source software. AEG gratefully acknowledges the contributions of the open software and robotics communities to the development project. To access the source code of these free and open source software components whose license conditions require publishing, and to see their full copyright information and applicable license terms, please visit: http://aeg.opensoftwarerepository.com (folder NIUS)
Need help?
Do you have a question about the LR639AD44 and is the answer not in the manual?
Questions and answers