Pioneer Premier DEH-P8MP Installation Manual

DEH-P8MP
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit est
conforme à CEMA.
Printed in Thailand
Imprimé en Thaïlande
<CRD3845-A/N> UC <KSNZX> <04D00000>
Connecting the Units
Note:
• This unit is for vehicles with a 12-volt battery and • When an external power amp is being used with
negative grounding. Before installing it in a recre- this system, be sure not to connect the blue/white
ational vehicle, truck, or bus, check the battery lead to the amp's power terminal. Likewise, do
voltage. not connect the blue/white lead to the power ter-
minal of the auto-antenna. Such connection could
• To avoid shorts in the electrical system, be sure to
disconnect the ≠ battery cable before beginning cause excessive current drain and malfunction.
installation. • To avoid short-circuiting, cover the disconnected
• Refer to the owner's manual for details on con- lead with insulating tape. Especially, insulate the
necting the power amp and other units, then make unused speaker leads without fail. There is a pos-
sibility of short-circuiting if the leads are not insu-
connections correctly.
lated.
• Secure the wiring with cable clamps or adhesive
• To prevent incorrect connection, the input side of
tape. To protect the wiring, wrap adhesive tape
the IP-BUS connector is blue, and the output side
around them where they lie against metal parts.
is black. Connect the connectors of the same col-
• Route and secure all wiring so it cannot touch any
ors correctly.
moving parts, such as the gear shift, handbrake
• If this unit is installed in a vehicle that does not
and seat rails. Do not route wiring in places that
have an ACC (accessory) position on the igni-
get hot, such as near the heater outlet. If the insu-
tion switch, the red lead of the unit should be
lation of the wiring melts or gets torn, there is a
connected to a terminal coupled with ignition
danger of the wiring short-circuiting to the vehicle
switch ON/OFF operations. If this is not done,
body.
the vehicle battery may be drained when you
• Don't pass the yellow lead through a hole into the
are away from the vehicle for several hours.
engine compartment to connect to the battery.
(Fig.1)
This will damage the lead insulation and cause a
very dangerous short.
• Do not shorten any leads. If you do, the protection
circuit may fail to work when it should.
• Never feed power to other equipment by cutting
the insulation of the power supply lead of the unit
and tapping into the lead. The current capacity of
the lead will be exceeded, causing overheating.
• When replacing fuse, be sure to use only fuse of
ACC position No ACC position
the rating prescribed on the fuse holder.
• Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded
• The black lead is ground. Please ground this lead
or the left and right ≠ speaker leads are common.
separately from the ground of high-current prod-
• Speakers connected to this unit must be high- ucts such as power amps.
power types with minimum rating of 40 W and If you ground the products together and the
impedance of 4 to 8 ohms. Connecting speakers ground becomes detached, there is a risk of dam-
with output and/or impedance values other than age to the products or fire.
those noted here may result in the speakers
• When there is no place surrounding this unit in
catching fire, emitting smoke or becoming dam-
which to ground and you wish to extend the black
aged.
lead, use a cable with the same or greater thick-
• When this product's source is switched ON, a ness (official conductor area of 3.0mm
control signal is output through the blue/white black lead and connect firmly to a metal portion
lead. Connect to an external power amp's system of the vehicle.
remote control or the car's Auto-antenna relay
control terminal (max. 300 mA 12 V DC). If the
• Cords for this product and those for other prod-
car features a glass antenna, connect to the anten-
ucts may be different colors even if they have
na booster power supply terminal.
the same function. When connecting this product
to another product, refer to the supplied manuals
of both products and connect cords that have the
same function.
CAUTION:
The default output settings values for this unit are
40W × 4ch. When using this unit at 60W × 4ch you
must adjust the settings switch on the bottom of this
unit. (Fig. 2)
Fig. 2
Follow the below upon connecting with the output set-
tings for this unit set at 60W × 4ch. Connecting with
any other method may result in malfunction.
• Connect the accessory (long red lead) to an acces-
sory circuit of 10A or more when the vehicle
engine switch is set to the ACC position. If the
current is less than 10A the accessory fuse on the
vehicle may be interrupted.
• If this unit is installed in a vehicle that does not
have an ACC (accessory) position on the ignition
switch, install a switch to turn on/off the ACC.
• Connect the battery (yellow lead) to a battery
circuit of 10A or more despite if the vehicle engine
switch is ON or OFF. If the current is less than 10A
the battery fuse on the vehicle may be interrupted.
• If the accessory fuse for the vehicle is less than
10A, use a battery cable such as the RD-221 (sold
separately) for the accessory (long red lead) and
feed the electricity directly from the battery.
• When feeding electricity directly from the battery
for the accessory (long red lead) through a battery
Fig. 1
cable, connect the accessory (short red lead) to the
accessory circuit for the vehicle being supplied with
electricity while the vehicle engine switch is set to
the ACC position.
• If the battery fuse for the vehicle is less than 10A,
use a battery cable such as the RD-221 (sold sepa-
rately) for the battery (yellow lead) and feed the
electricity directly from the battery.
• This unit is for vehicles with a 12-volt battery and
negative grounding. Before installing it in a recre-
2 ) as the ational vehicle, truck, or bus, check the battery volt-
age.
• Speakers connected to this unit must be high-power
types with minimum rating of 60 W and impedance
of 4 to 8 ohms. Connecting speakers with output
and/or impedance values other than those noted
here may result in the speakers catching fire, emit-
ting smoke or becoming damaged.
<ENGLISH>