Installation; Connecting To Separately Sold Power Amp; Din Front-Mount - Pioneer Premier DEH-P8MP Installation Manual

Connecting the Units

Connecting to separately sold power amp

Front output
(FRONT OUTPUT)
Antenna jack
Rear output
(REAR OUTPUT)
15 cm
(5-7/8 in.)
This product
Subwoofer output or Non Fading Output
(SUBWOOFER or NON-FADING OUTPUT)
IP-BUS input
(Blue)
Multi-CD player
Jack for Wired Remote Control
(sold separately)
15 cm (5-7/8 in.)
IP-BUS cable
Blue/white
Refer to Fig. 3 and Fig. 4.
To system control terminal of the power
amp or Auto-antenna relay control
terminal (max. 300 mA 12 V DC).
White Gray
+ +
Front speaker Front speaker
≠ ≠
White/black Gray/black
Left Right
Green Violet
+ +
Rear speaker Rear speaker
or Subwoofer or Subwoofer
≠ ≠
Green/black Violet/black
With a 2 speaker system, do not connect
anything to the speaker leads that are not
connected to speakers.
<ENGLISH>
Power amp
(sold separately)
Power amp
Connecting cords (sold separately)
with RCA pin plugs
(sold separately)
Power amp
(sold separately)
System remote control
+ +
Front speaker Front speaker
≠ ≠
+ +
Rear speaker Rear speaker
≠ ≠
Left Right
+ +
Subwoofer Subwoofer
≠ ≠
Note:
Perform these connections when using the
Change the initial setting of this unit (refer
optional amplifier.
to the Operation Manual). The subwoofer
output of this unit is monaural.

Installation

Note:
• Before finally installing the unit, connect the • If installation angle exceeds 60° from horizontal,
wiring temporarily, making sure it is all connected the unit might not give its optimum performance.
up properly, and the unit and the system work (Fig. 6)
properly.
• Use only the parts included with the unit to ensure
proper installation. The use of unauthorized parts
can cause malfunctions.
• Consult with your nearest dealer if installation
requires the drilling of holes or other modifications
of the vehicle.
• Install the unit where it does not get in the driver's
way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.
• The semiconductor laser will be damaged if it
overheats, so don't install the unit anywhere hot —
for instance, near a heater outlet.
DIN Front/Rear-mount
This unit can be properly installed either from "Front" (conventional DIN Front-mount) or
"Rear" (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit
chassis). For details, refer to the following illustrated installation methods.

DIN Front-mount

Installation with the rubber bush (Fig. 7)
Holder
After inserting the holder into the
dashboard, then select the appropriate
tabs according to the thickness of the
dashboard material and bend them.
Dashboard
(Install as firmly as possible using the
182 top and bottom tabs. To secure, bend
the tabs 90 degrees.)
53
Rubber bush
Screw
Fig. 5
Installation without the rubber bush (Fig. 8)
Dashboard
Nut (5 mm)
Drill a 5.5 – 6.0 mm
diameter hole.
60°
Screw (5 × 16 mm)
Screw
Nut (5 mm)
Fig. 6
Removing the Unit (Fig. 9) (Fig. 10)
Frame
Insert the release pin into the hole in
the bottom of the frame and pull out
to remove the frame.
(When reattaching the frame, point
the side with a groove downwards
and attach it.)
Insert the supplied extraction keys
into the unit, as shown in the figure,
until they click into place. Keeping
the keys pressed against the sides of
the unit, pull the unit out.
Fig. 7
<ENGLISH>
Strap
Be sure to use the strap to secure the back
of the unit in place. The strap can be bent
by hand to the desired angle.
Fig. 8
Fig. 9
Fig. 10