Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Draper SFAI12
Summary of Contents for Draper SFAI12
- Page 1 Original Instructions Version 2 - January 2025 AIR IMPACT WRENCH 65017...
-
Page 2: Product Reference
All photographs and drawings within this manual are document is part of the product; retain it for the life supplied by Draper Tools to help illustrate correct of the product, passing it on to subsequent holders. operation of the product. -
Page 3: Table Of Contents
2. Contents 1. Preface 1.1 Product Reference 1.2 Revisions 1.3 Understanding the Safety Content of This Manual 1.4 Copyright © Notice 2. Contents 3. Product Introduction 3.1 Intended Use 3.2 Specification 4. Health and Safety Information 4.1 General Health and Safety Precautions 4.2 Additional Safety Instructions for Compressed Air 4.3 Additional Safety Instructions for Air Impact Wrenches 4.4 Residual Risk... -
Page 4: Product Introduction
Any other application beyond the conditions established for use will be considered misuse. Draper Tools accepts no responsibility for improper use of this product. 3.2 Specification Stock No. -
Page 5: Health And Safety Information
Use of these substances may cause the vibration injuries. product to explode. • Use only sizes and types of accessories and • Draper Tools recommends the use of a whip hose consumables that are recommended by the tool between the tool and the air supply to reduce manufacturer. -
Page 6: Residual Risk
4. Health and Safety Information • Unexpected direction of inserted tool movement can cause a hazardous situation. • Use only impact sockets and adaptors which are in good condition and are intended for use with this tool. • Adopt a suitable posture to counteract normal or unexpected movement due to reaction forces from the wrench. -
Page 7: Identification And Unpacking
5. Identification and Unpacking 5.1 Product Overview Variable speed trigger. Composite body. Anvil. 1/4” BSP (female) air inlet. Anvil ring. Air line coupling screw adaptor. Reverse/forward speed selector. 5.2 Packaging WARNING! Keep packaging materials out of Keep the product packaging for the duration of the reach of children. -
Page 8: Assembly Instructions
• When using an air tool with a hose over 25ft long, optimum performance. Draper Tools recommends increasing the bore of the • The compressed air system must be controlled by a hose to the next largest available size (i.e. increase combination pressure regulator, in-line lubricator and 3/8”... -
Page 9: Operating Instructions
7. Operating Instructions 7.1 Trigger Switch (Fig.3) Note: Before connecting the impact wrench to the air supply reduce the line pressure according to the specification. − Confirm direction of rotation prior to starting. Pull trigger (1) to operate the impact wrench. −... -
Page 10: Maintenance And Troubleshooting
8. Maintenance and Troubleshooting 8.2 After Use Maintenance Checks WARNING! • Repeat the above procedures. • Disconnect from the air supply before carrying out any adjustments, servicing or maintenance. • Lubricate the tool with approximately 1.5ml of oil directly down the air inlet. • Never use any sockets or accessories that are not hardened for impact use. -
Page 11: Troubleshooting
Draper Tools. Chrome plated sockets can shatter and cause injury. Tool runs at normal – Motor parts worn. – Return to service centre or contact Draper speed but loses power Tools for advice. under load. Tool will not shut off. -
Page 12: Spares, Returns And Disposal
9. Spares, Returns and Disposal At the end of its working life, dispose of the product responsibly and in line with local regulations. Recycle where possible. • DO NOT dispose of this product with domestic waste; most local authorities provide appropriate recycling facilities. -
Page 13: Warranty
This warranty period covers parts and labour for 6 months from the date of purchase. Your Draper Tools guarantee is not effective until you can produce, upon request, a dated receipt or invoice to This warranty does not apply to any consumable parts, verify your purchase within the guarantee period. - Page 14 Notes – 14 –...
- Page 15 Notes – 15 –...
-
Page 16: Contact Details
Product Helpline: +44 (0) 23 8049 4344 Telephone Sales Desk: +44 (0) 23 8049 4333 General Enquiries: +44 (0) 23 8026 6355 Please contact the Draper Tools Product Helpline for repair and servicing enquiries. © Published by Draper Tools Limited © Published by Draper Tools Limited...
Need help?
Do you have a question about the SFAI12 and is the answer not in the manual?
Questions and answers