Page 2
No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. The information provided in this manual is intended to be accurate and reliable.
Page 3
This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This type of cable is available from Advantech. Please contact your local supplier for ordering information.
Page 4
Note! Notes provide additional optional information. Document Feedback To assist us with improving this manual, we welcome all comments and constructive criticism. Please send all feedback in writing to support@advantech.com. Selection Guide w/ P/N Part No. Description COM-HPC Development Board for Client Pinout with 5 mm in height...
Page 5
In accordance with IEC 704-1:1982 specifications, the sound pressure level at the operator’s position does not exceed 70 dB (A). DISCLAIMER: These instructions are provided according to IEC 704-1 standards. Advantech disclaims all responsibility for the accuracy of any statements contained herein. SOM-DH3000 User Manual...
Page 8
Table 3.28:PWR_LED_PH1 Power LED Pin Header....28 3.1.12 Jumper Setting................29 Table 3.29:BIOS_SEL Pin Header ..........29 Table 3.30:J25, J26 SOM-DH3000 Voltage Input (VIN) Selection Table 3.31:J22 COMe Module +V5SB Supply ......30 Table 3.32:BATLOW1 ..............30 Table 3.33:PSON1 ATX/AT Mode Selection......30 Table 3.34:J19 Carrier Board SPI power supply ......
Page 9
Chapter General Information This chapter details background information on the SOM-DH3000 Development Board for COM-HPC. Sections include: Introduction Functional Block Diagram Product Specifications...
Page 10
Key connectors and HD audio. It is designed to fulfill multiple applications for end customers and can emulate required functions as a reference design board. Indeed, customers can integrate the SOM-DH3000 directly into their product as an applica- tion board.
Page 13
Chapter Mechanical Information This chapter details mechanical information on the SOM-DH3000 Development Board for COM-HPC Sections include: Board Information Mechanical Diagrams Assembly Diagrams...
Page 14
Board Information The figures below indicate the main chips on SOM-DH3000 Development Board for COM-HPC. Figure 2.1 Board Chips ID - Front SOM-DH3000 User Manual...
Page 15
Mechanical Diagram For more information regarding the following 2D/3D models, please visit the Advant- ech COM support service website: http://com.advantech.com. Figure 2.2 Board Mechanical Diagram - Front Figure 2.3 Board Mechanical Diagram - Side 1 Figure 2.4 Board Mechanical Diagram - Side 2...
Page 16
Figure 2.5 Board Mechanical Diagram - Side 3 SOM-DH3000 User Manual...
Page 17
Assembly Diagram These figures demonstrate the order of assembly for attaching the thermal module and COM module to carrier board. Figure 2.6 Assembly Diagram SOM-DH3000 User Manual...
Page 19
Chapter Connectors and Jumper Settings This chapter details information on the connector and jumper set- tings for the SOM-DH3000 Devel- opment Board for COM-HPC.
Page 20
SOM-DH3000 Connectors and Jumper Settings 3.1.1 Connector Locations Figure 3.1 Connector Locations SOM-DH3000 User Manual...
Page 29
Table 3.10: CN15_GPIO GPIO Pin Header Signal Signal GPIO0 GPIO6 GPIO1 GPIO7 GPIO2 GPIO8 GPIO3 GPIO9 GPIO4 GPIO10 GPIO5 GPIO11 Table 3.11: CN14_GP_SPI Pin Header Signal Signal GPSPI_CLK GPSPI_MISO PLTRST#_OTHER2 GPSPI_MOSI GPSPI_CS0# +V3.3 GPSPI_ALERT# +V1.8_DUAL PLTRST#_OTHER2 +V5_DUAL SOM-DH3000 User Manual...
Page 30
Table 3.12: CN16_eSPI Pin Header Signal Signal CLK33M_PH LPC_PH_AD1 ESPI_LPC_RST# LPC_PH_AD0 LPC_PH_FRAME# +V3.3 LPC_PH_AD3 LPC_PH_AD2 Pull-up via 10K ohm to +V3.3 SERIRQ_PH ESPI_LPC_RST# Table 3.13: BAT1 RTC Battery Connector Signal +VBAT_BH SOM-DH3000 User Manual...
Page 31
Table 3.14: DCIN0 Wide Range DC Input Connector2 Signal +VDC +VDC Table 3.15: SYS_FAN1 System Fan Connector Signal SYS_FAN_SENSE +V12 Table 3.16: SMART_FAN1 Smart Fan Connector Signal +V12 FANTACH_R1 FANPWM_R SOM-DH3000 User Manual...
Page 32
Table 3.17: I2C0 I2C Wafer Box(+3.3V) Signal I2C_DAT I2C_CLK +V3.3_DUAL Table 3.18: I2C1 I2C Wafer Box(+1.8V) Signal I2C_DAT I2C_CLK +V1.8_DUAL Table 3.19: SMB1 SMBus Wafer Box Signal SMB_DAT SMB_CLK +V3.3_DUAL SOM-DH3000 User Manual...
Page 33
Table 3.20: CSI0_B2B1 Connector Signal Signal +V3.3 +V3.3 CSI0_RX0+ CSI0_RX0- CSI0_RX1+ CSI0_RX1- CSI0_RX2+ CSI0_RX2- CSI0_RST# CSI0_RX3+ CSI0_RX3- CSI0_CLK+ CSI0_CLK- CSI0_I2C_CLK CSI0_I2C_DAT CSI0_ENA CSI0_MCLK SOM-DH3000 User Manual...
Page 34
Table 3.21: CSI1_B2B1 Connector Signal Signal +V3.3 +V3.3 CSI1_RX0+ CSI1_RX0- CSI1_RX1+ CSI1_RX1- CSI1_RX2+ CSI1_RX2- CSI1_RST# CSI1_RX3+ CSI1_RX3- CSI1_CLK+ CSI1_CLK- CSI1_I2C_CLK CSI1_I2C_DAT CSI1_ENA CSI1_MCLK SOM-DH3000 User Manual...
Page 35
Table 3.22: Table 3.22: I2S_CN1 Bus Connector Signal Signal I2S_VDD I2S_DIN I2S_LRCLK I2S_CLK I2S_DOUT I2S_MCLK Table 3.23: SDNW_CN1 Connector Signal Signal +V1.8 SNDW_CLK2 SNDW_CLK3 SNDW_DAT2 SNDW_DAT3 SNDW_DMIC_CLK1 SNDW_DMIC_DAT1 Table 3.24: SPI_CN1 SPI BIOS Pin Header Signal Signal +V3.3M_SPI_J Q_SPI_PH_CS# Q_SPI_PH_CLK Q_SPI_PH_MISO Q_SPI_PH_MOSI SOM-DH3000 User Manual...
Page 36
Table 3.25: PWRBTN_PH1 PWRBTN Pin Header Signal PWRBTN# Table 3.26: SYS_RESET_PH1 SYS RESET Pin Header Signal PM_EXTRST# Table 3.27: SATA_ACT_PH1 SATA ACT# Pin Header Signal BATLOW# Table 3.28: PWR_LED_PH1 Power LED Pin Header Signal Pull-up via 330 ohm to +V5 SOM-DH3000 User Manual...
Page 37
3.1.12 Jumper Setting Table 3.29: BIOS_SEL Pin Header Function BIOS_SEL 2~0 100ohm to GND Table 3.30: J25, J26 SOM-DH3000 Voltage Input (VIN) Selection Function J16 1-2 Supply ATX (+V12) to VIN [Default] J17 1-2 J17 1-2 Supply DCIN (+VDC) to VIN...
Page 38
Function Battery Low Normal [Default] Table 3.33: PSON1 ATX/AT Mode Selection Function AT Mode ATX Mode [Default] Table 3.34: J19 Carrier Board SPI power supply Function Carrier Board SPI power supply [Default] Carrier Board SPI no power SOM-DH3000 User Manual...
Page 39
+VEDP_PANEL_PWR is +V5 J15 2 – J16 2 +VEDP_PANEL_PWR is +V12 Table 3.37: CB_PWROK Power ok signal Pull Down\Floating Selection Function Normal POWROK to GND Table 3.38: J6 LVDS_INVERTER Selection Function INVERTER is +V5 [Default] INVERTER is +V12 SOM-DH3000 User Manual...
Page 40
Table 3.39: J18 Normal Operation/Clear COMS Selection Function Clear CMOS Normal Operation [Default] Table 3.40: J7 PCIE_RD_MODE_SELECT Function I2C Mode Pin Mode [Default] Table 3.41: CN13 I2S_VDD Function +V3.3 [Default] +V1.8 Table 3.42: SMB_ALT1 SMB_ALT# Function SMBus Alert Normal [Default] SOM-DH3000 User Manual...
Page 41
SPI ROM from Carrier Board. Table 3.45: CN18_SML_ECI2C Signal Signal USB_PD_I2C_CLK I2C_EC_SCL_A USB_PD_I2C_DAT I2C_EC_SDA_A USB_PD_ALERT# I2C_EC_ALT#_A PD_SML_SCL I2C_SOC_SCL_A PD_SML_DAT I2C_SOC_SDA_A PMCALERT# I2C_SOC_ALT#_A Jumper 1-X [Default] Jumper 3-X [Default] Jumper 5-X [Default] Jumper 7-X [Default] Jumper 9-X [Default] Jumper 11-X [Default] SOM-DH3000 User Manual...
Need help?
Do you have a question about the SOM-DH3000 and is the answer not in the manual?
Questions and answers