Page 1
— Quick Start Guide— Model: CPE242 Note: A. Thank you for order and using our product, please read the manual carefully before use. If there are any problems during the use, please contact us in time; Customer Service Email: support@ueevii.com...
The AP can be receiving wireless data transmitted from multiple Clients, and it is easy and convenient for centralized management of the remote equipment. Package Included: 2 x CPE242 Wireless Bridge 2 x PoE Adapter 2 x Cable Tie 2 x Network Cable...
Product Features: 1. Built-in 8dBi high-gain antenna, which can meet the long-distance wireless transmission within 1KM, and can realize point-to-point, point- to-multipoint outdoor coverage and application; 2. Support 24PoE power supply mode; 3. Digital display, easy debugging without computer; 4. Dual network port design, easy to expand the terminal. 5.
Page 4
2.4G receiving 802.11b -85dBm -94dBm sensitivity 802.11g -72dBm -88dBm 802.11n HT20 MCS7 -68dBm MCS0 -86dBm 802.11n HT40 MCS7 -66dBm MCS0 -85dBm 2.4G EVM 802.11b:≤-10 dB ;802.11g: ≤-25 dB ;802.11n: ≤-28 dB frequency deviation ±20ppm (ppm) port(WAN) 1*10/100M WAN port, support 24V POE port(LAN) 1*10/100M LAN port button...
Page 5
Interface & LED Details 1.1 WAN 10/100Mbps RJ45 port, 1 LAN 10/100Mbps RJ45 port,support PoE power supply. 2.4 LED Indicator lights included PWR light, LAN light, WAN light, WiFi light PWR Light: Solid means power supply is normal LAN Light: Solid means LAN port has been connected WAN Light: Solid means WAN port has been connected WiFi Light: Blinking state indicates normal work Lights...
Button Operation: Button Function Operation Push the H-C button to H or C, Switch master and H-C button wait 10 seconds to complete the slave bridge switch Long press the "RST" button for Reset wireless bridge 10 seconds to reset RST button After setting the master and slave bridge, within 1 minute,...
Quick Start 1. PoE Power Supply The CPE242 wireless bridge adopts a PoE power supply, which is easy to install and manage while saving costs. 1. According to the requirements, prepare a long enough network cable (Recommended within 20 meters)to connect the wireless bridge and the PoE power supply.
Page 8
2. The 2 wireless network bridges must be installed face to face as much as possible, with no architectural obstacles and strong electricity and strong magnetism in between. 3. The theoretical working distance of CPE242 wireless bridge is 1KM, and the actual application should be less than 1KM. 4. WiFi Function 1.
Page 9
5. Application Case 1. Point-to-point extended of surveillance cameras range Master Bridge Slave Bridge IP Camera Computer Switch IP Camera IP Camera 2. Point-to-multiple point extended of surveillance cameras range Slave Bridge IP Camera Master Bridge Computer IP Camera 60° IP Camera IP Camera 3.
Advanced settings Note: You can enable the device without advanced settings. Computer Access 1. Connect the CPE to the computer Refer to the figure left to connect the CPE to the computer through a PoE adapter and an Ethernet cable. POE Charger 2.
Page 11
Step 1: Find and open "Open Network and Sharing Center" on your computer. Tips: click the network icon in the lower right corner of the computer. Step 2: Find and open the "Change adapter settings", select "Local Area Connection" to right-click to open the network properties. Refer to the picture above to open.
If there are any problems during the use, please contact us in time; B. The installation of this device requires some network knowledge. If you can't install it, please let us know or contact the professional. support@ueevii.com Technical Service Email: //www.facebook.com/UeeVii FaceBook:https: //www.facebook.com/groups/8869731233069487 ...
Need help?
Do you have a question about the CPE242 and is the answer not in the manual?
Questions and answers