Bobtot Sound Air1 Manual

What's in the Box

Check to make sure you have everything below.

1. 1* Sound Air1 Portable Speaker
2. 1* Type-C USB Charging Cable
3. 1* 3.5mm AUX Audio Cable
4. 1* Quick Start Quide

Device Overview

1. Power On/Off
2. Previous Button
3. Play/Pause
4. TWS/Mode
5. Indicator light
6. Next Button
7. Volume +
8. Volume -
9. AUX jack
10. USB port
11. Type-C charging port
12. Indicator light
13. TF card jack

Buttons and Ports

	Power On/Off Long press and hold to turn the speaker on/off.
	Play/Pause/Answer Button Short press to pause/play the music. Short press to accept an incoming call. (BT mode) Double click to call back. (BT mode) Long press to reject an incoming call. (BT mode) Long press to disconnect/reback BT.
	TWS/Mode Long Press to connect with two speakers. Long Press to disconnect both speakers.
	Previous Button Short Press to go to previous song.
	Next Button Short Press to go to next song.
	Volume + Press to increase the volume.
	Volume - Press to decrease the volume

Charging Your Device

Plug the included USB type-C cable into the speaker's charging port, and connect another end of the cable to a power adapter (not included). Allow approximately 4.5 hours to full charge the battery.
When the battery is low and the blue light slow flash, please charge it.
The indicate light is red color when it's charging.
The red light will be off when it's full charged.
Note: We recommend using a USB wall adapter with a DC 5V output.

Initial Setup

1. Once your speaker is fully charged, press and hold the Power button until you hear a voice prompt indicating the device has entered BT paring mode.
2. On your smartphone or tablet, search for the BT device named "Bobtot Sound Air1" and tap to connect.
3. A prompt will play once pairing is successful.

Note:

1. When you turn on the speaker but no connection, it will automatically shut down after 10 minutes.
2. When you connected the speaker but no playback, it will automatically shut down after 20 minutes.

TWS Sync Mode

1. Long press the "" about 2s on both speakers to turn them on, and the blue light flashes.
2. Long press the "" on any one speaker, a prompt sound "connected" indicates the speakers enter into pairing mode, the indicator light of one speaker turned solid blue.
3. On your smartphone or tablet, search for the BT device named "Bobtot Sound Air1" and connect it, you could hear the sound "connected" again, which means connect successfully. You can enjoy the music with two speakers together.

Notes:

• In TWS Mode, turn off one of the speakers, both of them are off.
• Long press "" to exit TWS mode

Light Status

	Blue light flash: in BT pairing or TWS pairing status
	Blue light slow flash: Low battery
	Stay red light: Charging
	Red light off: Full charge

Hands-Free Calling

	Play/Pause/Answer Button Short press to pause/play the music. Short press to accept an incoming call. (BT mode) Double click to call back. (BT mode) Long press to reject an incoming call. (BT mode) Long press to disconnect/reback.(BT mode)
	Volume Up Press to increase the volume.
	Volume Down Press to decrease the volume.

Resetting Your Device

If your speaker is not operating properly, you may reset it. To do so, press and hold the power button for approximately 8s until the speaker powers off, and then power it on again as usual.

Specifications

• Model Name: Sound Air1
• Outdoor Portable Wireless Speaker
• Input Power: DC 5V
• Impedance: 3Ω
• Signal to Noise Ratio: ≥78dB
• IPX6 water-resistant, sprayproof
• Built-in rechargeable battery
• Built-in Mic
• Range 33ft (10m)
• Frequency Response: 180Hz-18KHz
• TWS Sync Mode (Pair 2 of these speakers together)
• Up to 25 hours of playtime (battery life is measured as number of playtime with volume set at 50%)

Need help?
If you have any questions or concerns, please don't hesitate to reach out to us.
We will be happy to assist you:
Call or Message: +1 888 572 1718
Email: service@bobtot.net
bobtot.net