Subscribe to Our Youtube Channel
Related Manuals for BRAVILOR BONAMAT B-Compact MB-001
Summary of Contents for BRAVILOR BONAMAT B-Compact MB-001
- Page 1 B-Compact OPERATING MANUAL Model-no: • MB-001 Original document by manufacturer version x.x | 2025-01-28...
- Page 2 All rights reserved. No part of this document may be copied and/or published by means of printing, photocopying, microfilming or by any other means whatsoever without the prior written consent of the manufacturer. This also applies to the included drawings and/or diagrams. The information in this document is based on data that was available at the time the design, the material characteristics and the operating methods were published, meaning that this document is subject to change.
-
Page 3: Table Of Contents
Table of contents 1. General information ............1.1 Manual languages . -
Page 5: General Information
1. General information 1.1 Manual languages This manual is supplied with the B-Compact. Other available languages can be downloaded, scan the QR code or double-click/copy the link below. 2.2 Warning ► While filled, loose containers may not be moved by the handles. Handles have been provided to facilitate the handling of empty containers. -
Page 6: Controls
2.3 Controls The basic buttons are described underneath. basic buttons function Indicators function feedback value with number adjust value separator place lid fill time heat up temperature unit brew lock circulate B-compact is live settings ready to dispense cancel... -
Page 7: Installation And Prepare For Use
3. Installation and prepare for use 3.1 Installation Requirments: • water hardness : min. 5 dH • min. water pressure (supply) : min. 100 kPa (1 bar) : max. 1000 kPa (10 bar) • flow rate : 0,5 l/min • electrical values : see the identification plate 1. Read the safety booklet ►... -
Page 8: Start Up
3.2 Start up After switching on, the control display shows the set values a after the other. If any of the 7 keys are pressed during start-up, the B-Compact goes straight to standby. Start: • make sure that the water supply is open •... -
Page 9: Stop Button
Information screen: • last set keep warm temperature is displayed • beep sounds • wait for the next screen 3.2d 3.3 Stop button The "stop button" will stop "automatic processes" if they are running... -
Page 10: Standby
3.4 Standby The device is equipped with a standby mode this is used to save energy consumption when the B-Compact is not used. When standby becomes active, the following actions are performed: • pump : disabled • heating : disabled •... -
Page 11: Prepare For Use
3.5.1a 2. remove the complete filter cone 3. remove the filter with the old coffee grounds 3.5.1b clean the cone if neccessary (see fig. 4.1b) 5. place a new filter paper ► Exclusively use the Bravilor Bonamat filter paper or filter paper ® of the same quality. 6. add the coffee grind, spread the coffee bed evenly ► The use of normal grind is recommended (approx. 40-50 g/l.) 7. place the filter cone, with coffee, in the B-Compact 8. -
Page 12: Cleaning
4. Cleaning It is important that the Bolero is kept clean, what can be cleaned: Daily Weekly Periodic drip tray coffee kettle coffee kettle (thorough) gauge glass filter cone the outside ► Never clean parts of the B-Compact in the dishwasher, only if this is explicitly stated. ►... -
Page 13: Weekly Cleaning
Outside: 1. switch off the B-Compact 2. clean the outside, using a damp cloth 4.1d 4.2 Weekly cleaning Coffee kettle (thorough): 1. switch off the B-Compact 2. remove the drip-tray 4.2a 3. put out the drain hose 4. place a bucket under the drain hose 5. - Page 14 open the lid and remove the filter cone, see fig. 3.5.1a ► Use only a non aggressive product due to save the gaskets. Follow the instructions for use of the anti-coffee agent. 8. pour a solution of an anti-coffee agent into the coffee kettle 9. place the filter cone, with coffee, in the B-Compact 10. close the lid 11. switch on the B-Compact 12. press the "fill button" and keep it pressed until the water level is approx.
-
Page 15: Periodic Cleaning
4.3 Periodic cleaning 4.3.1 Clean the gauge glass Over time, coffee deposits can form in the gauge glass. It may therefore be necessary to clean the gauge glass separately with a gauge glass brush. ► Handle the gauge glass with care, it is very fragile. 1. switch off the B-Compact 2. drain through the manual tap 3. -
Page 17: Functions
5. Functions 5.1 Automatic brewing The fully automatic brewing process is described in this section. The following sections describe the manual startable parts. Standby mode, when B-Compact is empty: • press the "brew button" 5.1a Information screen filling and heating: ► The fill animation (see §5.2 on p.15) alternating with the current water temperature. - Page 18 Information screen, heating: ► The temperature continues to rise until the set temperature is reached, then the following screen appears. • to cancel the process, press and go to the standby mode temperature < 75°C (167°F) go to screen 3.4b on p.6 » temperature ≥ 75°C (167°F) go to screen 3.4c on p.6 » 5.1c Information screen coffee brewing process: ► The "brew" indicator light is flashing at normal speed and the coffee brewing time is decreasing.
-
Page 19: Fill
5.2 Fill ► The B-Compact must always be filled with cold water from the mains During filling, the display shows the following as an animation. Standby mode, when B-Compact is empty: Automatic filling: • press once to go to the next screen ► Once this procedure is completed, the remaining buttons are available. - Page 20 Semi-automatic filling ► The "Fill" indicator is flashing and the fill animationis displayed. • when the button is released the B-Compact will go in standby mode temperature < 75°C (167°F) go to screen 3.4b on p.6 » temperature ≥ 75°C (167°F) go to screen 3.4c on p.6 » 5.2d ...
-
Page 21: Fill And Heat
5.3 Fill and heat Standby mode, when B-Compact is empty: • press the "heat button" 5.3a Information screen filling and heating: ► The fill animation (see §5.2 on p.15) alternating with the current water temperature. ► The "fill" and "heat" indicator lights are flashing. ► When the B-Compact is filled the next screen appears •... - Page 22 Information screen, heating: ► The "heat" indicator light is flashing. • a beep sounds when the B-Compact set temperature has reached then go to the next screen ► Depending on irregularities in the water supply at the location, the automatic filling procedure may result in an incompletely filled B-compact.
-
Page 23: Circulate
5.4 Circulate This function is only active when fluid is registered in the B-Compact, allowing the pump to circulate the fluid. If this function is used with fluid of 50°C or more, the lid must be in place, otherwise the lid protection will be activated (see §6.1 on p.23) Set the circulate time: • press and go to the next screen ► The "circulate" indicator light is flashing. • press the to set the circulate time • to cancel the process, press and go to the standby mode 5.4a ... - Page 24 Circulation animation progress screen: • the B-Compact returns to the point at which it was activated » standby 3.4b on p.6 3.4c on p.6 depending on the fluid temperature » automatic brewing 5.1f on p.14 filling 5.2c on p.15 » » heating 5.3d on p.18 5.4d ...
-
Page 25: Setting Items
5.5 Setting items The setting button is available if no other processes are running Setting Standard adjust from - to S 01 brew temperature 95°C (203°F) 85 - 95°C (185 - 203°F) S 02 brew time 10 minutes 4 - 16 minutes S 03 heat temperature 85°C (185°F) 75 - 90°C (167 - 194°F) S 04... - Page 26 Heat temperature (S 03): • press the to change the value • press to save the changes • when ready a a beep sounds and the carousel is displayed • to cancel press and go back to the carousel 5.5d Pause times (S 04): ►...
-
Page 27: Special Functions
6. Special functions 6.1 Lid warning The lid can be removed from the B-Compact without consequences when the fluid temperature is below 50°C (120°F), since this is a safe temperature for people. If different, the current process running is interrupted when the lid is removed. If a process is started while the fluid temperature is between 0-50°C (32-122°F), the lid indicator will flash as a reminder that the lid must be in place. As soon as the fluid reaches 50°C (122°F) the text "lid" appears and the B-Compact stops heating, the temperature is kept at 50°C (122°F) , as soon as the lid is placed the procedure started can continue. Lid warning: ► The lid is not present while the temperature is higher then 50°C (120°F). • a beep sounds , the lid indicator lights up and "lid" is flashing in the display •... -
Page 28: Lock Mode
6.2 Lock mode The machine can be locked when the machine is: • in standby • filling • heating • brewing • circulating Lock the B-Compact: • press together for 2 sec. • a beep sounds go to the next screen •... -
Page 29: Errors
6.3 7. Errors Error messages appear when an error is detected by the B-Compacts operating system. The error can be accompanied by an acoustic signal (1 sec on - 2 sec off - 1 sec on etc.) ► If the error message returned after the appropriate action, please contact your dealer. code description action E 02 temperature sensor out of range »... - Page 30 © 2025-01-28 VHH...
Need help?
Do you have a question about the B-Compact MB-001 and is the answer not in the manual?
Questions and answers