Marantz UD7006 Service Manual
  1. Manuals
  2. Brands
  3. Marantz Manuals
  4. CD Player
  5. UD7006
  6. Service manual
Marantz UD7006 Service Manual

Marantz UD7006 Service Manual

Super audio cd/ blu-ray disc player
Hide thumbs Also See for UD7006:
Table of Contents

Advertisement

Quick Links

Download this manual
Service
Manual
• For purposes of improvement, specifications and design are subject to change without notice.
• Please use this service manual with referring to the operating instructions without fail.
• Some illustrations using in this service manual are slightly different from the actual set.
S0534-1V07DM/DG1209
UD7006
Copyright 2012 D&M Holdings Inc. All rights reserved.
WARNING: Violators will be prosecuted to the maximum extent possible.
UD7006 /
SUPER AUDIO CD/
BLU-RAY DISC PLAYER
N1SG/N1B/U1B
S1SG/S1B
Ver. 7
Please refer to the
MODIFICATION NOTICE.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the UD7006 and is the answer not in the manual?

Questions and answers

Related Manuals for Marantz UD7006

Summary of Contents for Marantz UD7006

  • Page 1 Service UD7006 / N1SG/N1B/U1B S1SG/S1B Manual SUPER AUDIO CD/ BLU-RAY DISC PLAYER • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail. • Some illustrations using in this service manual are slightly different from the actual set.

  • Page 2: Ordering Parts

    Parts for your equipment are generally available to our National Marantz Subsidiary or Agent. ORDERING PARTS : Parts can be ordered either by mail or by Fax.. In both cases, the correct part number has to be specified.

  • Page 3: Safety Precautions

    SAFETY PRECAUTIONS The following items should be checked for continued protection of the customer and the service technician. LEAKAGE CURRENT CHECK Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check.

  • Page 4: Note For Schematic Diagram

    NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. CAUTION: Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective.

  • Page 5: Warning And Laser Safety Instructions

    WARNING AND LASER SAFETY INSTRUCTIONS WARNING WAARSCHUWING Alle IC’s en vele andere halfgeleiders zijn gevoelig All ICs and many other semi-conductors are voor elektrostatische ontladingen (ESD). susceptible to electrostatic discharges (ESD). Onzorgvuldig behandelen tijdens reparatie kan de Careless handling during repair can reduce life levensduur drastisch doen verminderen.

  • Page 6: Instructions For Handling Semi-Conductors And Optical Unit

    INSTRUCTIONS FOR HANDLING SEMI-CONDUCTORS AND OPTICAL UNIT Electrostatic breakdown of the semi-conductors or optical pickup may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.

  • Page 7: Technical Specifications

    TECHNICAL SPECIFICATIONS n Audio performance Analog audio output : Output level : 2 Vrms (10 kΩ) Signal format : NTSC, PAL Mix 2 channels output terminal : Pin-jack, 1 set Applicable discs /memory device : 7.1 channels output terminal : Pin-jack, 1 set (1) BD-Video disc : Audio output characteristics : 12 cm, 1 side, 1 layer;...

  • Page 8: Cautions In Servicing

    Refer to "MEASURING METHOD AND WAVEFORMS". When you repair the BD MECHA UNIT, you can use the following JIG. Please order to marantz Official Service Distributor in your region if necessary. Do not supply it : 2-Dimensional Bar Code Reader (DS6708 made by Symbol Co. etc.)
  • Page 9 DISASSEMBLY • Disassemble in order of the arrow of the figure of following figure. • In the case of the re-assembling, assemble it in order of the reverse of the following flow. • In the case of the re-assembling, observe "attention of assembling". • I f wire bundles are untied or moved to perform adjustment or replace parts etc., be sure to rearrange them neatly as they were originally bundled or placed afterward. Otherwise, incorrect arrangement can be a cause of noise generation. TOP COVER BD MAIN UNIT ASSY FRONT PANEL ASSY DC FAN Refer to "DISASSEMBLY Refer to "DISASSEMBLY Refer to "DISASSEMBLY 1. FRONT PANEL ASSY" 2. BD MAIN UNIT ASSY" 3. DC FAN" and "EXPLODED VIEW"...

  • Page 10: Front Panel Assy

    1. FRONT PANEL ASSY Proceeding : TOP COVER FRONT PANEL ASSY → (1) Detach the Loader Panel. Shooting direction: B (2) Disconnect the FFC cable, then remove the screws. FFC cable (3) Lift up to unhook the claws and move in the direction of arrow to gradually pull out the assembly. Shooting direction: C Shooting direction: D View from the bottom Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in FRONT PANEL ASSY.

  • Page 11: Back Panel Assy

    2. BD MAIN UNIT ASSY Proceeding : TOP COVER → BD MAIN UNIT ASSY (1) Detach the Loader Panel. Shooting direction: B (2) Disconnect the connector wires and FFC cables. FFC cable N104 FFC cable FFC cable BD MAIN UNIT ASSY FFC cable BACK PANEL ASSY (3) Remove the screws. Shooting direction: A View from the bottom...
  • Page 12 (4) Remove the screws, then remove the BD MAIN UNIT ASSY. BD MAIN UNIT ASSY BACK PANEL ASSY Please refer to "EXPLODED VIEW" for the disassembly method of MAIN PWB included in BD MAIN UNIT. 3. DC FAN Proceeding : TOP COVER → DC FAN Please refer to "EXPLODED VIEW" for the disassembly method of CD FAN. 4. POWER PWB UNIT Proceeding : TOP COVER → DC FAN POWER PWB UNIT → Please refer to "EXPLODED VIEW" for the disassembly method of POWER PWB UNIT. 5. IR PWB ASSY Proceeding : TOP COVER →...

  • Page 13: Removing Discs

    REMOVING DISCS (1) Remove the Top Cover. (2) Open the CD tray by turning the Drive gear counterclockwise. Shooting direction: D...
  • Page 14 DIAGNOSTICS OF OPTICAL PICKUP d Make failure diagnostics of the Optical Pickup as follows. q If the laser drive current (Iop) becomes more than BD : ± 6 [mA], DVD or CD : ±12 [mA] of the initial value, the Optical Pickup should be replaced.
  • Page 15 1. Iop checked Method SelecttheLaseron/off(CD/DVD/BD)modeofthetestmode,andchecktheIOPvalueofCDlaser,DVDlaserorBD laser.(Referto"6.Testmode") FL Display (The display part of 13 digits) L a s e r O n O f f Laser current check Press the 8 or 9 button to display the laser current value, and then select [X]. Check the current value of Iop (nnnn) FL Display (The display part of 13 digits) T 2 X : m m m m : n n n n...
  • Page 16 (Part No. : 963309100060S) 1. How to Replace the BD MAIN UNIT (including the MAIN PWB UNIT) (1) Refer to the removal procedure, and remove and replace the BD MAIN UNIT(UD7006). (see "DISASSEMBLY") (2) F ollow the firmware update procedure, and update the firmware to the latest version. (see "VERSION UPGRADE PROCEDURE OF FIRMWARE") 2.

  • Page 17: Main Pwb Unit

    [Connection] (1) Connect the PC and bar code reader. (2) Connect the 232C (TTL) side 4P PH connector of the USB - 232C (TTL) conversion jig to the MAIN PWB UNIT (CN601) of the set. (3) Connect the USB side of the USB - 232C (TTL) conversion jig to the PC. USB - 232C(TTL) conversion jig MAIN PWB UNIT 4P RE-PH CONN CORD (1000mm)
  • Page 18 (5) On the screen below, select "ComPort XX". Select the USB - 232C (TTL) conversion jig port. (6) Check "Directly".
  • Page 19 Click the left edge of the "Bar Code" window, and the cursor begins to flash. Click (8) Place the bar code reader over the bar code attached to the replacement BD MECHA UNIT ASSY. When the reader has finished reading the barcode, the read data is displayed. b If the 2-dimensional barcode data has already been read by the 2-dimensional barcode reader, and the converted data obtained, copy the data from the data file, and paste it into this section.
  • Page 20 (9) Click Write(F2). (10) When “Pass” changes to green, writing to the Flash ROM of the MAIN PWB UNIT is complete. (11) Switch off the set unit power, and remove the 232C (TTL) side 4P PH connector of the USB - 232C (TTL) conversion jig from the MAIN PWB UNIT (CN601).

  • Page 21: Optical Pick-Up

    2.4. Replace the BD MECHA UNIT ASSY (1) Remove the old BD MAIN UNIT from the set unit (see "DISASSEMBLY"). (2) Remove the MECHA COVER. MECHA COVER (3) Cut wire clamp band, then disconnect the connector wire and FFC cable. MAIN PWB UNIT FFC cable HA700...
  • Page 22 (5) Attach the BD MECHA UNIT ASSY for replacement to the set unit. (When assembling the unit, perform the steps in reverse order.) (6) Check that the 45P-FFC, 9P-FFC and 5P-PH connector cords have been connected. 2.4. Configure the settings of the set that contains the new BD MECHA UNIT (1) Check the laser amperage (see laser on/off mode in the test mode (page 26)).

  • Page 23: Service Mode

    SERVICE MODE 1. Initial setting mode 1.1. preparation (1) E quipment used: None (2) U nit setting: No spec other than the following procedure. 1.2. procedure b I nitialize the BD player when µcom, peripheral parts of µcom, or MAIN P.W.B. unit has been replaced in servicing. b A ll user setting will be lost and its factory setting will be restored when this initialization is made. Be sure to memorize your setting for restoring again after the initialization. (1) T urn on this model's power. "NO DISC" is displayed on the fluorescent tube. (2) P ress the this model's 2 and SOUND MODE buttons simultaneously. "INITIALIZING" is displayed on the fluorescent tube. (3) T he display on the fluorescent tube switches to "INITIALIZED", the "NO DISC" display reappears and initialization is completed. 2. Firmware version check mode 2.1.

  • Page 24: Remote Lock Mode

    (1) Pressing the PURE DIRECT and 3 buttons for simultaneously. (2) “Lock-On” is displayed on the FL tube, and operations with the remote control and the REMOTE CONTROL input terminal on the back of the UD7006 are disabled. [Cancel] (1) Pressing the PURE DIRECT and 3 buttons for simultaneously.

  • Page 25: Entering The Test Mode

    6. Test mode f 6.1. Entering the test mode The test mode is entered by pressing the 5 and 3 buttons simultaneously, plug the AC cord into a power outlet. When the test mode is set, the " 1 " and " 3 " indicators light. FL tube display when test mode entered FL Display (The display part of 13 digits) When the test mode is set, the choice screen of the mode appears on the monitor.
  • Page 26 6.3. About each mode ・ With the mode selected, press the 1 button to set that mode. (1) Laser on/off (CD/DVD/BD) mode Press the 8 or 9 button to select [X] and press the 1 button to set it. Laser on/off control is executed and the laser current is displayed. FL Display (The display part of 13 digits) (X=1 : CD laser mode, 2 : DVD laser mode, 3 : BD(SL) laser mode) (mmmm[mA] : Stored data, nnnn[mA] : Current value) b W hen the current value is more that BD: ±6[mA], DVD or CD: ± 12[mA] of saved data, it becomes the pickup transducer's target. In this case, replace the mechanism unit. When the 2 button is pressed, the layer above the current layer is displayed. See "6.4 Stopping the mode". (2) Error rate measurement mode Press the 8 or 9 button to select [YY] . Refer to [Table 1 - Error rate details]. FL Display (The display part of 13 digits) (YY : measurement mode, F : Address and error rate (When not set, "F" is displayed.)) Press the 1 button to begin error rate measurement. The address and error rate are displayed. For a description of the displayed measurement results, see "Table 1: Error rate details".
  • Page 27 (3) Accumulated laser on time display mode Press the 8 or 9 button to select [Y] and press the 1 button to set it. The accumulated laser on time is displayed. FL Display (The display part of 13 digits) (Y=1 : CD, 2 : DVD , 3 : BD, mmmmmm : Time(Fractions of hours are counted up one hour on the display.)) When the 2 button is pressed, the layer above the current layer is displayed. See "6.4 Stopping the mode". ---To clear the accumulated laser on time--- Press the 1 button while the accumulated laser on time is displayed ("TC1, "TC2", "TC3" ) until "TC4 ＊ clear??" appears at the display. FL Display (The display part of 13 digits) If the 1 button is pressed, the accumulated laser on time of CD, DVD and BD is cleared. FL Display (The display part of 13 digits) When "TC1", "TC2" or "TC3" is selected with the 8 or 9 button, "mmmmmm" is displayed as "0" so you can check. (4) Picking up No. display mode Press the 8 or 9 button to switch to the pickup number display. The pickup number is a 15-digit number, so it is displayed in two sections.
  • Page 28 6.4. Stopping the mode When the 2 button is pressed, the layer above the current layer is displayed. The relationship between the different modes and the display of the different layers is shown on the table below. Mode 1 layer 2 layer 3 layer Laser on/off (CD/DVD/BD) mode T2 LaserOnOff T2X mmmm nnnn Error rate measurement mode T7 Error Rate TYYFFFFFFFFFF TYYmmmmmmllll Accumulated laser on time display mode TC LaserOnTim TCY mmmmmmh TC4* clear?? Picking up No. display mode TG OPU Number TGX YYYYYYY Test mode cancel TI Test Exit TI1 Really? 6.5. About the OPEN/CLOSE ( 5 )button Even during the test mode, the tray is opened and closed when the 5 button is pressed. 6.6.

  • Page 29: Measurement Position

    Error rate display details for each media type Measurement Remarks position The inner It is invalid. It is invalid. It is invalid. When this is selected for BD, DVD or circumference of CD, T84 FFFFFFFFFF display. 2-layer The inner LDC error detection PI error detection It is invalid. When this is selected for 1-layer DVD circumference of signed number number or CD, T85 FFFFFFFFFF display. 2-layer The inner It is invalid. It is invalid. It is invalid. When this is selected for BD, DVD or circumference of CD, T86 FFFFFFFFFF display. 2-layer The central BIS error detection It is invalid. It is invalid.

  • Page 30: Update From The Internet

    PROCEDURE FIRMWARE FOR UPGRADING THE VERSION OF THE FIRMWARE You can update by downloading the latest version from the Internet. 1. Update from the Internet 1.1. preparation (1) System requirements • Internet Connection by Broadband Circuit • Modem • Router •...

  • Page 31: Troubleshooting

    TROUBLE SHOOTING 1. POWER UNIT The power cannot be turned on. Defect of primary circuit component. (RBV1506) ・[D101] (STR-W6753) ・[U102] Check FUSE condition. (STR-A6059H) ・[U103] [F101] ・FUSE (AEP-ERL28075 (SW_TRANS)) ・[T101] (AEP-EE16202 (SW_TRANS)) ・[T102] and other circuits. Check parts and soldering. (STR-A6059H) ・[U103] Check 5.5V_STBY output.

  • Page 32: Display Unit

    2. DISPLAY UNIT 2.1. FL TUBE doesn't light. Check parts (surrounding) and soldering. (MR-6625UYB) ・[U3] ・[J1] (20x1/W/HOUSING) Check ±F output.（4.8V） POWER UNIT (J1 #14 - #16) ・[T101] (AEP-ERL28075 (SW_TRANS)) ※ 4.32V ～ 5.28V (FS34) ・[D115] ・[N101] (20P-FMN) and other circuits. Check parts (surrounding) and soldering.
  • Page 33 3. MAIN UNIT 3.1 Video out doesn't output. ・Check soldering (U702, U20). Check power supply. ・ Check the power supply voltage of ・Check the power supply (+5V_AV) of U20. U702(1pin(+12VA)). Check input signal to [U20]. ・ Check soldering (U20, U100, U20(1pin and 6pin) ・Is data input to 6pin? and surrounding circuitry).
  • Page 34 3.2. Component out doesn't output. Check power supply. ・ Check the power supply (1.0V_ABT, 1.8V_ABT, +3.3V_V) of U22. ・ Check soldering (U7, U13, U17, U702 and ・ Check the power supply (+3.3V_DDST) of U225. surrounding circuitry). ・ Check the power supply (+1.8V_VIDEO, +3.3V_V) of U228.
  • Page 35 3.3. HDMI out doesn't output. Check power supply. ・ Check the power supply (1.0V_ABT, 1.8V_ABT, +3.3V_V) of U22. ・ Check soldering (U7, U13, U17, U702 and ・ Check the power supply (+3.3V_DDST) of U225. surrounding circuitry). ・ Check the power supply (+1.8V_VIDEO, +3.3V_V) of U228.
  • Page 36 3.4 Digital Out(COAX) doesn't output. Check soldering. Repair soldering. ・[C868][R868][R866][Q212][R862][R864][R863] Check the POWER UNIT. ・[R869][FB861] Check output signal. Replace the MAIN UNIT. ・[FB861] Check the digital signal for 3Vpp. Replace [C868][R868][R866][Q211][R862][R864] [R863][R869]. 3.5. Ether is not connection. Check the input signal of [U901]SMSC8710. Replace the MAIN UNIT.

  • Page 37: Audio Unit

    4. AUDIO UNIT 4.1. Audio doesn't output. Check Power supply and connection to POWER ・Check soldering (U9-12 surrounding). UNIT. ・ Check N1 : 5P PH, 1pin (+12V), 3pin(-12V). input ・ Check the local power source, U11 (+9V), from POWER UNIT. U12(-9V), U9(+5V), U10 (+3.3V) output normally? ・Check cable insertion.

  • Page 38: Measuring Method And Waveforms

    MEASURING METHOD AND WAVEFORMS To check the waveforms on the Main P.W.B., the GND (-) probe of the oscilloscope to t “CE30” point. Measuring Disc: BLX-104 (Blu-ray disc) Playback Content: Title 1 , chapter 1 Color Bar 100% (Main Menu → 59.94Hz 1080i 1.Video signal → 1.Color Bar 100%) Component output resolution: 1080i (It is better to use wires for extending between the probe and test points.)
  • Page 39 q U20 (NJM2566)_Video out_signal (C32) Video out_signal Video out_signal w - r U20 (NJM2566)_Component out_Y/Cb/Cr signal (Y:C29, Cb:C30, Cr:C31) Component out_Y signal Component out_Cb signal Component out_Y signal Component out_Cr signal Component out_Cb signal Component out_Cr signal...
  • Page 40 Terminal output check UD7006 Oscilloscope 75ohm Load Video Out terminal check Video out_signal Video out_signal Component Out terminal check Component out_Y signal Component out_Cb signal Component out_Y signal Component out_Cr signal Component out_Cb signal Component out_Cr signal...
  • Page 41 BLOCK DIAGRAM BD Core Block(F/E,B/E) Ethernet Block MAIN PWB MPEG DECORDER BD / DVD / CD 10/100 [MT8530] Ethernet DRIVE UNIT ETHERNET Transceiver [SMSC8710] FE CONT BD / DVD / CD Mech SPDIF SPDIF DIGITAL OUT RF Signal AACS CPPM CPRM Pick up Re-Encode...
  • Page 42 WIRING DIAGRAM UD7006 DISPLAY UNIT Wiring Diagram USB UNIT F-9332H SUB POWER DRIVE MECHA UNIT UNIT PH- PH P1.0 9P FFC 47P FFC 5P PH BtoB BtoB P1.0 P0.5 HA700 J700 HA600 MAIN UNIT AUDIO UNIT P1.0 POWER UNIT PH- PH J306 P1.0...

  • Page 43: Printed Wiring Boards

    PRINTED WIRING BOARDS MAIN (COMPONENT SIDE) 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
  • Page 44 MAIN (FOIL SIDE) 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
  • Page 45 DISPLAY (COMPONENT SIDE) USB (COMPONENT SIDE) POWER (COMPONENT SIDE) D112 C105 JV20 D113 Z101 C101 C106 D115 (Sec.) (Pri.) R115 JV41 R149 D118 12.5 15.0 JV47 D117 15.0 JV40 D101 JV34 12.5 F2AH250V C108 F101 C117 JV65 C109 JV43 D127 12.5 JV42 JV48...
  • Page 46 USB- (FOIL SIDE) DISPLAY (FOIL SIDE) POWER (FOIL SIDE) C173 R123 R122 R121 R137 R141 R143 D125 (Sec.) C145 (Pri.) R129 C162 C134 C163 C157 R103 R104 C158 R108 R101 R102 C111 R139 R136 R135 R110 C147 R109 R133 R145 C171 R119 R120...
  • Page 47 IR (COMPONENT SIDE) SUB POWE (COMPONENT SIDE) JV112 JV118 8U-310101-1 SUB POWER BOARD JV116 12.5 JV117 12.5 8U-110115-2 C226 IR UNIT JV102 15.0 JV120 JV115 D3 D4 JV121 D207 D205 D208 D206 D204 JV103 JV108 12.5 JV110 K202 K201 JV119 K203 B201 S201...
  • Page 48 IR (FOIL SIDE) SUB POWE (FOIL SIDE) R217 R218 L204 R220 R219 R214 C227 U201 R209 SUB POWER BOARD R207 R213 R202 Q202 BD-100109 01 R201 C220 C221 R203 D202 D203 C206 C205 C204 Q204 D201 R211 R215 C228 AUDIO (FOIL SIDE) 鉛フリー半田...

  • Page 49: Schematic Diagrams

    LED_A LED_B 8U-110115-1 R135 R136 W_REMOTE POWER UNIT 0.5% +12V 5.5V_STBY Z114 HEAT_SINK KEY_INA R128 653010055005S VFD_STB 1.5K C169 (MQ.0242-A-D) VFD_CLK C170 U101 T101 D122 VFD_DATA D114 (2/2) GND1 AEP-ERL28075 -32V TL431ACLP FMEN-210A SW_TRANS C171 L106 MOTOR+12V L.FILTER_50mH_1.5A K101 F101 L105 C166 L103...
  • Page 50 8 R2IN R2OUT C217 OPEN N201 12P-FFCs W_REMOTE. W_REMOTE. RS232C_IN RS232C_OUT AMX_POWER SET1 SET2 SET3 SET4 +5V_NSW +5V_NSW Destination Setting Reference UD7006 UD7006 UD7006 UD7006 UD7006 UD7006 UD7006 /U1B /N1B /N1SG /R1B /S1B /S1SG R216 R218 R220 R222 R224 SCHEMATIC DIAGRAMS (2/26)
  • Page 51 OPEN BLM18PG330SN1D BLM18PG330SN1D 6.2M GND2 1SS355 MP2208DL LF-Z 1000P 0.01 100K OPEN 0.01 0.1Z BLM18PG330SN1D GND2 3.3uH 1608 47/16 47/16 2125 (C6K5LGA) 1608 100K OPEN GND2 0.1Z GND2 OPEN BLM18PG330SN1D BLM18PG330SN1D GND2 6.2M 1SS355 MP2208DL LF-Z 1000P 0.01 100K OPEN 0.01 BLM18PG330SN1D 0.1Z...
  • Page 52 MR-6625UYB MR-6625UYB STBY_KEY V+VFD KEY_IN_B VCC_3.3V V+VFD GR12 GR11 V-VFD GR10 LED1 LED1 LED2 LED2 ON/STANDBY FL OFF -32V 100R 100R VFD_DATA 100R 100R VFD_CLK 100R 100R VFD_STB SG20 SG20 KEY_IN_A 2.7k 3.3k 5V_STBY SG19 SG19 IR_IN GR13 W_REMOTE SG18 GR14 SG18 LED_B...
  • Page 53 +3.3VD PCM_DSD# +3.3VD PCM_DSD H:PCM MODE L:DSD MODE AUDIO SHEET 1/3 PCM_DSD AOMCLK DTC114EK DGND 2 1A PCM_DSD# AOBCK (MIX L/R BLOCK) AOLRCK 3 1B AOSDATA4 5V_STBY 4 1Y AOLRCK 5 2A PCM1795_PIN4_LRCK_SDATA AOSDATA3 AOBCK [to U201(SL/SR)(sht 3/3)] 6 2B DGND 7 2Y PCM1795_PIN6_BCK...
  • Page 54 TPF66 Q105 DTA114EK TPF67 TPF68 AUDIO SHEET 2/3 Q107 DTC114EK R112 (7.1ch BLOCK FL/FR/C/SW) TPF69 C115 R119 AGND 1000P Q106 AGND DTA114EK C127 R102 R106 R111 TPF70 2200P TPF71 U102 +3.3VD +5VA U104 NJM4565M NJM4565M Q108 U101 R115 820 AGND DTC114EK PCM1795DBR C114...
  • Page 55 TPF80 Q205 DTA114EK TPF79 TPF78 AUDIO SHEET 3/3 Q207 DTC114EK R216 (7.1ch BLOCK SL/SR/SBL/SBR) TPF83 C215 AGND R223 Q206 1000P AGND DTA114EK C227 R206 R210 R215 TPF82 2200P TPF81 U202 +3.3VD +5VA Q208 NJM4565M DTC114EK U201 R219 820 AGND PCM1795DBR C214 U204 DGND...
  • Page 56 A_KEY_IN R384 R384 BLM15P BLM15P FB27 FB27 KEY_IN_A B_KEY_IN R383 R383 BLM15P BLM15P FB26 FB26 KEY_IN_B C1032 C1032 IR_IN IR_IN [19] PWR_AC_DET C1034 C1034 KEY_IN_B AC_DET AC_DET KEY_IN_B [19] PS_ON KEY_IN_A PS_ON PS_ON KEY_IN_A [19] STB_KEY W_REMOTE STB_KEY STB_KEY W_REMOTE [19] 100pF/NC 100pF/NC...
  • Page 57 1.8V U101 U101 U102 U102 U100A U100A A_DQ13 A_RA0 A_DQ16 A_RA0 A_DQ9 A_RA1 A_DQ22 A_RA1 1.8V C101 C101 C102 C102 C103 C103 C104 C104 C105 C105 C106 C106 C107 C107 A_DQ8 A_RA2 A_DQ21 A_RA2 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.1uF/16V...
  • Page 58 U100B U100B U201 U201 U202 U202 B_DQ0 B_RA0 B_DQ18 B_RA0 B_DQ0 B_DQ4 B_RA1 B_DQ20 B_RA1 AR39 DVSS B_DQ0 B_DQ1 B_DQ2 B_RA2 B_DQ23 B_RA2 AW43 DVSS B_DQ1 B_DQ2 B_DQ1 B_RA3 B_DQ19 B_RA3 AU43 DVSS B_DQ2 1.8V B_DQ3 B_DQ6 B_RA4 B_DQ17 B_RA4 AU41 DVSS B_DQ3...
  • Page 59 FB200 FB200 1.2V BLM15P BLM15P U100C U100C 1.2V HW TRAPPING AVDD12_APLL FB206 FB206 AVDD12_HDMI C951 C951 BLM15P BLM15P NFREN NFREN [5,6] C927 C927 C952 C952 C953 C953 BE 1.2V:Below 0.1A NFWEN NFWEN [5,6] 0.1uF 0.1uF 10uF/10V 10uF/10V 0.1uF 0.1uF NFALE NFALE [5,6] 3.3V_VDAC...
  • Page 60 HW TRAPPING NAND 3.3V U100E U100E NFREN NFREN FLASH NFWEN NFWEN TP304 TP304 1.2V NFALE NFALE SFCS AVDD12_STX1 FB308 FB308 BLM15P BLM15P NFCLE 0402 SFCS AVDD12_STX1 NFCLE SFCK AVDD12_SRX1 FB301 FB301 BLM15P BLM15P SFCK AVDD12_SRX1 SFDI BE 1.2V:Below 0.1A NFCEN NFCEN SFDI AVSS12_ST1...
  • Page 61 U100D U100D VCC3IO_STB 3.3V VCC3IO_STB1 FB400 FB400 Trapping BLM15P BLM15P ETCOL ETCOL [11] VCC3IO_STB1 ETCOL ETCRS VCC3IO_STB ETCOL ETCRS [11] C403 C403 C404 C404 ETCRS Close to 0402 VCC3IO_STB ETCRS 3.3V_STBY 4.7uF/NC 4.7uF/NC 0.1uF 0.1uF ETMDC (Test Mode) ETMDC VCC3IO_STB:Below 20mA ETMDC ETMDC [11]...
  • Page 62 U100F U100F 1.1V 1.1V 3.3V R554 R554 VOUTVSYNC VCCK VOUTVSYNC V500 V500 R555 R555 VOUTHSYNC AB20 VCCK VOUTHSYNC V501 V501 C537 C537 C538 C538 C523 C523 C526 C526 AD20 VCCK 10uF 10uF 0.1uF 0.1uF 4.7uF 4.7uF 4.7uF 4.7uF R556 R556 VOUTCLK1 EFVDDQ_CTL TP732...
  • Page 63 BEFE_EX M3.3V GIO14 /TRST FB604 FB604 AVCC AVCC A1.2V GIO19 BLM18P BLM18P M3.3V GIO16 FE_RXIN FE_RXIN D3.3V GIO17 R648 R648 FE_RXIP FE_RXIP RTCK A3.3V C996 C996 GIO18 R649 R649 0.1uF 0.1uF C713 C713 C714 C714 GIO15 R652 R652 TGIO15 TGIO15 C691 C691 C690...
  • Page 64 MOTOR DRIVER GAINSW2 MOTOR GAINSW2 [8] MUTE2 MUTE2 V14REF R700 R700 R702 R702 MUTE1 MUTE1 DRIVER MOTOR R701 R701 R704 R704 V14REF TRAYPWM R703 R703 R705 R705 DRIVER TRAYPWM FB701 FB701 U700 U700 R706 R706 DMSO V14REF V14REF DMSO POWER BLM21P BLM21P DMSO...
  • Page 65 AUDIO CNT GND9 GND9 R398 R398 AOMCLK PCM_DSD# AOMCLK AOMCLK PCM_DSD# [5,16] R397 R397 AOBCK AMUTE AOBCK AOBCK AMUTE [4,6] HA701 HA701 +12VA +12VA R423 R423 AOLRCK AOLRCK AOLRCK AUDIO I2S R1248 R1248 +12VA GND10 GND10 R394 R394 AOSDATA0 AOSDATA0 AOSDATA0 R1249 R1249...
  • Page 66 LAN-3.3V LAN_VDDA LAN-3.3V LAN_VDDA FB903 FB903 ETMDC ETMDC ETMDIO R931 10 R931 10 ETMDIO BLM18P BLM18P ETTXCLK ETTXCLK C975 C975 C976 C976 C977 C977 C978 C978 C979 C979 ETTXD0 ETTXD0 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10uF 10uF 0.1uF/16V 0.1uF/16V ETTXD1 PWFBOUT PWFBOUT...
  • Page 67 3.3V_ABT RP24 RP24 ABT2015_Y11_R 4x47R 4x47R ABTO_Y11_F3 U22A U22A ABT2015_Y10_R ABTO_Y10_H2 ABT2015_Y9_R ABTO_Y9_G3 ABTO_CLK_H5 [15] ABTO_CLK_H5 VOUT9 CCIR_OUT_Y9 ABT2015 ABT2015 ABT2015_Y11_R ABT2015_Y8_R ABTO_Y8_H1 VINY9 VOUTY11 VOUT8 CCIR_OUT_Y8 ABT2015_Y10_R RP25 RP25 VINY8 VOUTY10 VOUT7 CCIR_OUT_Y7 ABT2015_Y9_R ABT2015_Y7_R 4x47R 4x47R ABTO_Y7_H3 [15] ABTO_VS_N2 ABTO_VS_N2 VINY7...
  • Page 68 +3.3V_V 3.3V_ABT 1.8V_ABT 1.0V_ABT U22C U22C 0.1uF/16v 0.1uF/16v 0.1uF/16v 0.1uF/16v 0.1uF/16v 0.1uF/16v 0.1uF/16v 0.1uF/16v 0.1uF/16v 0.1uF/16v 0.1uF/16v 0.1uF/16v 0.1uF/16v 0.1uF/16v BLM21P BLM21P 0.1uF/16v 0.1uF/16v BLM21P BLM21P ABT2015 ABT2015 0.1uF/16v 0.1uF/16v C340 C340 C323 C323 C326 C326 C347 C347 C335 C335 C342 C342 C337...
  • Page 69 DDR2_DQ[31..0] DDR2_A[12..0] DDR2_DQ[31..0] [13] DDR2_A[12..0] DDR2_DQ[31..0] [13] DDR2_A0 DDR2_DQ0 DDR2_A0 DDR2_DQ16 DDR2_A1 DDR2_DQ1 DDR2_A1 DDR2_DQ17 [13] DDR2_CLK[1..0] DDR2_A2 DDR2_DQ2 DDR2_A2 DDR2_DQ18 DDR2_CLK0 DDR2_A3 DDR2_DQ3 DDR2_A3 DDR2_DQ19 DDR2_CLK1 DDR2_A4 DDR2_DQ4 DDR2_A4 DDR2_DQ20 DDR2_A5 DDR2_DQ5 DDR2_A5 DDR2_DQ21 [13] DDR2_CLK_N[1..0] DDR2_A6 DDR2_DQ6 DDR2_A6 DDR2_DQ22 DDR2_CLK_N0 DDR2_A7...
  • Page 70 +3.3V_DDST +3.3V_DDST TO SiI9134 U225B U225B U225A DOHM_Cr10_A2 DOHM_Y2_D11 R113 R113 IO_B2_A2 IO_B2_D11 ABTO_B7_C2 ABTO_CbCr1_P2 DOHM_Cr6_A4 DOHM_Cb10_D12 IO_B1_C2 IO_B1_P2 IO_B2_A4 IO_B2_D12 DOHM_Cr11_C3 DOHM_Cr2_A5 DOHM_Cb5_D13 IO_B1_C3 IO_B1_P4 IO_B2_A5 IO_B2_D13 ABTO_B9_D1 DOHM_Y10_A6 IO_B1_D1 IO_B1_P5 IO_B2_A6 IO_B2_D14 1HTPCK [16] ABTO_B10_D2 TEST20_P6 DOHM_Y7_A7 DOES_OEn_D15 DOHM_CLK_A10 R164 R164...
  • Page 71 1HTPCK [15] 1HTPCK GND4 GND4 U25A U25A HDMITX1_AVCC18 CN19 CN19 1HTVSYNC [15] 1HTVSYNC 1HTHSYNC [15] 1HTHSYNC SHELL1 R724 R724 R587 R587 680R/1% 680R/1% Set the resistor 1HTDE [15] 1HTDE RST_HDMITX1_N GND2 GND2 RESET# EXT_SWG SHELL2 on top layer HDMI1_TX2+ HDMI1_TX2+ 1HTG0 [15] 1HTG0...
  • Page 72 +1.8V_VIDEO +3.3V_V TO MCU +3.3V_V +1.8V_VIDEO 10uH 10uH VCC_P_V_V IIC I/F R491 NC R491 NC [5,10,12,16,19] +5V_VV [5,10,12,16,19] R492 NC R492 NC C459 C459 C442 C442 C503 C503 C441 C441 C502 C502 C440 C440 C437 C437 C527 C527 C443 C443 + C18 + C18 + C16...
  • Page 73 U702 U702 VCC_P_V AZ1117-ADJ AZ1117-ADJ ASPDIF +12VA R740 0 R740 0 R742 R742 R743 R743 COMP_Y COMP_Y [17] COMP_Pb_Cb CE38 + CE38 COMP_Pb_Cb [17] R862 R862 R167 R167 R741 0 R741 0 FB861 FB861 R863 2.2K R863 2.2K COMP_Pr_Cr 1.8K 1.8K CE20 CE20...
  • Page 74 TO MT8530 PIN FB18 FB18 BLM18P BLM18P IIC ISP Interface MCU_2.5V MCU_3V3 MCU_3V3 MCU_3.3V MCU CS8966F GPIO LIST FB21 FB21 BLM15P/NC BLM15P/NC CCIR_IN_Y9 CCIR_IN_Y9 5V_STBY NAME FEATURES AND NET MCU_3.3V 0.1uF/16V 0.1uF/16V MCU_IIC_SDA MCU_3.3V R289 R289 KEY_IN_B MCU_IIC_SDA MCU_IIC_SDA 1SS355 1SS355 R290 R290...
  • Page 75 EXPLODED VIEW f WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.  印の部分は安全を維持するために重要 な部品です。従って交換時は必ず指定の 部品を使用してください。...
  • Page 76 Personal notes: Personal notes:...
  • Page 77 DISPLAY PWB UNIT ASSY 7025HV1003212 USB PWB UNIT 972632000040S AUDIO PWB UNIT ASSY 7025HV1004012 CHASSIS 3200213776100S 4007210651000S 972304000530S BD MAIN UNIT(UD7006) 7025HV1005010 MAIN PWB UNIT 963309100060S BD MECHA UNIT ASSY 8038041679010S 45301003200AS CLAMPER ASS'Y for BD MECHA (F-9332H) MZ11-138 ★ 67 9P FFC(1.0)
  • Page 78 FRONT PANEL ASSY(UD7006/B) 972402000330M FRONT PANEL ASSY(UD7006/SG) SPACER (D7.5X3.5XT1.0) 1530210302000S FRONT PANEL(7006BK) 3067215188100S FRONT PANEL(7006SG) 3067215188120S MARANTZ BADGE (AL) FOR M1 MODEL 5630210678000S INNER PANEL (5005BK) CENTER 3067215151200S INNER PANEL (5005SG) CENTER 3067215151300S BLIND SHEET(5005) 4050213389000S GASKET SHEET (5005) LEFT...

  • Page 79: Parts List Of P.w.b. Unit

    Ref. No. Part No. Part Name Remarks Q'ty WIRES ★ 60 00MYU12090520 12P FFC N711120833810S ★ 61 00MYU15080520 15P FFC N711150833810S ★ 62 5P CON. L002261050050S ★ 63 13P CON. L002201130050S ★ 64 00MYU20100520 20P FFC N711201033810S ★ 65 00D0090252062 27P FFC N711270933810S ★...

  • Page 80: Packing View

    PACKING VIEW...

  • Page 81: Parts List Of Packing View

    L063152030020S TWIN SHIELDED WIRE WITH RCA PLUGS L063102010110S BATTERY(R03X2) G670001R50220S 307010078008M RC005UD REMOCON UNIT C.G.DEVELOPMENT 8300005000010S 972531000390M CARTON CASE (UD7006) 6007211830050S CONT. LABEL (7006/U1B) SUB ASSY 5507000007500S CONT. LABEL (7006/N1B) SUB ASSY 5507000007500S CONT. LABEL (7006/N1SG) SUB ASSY N1SG 5507000007500S CONT.

  • Page 82: Terminal Function

    SEMICONDUCTORS Only major semiconductors are shown. Genaral semiconductors etc. are omitted from list. The semiconductors which have a detailed drawing in a schematic diagram are omitted from list. 1. IC's CS8966-PQFP44 (MAIN UNIT : U16) VDD25 P1.2 / SDA / SWC0 P1.3 / SCL / SWC1 RSTN P1.4 / SWC2 P2.4 / T2EX / CMPD...

  • Page 83: Block Diagram

    I/O Port Definition Port Assignment Function PU/PD Function Description Name I/O Normal I2C Data signal that comunicate with MT8530. P1.2 MCU_IIC_SDA High(3.3V) Hi-Z 4.7K PU SW3.3V (Slave mode). High(3.3V)/50Hz High(3.3V)/50Hz P1.1 AC_DET 10k PU Detection signal is for AC power. or 60Hz pulse or 60Hz pulse P1.0 Not use Hi-Z Hi-Z...
  • Page 84 PT6302 (DISPLAY UNIT : U5) Terminal Function Pin Name Description Pin No. SG5 to SG35 1 ~ 31 Segment driver output pin SG4 to SG1 64 ~ 61 l l i l l i Reset input pin RSTB When this pin is set to "LOW", all functions are initialized. Chip select input pin When this pin is set to "High"...
  • Page 85 MT8530 (MAIN UNIT : U100) Block Diagram HDMI, CVBS, Component Motor USB 2.0 Driver MT8530 Ethernet Audio DAC FLASH DRAM...
  • Page 86 LAN8710 (MAIN UNIT : U901) Block Diagram...
  • Page 87 NJM2566AV (MAIN UNIT : U20) Block Diagram...
  • Page 88 DVD-3930/3930CI DVD-3930/3930CI PCM1796DBR (AU: IC401, 406, 411, 702, 707) PCM1796DBR (AU: IC401, 406, 411, 702, 707) PCM1795DBR (AUDIO UNIT : U1, U101, U111, U201, U211) (TOP VIEW) (TOP VIEW) ZEROL ZEROL ZEROR AGND3L ZEROR AGND3L MSEL L− MSEL L− LRCK LRCK DATA AGND2 DATA AGND2 DGND DGND AGND1 AGND1 R−...
  • Page 89 DVD-3930/3930CI PCM1796DBR Terminal Function Terminal Function TERMINAL DESCRIPTIONS DESCRIPTIONS NAME AGND1 − Analog ground (internal bias) AGND2 − Analog ground (internal bias) AGND3L − Analog ground (L-channel DACFF) AGND3R − Analog ground (R-channel DACFF) Bit clock input (1) Serial audio data input (1) DATA DGND −...
  • Page 90 HIN202EIBNZ-T (IR POWER UNIT : U201) 0.1µF +5V TO 10V 0.1µF VOLTAGE INVERTER +10V TO -10V 0.1µF VOLTAGE INVERTER 0.1µF 400kΩ 400kΩ 5kΩ 5kΩ...
  • Page 91 2. FL DISPLAY FL TUBE (15-BT-114GNK) (Display UNIT: U3)

  • Page 92: Personal Notes

    Personal notes:...

This manual is also suitable for:

Ud7006/n1sgUd7006/n1bUd7006/u1bUd7006/s1sgUd7006/s1b

Table of Contents