Husqvarna Rider 316T AWD Operator's Manual
Husqvarna Rider 316T AWD Operator's Manual

Husqvarna Rider 316T AWD Operator's Manual

Hide thumbs Also See for Rider 316T AWD:
Table of Contents

Advertisement

Quick Links

Oper ator ' s manual
Rider 316T
Rider 316T AWD
Rider 316Ts AWD
Rider 316TXs AWD
E E E E n n n n g g g g l l l l i i i i s s s s h h h h
Please r ead the operator's manual carefully and make sure you understand the
instructions before using the machine.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Rider 316T AWD and is the answer not in the manual?

Questions and answers

Summary of Contents for Husqvarna Rider 316T AWD

  • Page 1 Oper ator ′ s manual Rider 316T Rider 316T AWD Rider 316Ts AWD Rider 316TXs AWD E E E E n n n n g g g g l l l l i i i i s s s s h h h h Please r ead the operator’s manual carefully and make sure you understand the...
  • Page 2: Table Of Contents

    CONTENTS Contents Ignition system ............. Check the safety system ..........CONTENTS Replacing the light bulbs ..........Contents ..............Main fuse ..............Service journal Checking the tyre pressure .......... Pre-delivery service ............. Checking the engine’s cooling air intake ...... After the first 8 hours ........... Fitting the cutting head ..........
  • Page 3: Service Journal

    Service journal Pre-delivery service 12 Tell customer about: Needs and benefits of following the service 1 Charge the battery for at least 4 hours at max. 5 schedule. amp. Servicing and the influence of this journal on the 2 Fit steering wheel, seat and any optional second-hand value of the machine.
  • Page 4: Introduction

    Dear Customer, Thank you for choosing a Husqvarna Rider. Husqvarna Riders are built to a unique design with a front-mounted cutting unit and a patented articulated steering. Riders are designed for maximum efficiency even in small or confined areas. The closely grouped controls and pedal-operated hydrostatic transmission also contribute to the performance of this machine.
  • Page 5: Key To Symbols

    KEY TO SYMBOLS Symbols Noise emission to the environment according to the European Community’s Directive. The machine’s emission is These symbols are on the machine and in the instructions. specified in the Technical data chapter and on the label. WARNING! Careless or incorrect use can result in serious or fatal injury to the Clutch in operator or others.
  • Page 6: Explanation Of Warning Levels

    KEY TO SYMBOLS Explanation of warning levels Switch off the engine and take off the ignition cable before repairs or maintenance The warnings are graded in three levels. WARNING! Before and during reversing procedures, look behind you. WARNING! Used if there is a risk of serious injury or death for the operator or damage to the surroundings if the instructions in the manual are not followed.
  • Page 7: What Is What

    WHAT IS WHAT? 11 12 What is what on the ride-on mower 1 Speed limiter for driving forward 10 Cover lock 2 Speed limiter for reversing 11 Parking brake 3 Lifting lever for the cutting unit 12 Lock button for parking brake 4 Cutting height adjustment lever 13 Seat adjustment.
  • Page 8: Safety Instructions

    SAFETY INSTRUCTIONS Safety instructions • Remember that the driver is responsible for dangers or accidents. These instructions are for your safety. Read them carefully. • Never carry passengers. The machine is only intended to be used by one person. Insure your Rider •...
  • Page 9: Driving On Slopes

    SAFETY INSTRUCTIONS Driving on slopes • Never allow children or other persons not trained in the use of the machine to use or service it. Local laws may regulate the age of the user. Driving on slopes is one of the operations where the risk of the driver losing control of the machine or of it overturning is the greatest;...
  • Page 10: Children

    SAFETY INSTRUCTIONS Maintenance • Do not try to stabilize the machine by putting your foot on the ground. • Stop the engine. Prevent the engine from starting by • When cleaning the chassis, the machine may never be removing the ignition key before making any adjustments driven near verges or ditches.
  • Page 11: Transport

    SAFETY INSTRUCTIONS • Take care with battery maintenance. Explosive gases • Reduce the risk of fire by removing grass, leaves and form in the battery. Never perform maintenance on the other debris that may have fastened on the machine. battery while smoking or in the vicinity of open flames or Allow the machine to cool before putting it in storage.
  • Page 12: Presentation

    Pedal (1) is used to drive forwards, and pedal (2) to drive backwards. The machines are equipped with chronometer and lights. Rider 316T AWD, 316Ts AWD, 316TXs AWD is equipped with all wheel drive. Rider 316Ts AWD, 316TXs AWD is also equipped with power steering.
  • Page 13: Cutting Unit

    PRESENTATION Cutting unit Lights Rider 316T, Rider 316T AWD, 316TXs AWD and Rider 316Ts The lights are switched on and off using the power switch on AWD can be equipped with three different cutting units. the control panel. Counter •...
  • Page 14: Fueling

    The engine runs on unleaded petrol with a minimum octane rating of 87 (not mixed with oil). We recommend the use of Rider 316T AWD, 316TXs AWD and Rider 316Ts AWD have biodegradable alkylate petrol. (max. methanol 5%, max. one control for the front axle and one control for the rear axle.
  • Page 15: Driving

    Driving Before starting Start the engine • Read the safety instructions and information concerning 1 Make sure that the clutch control is depressed. Rider the placement of controls and functions before starting. 316T AWD, 316TXs AWD and Rider 316Ts AWD have one control for the front axle and one control for the rear •...
  • Page 16: Starting The Engine With A Weak Battery

    Driving 6 When the engine starts release the ignition key IMPORTANT! Your Rider is equipped with a 12-volt system immediately back to neutral position. with negative earth. The other vehicle must also have a 12- volt system with negative earth. Do not use your Rider battery to start other vehicles.
  • Page 17: Driving The Rider

    Driving Driving the Rider 4 Press in the lock button on the lifting lever and lower the cutting unit. 1 Release the parking brake by first pressing down the parking brake pedal and then releasing it. 2 Carefully press down one of the pedals until the required IMPORTANT! speed is obtained.
  • Page 18: Maintenance

    Maintenance Maintenance schedule WARNING! No service procedures must be conducted on the engine or cutting unit unless: The engine is switched off. The parking brake is applied. The ignition key is removed. The cutting unit is disengaged. The ignition cables are removed from the plugs. The following is a list of the maintenance which should be conducted on the machine.
  • Page 19: Cleaning

    Maintenance Cleaning Right-hand fender Remove the accelerator knob (1), screws (2 and 3), and Clean the machine directly after use. It is much easier to wash remove the cover. off grass cuttings before they dry. Left-hand fender IMPORTANT! Always park the machine on a level surface Remove the screws holding the wing cover (2) and lift off the with the engine OFF before performing any maintenance.
  • Page 20: Adjusting The Parking Brake Rider 316T

    3 If necessary, the wires can be adjusted by tightening the adjuster nuts on each side of the steering collar. Rider 316T AWD, Rider 316TXs AWD Do not over tighten the cables; they should only be drawn and Rider 316Ts AWD in towards the steering collar.
  • Page 21: Checking And Adjusting The Choke Wire

    Maintenance Checking and adjusting the choke Replacing the air filter wire WARNING! The exhaust system is hot. Let it If the engine is producing black smoke or is difficult to start cool before starting to replace the air filter. then the choke wire (upper wire) may be incorrectly adjusted. If doubts arise, contact your service representative.
  • Page 22: Ignition System

    Maintenance Ignition system Replacing the light bulbs For information about the bulb type, see Technical Data. The engine is equipped with an electronic ignition system. 1 Unscrew the two screws holding the cover on the power Only the spark plug requires maintenance. servo housing.
  • Page 23: Main Fuse

    Maintenance Main fuse Checking the engine’s cooling air intake The main fuse is placed in a detachable holder under the battery case’s cover, in front of the battery. Clean the air intake grille in the engine cover behind the Type: Flat pin, 15 A. driver’s seat.
  • Page 24: Fitting The Cutting Head

    Maintenance Fitting the cutting head 6 Lift up the cutting unit WARNING! Wear protective glasses when fitting the cutting unit. The spring which tensions up the belt may break and cause personal injury. 1 Place the Rider on a flat surface and apply the parking 7 Push the unit in so that the interior plugs touch the bottom brake.
  • Page 25: Removing The Cutting Unit

    Maintenance Removing the cutting unit 3 Release the clip on the front hood and lift off the fender. WARNING! Wear protective glasses when dismantling the cutting unit. The spring which tensions up the belt may break and cause personal injury. 1 Carry out points 1-6 to put the cutting unit in the service position, see Service position for the cutting unit.
  • Page 26: Checking And Adjustment Of The Cutting Unit's Ground Pressure

    Maintenance 8 Lift the unit until it stops and a clicking sound is heard. The 5 Adjust the unit’s ground pressure by screwing in or out the unit locks automatically in the vertical position. adjusting screws located behind the front wheels on both sides.
  • Page 27: Replacing The Cutting Unit Belts

    Maintenance 4 Screw out (extend) the stay to raise the rear edge of the 3 Unscrew the bolts holding the unit frame bracket. cover. Screw in (shorten) the stay to lower the rear edge of the cover. 4 Remove the lock and pass the unit frame out. 5 Remove the two bolts on the unit frame.
  • Page 28: Checking The Blades

    Maintenance Checking the blades IMPORTANT! To achieve the best mowing results it is important that the Always exercise care and use your common sense. Avoid blades are undamaged and well-sharpened. all situations which you consider to be beyond your capability. If you still feel uncertain about operating Check that the blades’...
  • Page 29: Checking The Engine's Oil Level

    Lubrication Checking the engine’s oil level. Replacing the engine oil The engine oil should be changed the first time after 8 hours Check the oil level in the engine when the Rider stands running time. It should then be changed after every 100 hours horizontal with the engine switched off.
  • Page 30: Checking The Transmission Oil Level

    Remember to use the right screws in each mounting. Rider 316T Fill if necessary with engine oil SAE 10W/40 (class SF–CC). Rider 316T AWD, 316Ts AWD, 316TXs AWD Fill if necessary with oil Synthetic 10W/50 The oil and filter should be changed by an authorised service representative, as described in the Workshop Manual.
  • Page 31 Troubleshooting schedule Problem Cause There is no fuel in the fuel tank Faulty spark plug. Defective ignition cable. Engine does not start Dirt in the carburettor or fuel line Starter motor does not turn over the engine Defect safety switch Battery flat Bad contact between the cable and battery Lift lever for cutting unit in wrong position...
  • Page 32: Storage

    Storage Winter storage Guard At the end of the season, or if the machine is going to stand There is a cover to protect your machine during storage or idle for more than 30 days, it should immediately be made transport.
  • Page 33 Technical data Rider 316T Rider 316T AWD Dimensions Length without cutting unit, mm/ft 2020/6,61 2020/6,61 Width without cutting unit, mm/ft 890/2,92 890/2,92 Height, mm/ft 1150/3,77 1150/3,77 Machine without cutting unit, with empty tanks, kg/lb 275-280-283/606-617-624 294-299-302/648-659-666 Wheel base, mm/ft 887/2,91...
  • Page 34: Technical Data

    Technical data Rider 316Ts AWD Rider 316TXs AWD Dimensions Length without cutting unit, mm/ft 2020/6,61 2020/6,61 Width without cutting unit, mm/ft 890/2,92 890/2,92 Height, mm/ft 1150/3,77 1150/3,77 Machine without cutting unit, with empty tanks, kg/lb 307-312-315/679-688-694 294-299-302/648-659-666 Wheel base, mm/ft 887/2,91 887/2,91 Track width, front, mm/ft...
  • Page 35: Ec Declaration Of Conformity

    EC Declaration of Conformity (Applies to Europe only) Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel.: +46-36-146500, hereby declares that Husqvarna Rider 316T, Rider 316T AWD, Rider 316TXs AWD and Rider 316Ts AWD from 2012’s serial numbers and onwards (the year is clearly stated in plain text on the rating plate with subsequent serial number), complies with the requirements of the COUNCIL’S DIRECTIVE:...
  • Page 36 Original instructions 1156986-26 ´®z+X§^¶6-¨ ´®z+X§^¶6-¨ 2016-01-22 Rev.2...

Table of Contents