Related Manuals for Promax VT-109
Summary of Contents for Promax VT-109
- Page 1 VT-109 SEALER PACKAGING MACHINE TRAY Operation Manual Version 6.9.1 1915 E. Acacia Street, Ontario, CA91761, U.S.A : 1-909-923-3888 FAX : 1-909-923-3588 http://www.promarksvac.com S/N: QC SIGNATURE:...
-
Page 2: Table Of Contents
TABLE OF CONTENTS 1. PRODUCT FEATURE ................... 1 2. SUITABLE APPLICATION................... 1 3. MACHINE DIMENSIONS ..................1 4. SAFETY / WARNINGS ..................1 5. OPERATIONAL PROCEDURES ................. 2 6.PARTS ........................3 7.AVOIDANCE ......................5 8.USER MAINTENANCE..................5 9.TROUBLE SHOOTING..................7... -
Page 3: Product Feature
1. PRODUCT FEATURE 1) T h e M a c h i n e b o d y i s Stainless in nature. 2) U sing PLC control , uneasy to be broken. 3) S a f e , s a v i n g e l e c t r i c i t y , l o n g - l i f e , e a s y t o c l e a n . 4) A w i d e variety of container of different size and material can be used. -
Page 4: Operational Procedures
5.OPERATIONAL PROCEDURES 1) P o w e r i n d i c a t o r : i n d i c a t i n g t h e p o w e r i n o n l i n e o r o ff l i n e . 2) P ower off/on:press power key to start up the machine.after displaying the “PO”... -
Page 5: Parts
6.PARTS 1. Filmwind-up Motor 7. In/Out Motor 13. Regulator 2. Capacitor 8. Bolt 14. Film sensor 3. PLC 9. Back Limit switch 15. Counter sensor 4. Power switch 10. Front Limit switch 16.Bakelite rod 5. Fuse 11. In/Out shaft 17. Bakelite 6. - Page 6 1. Heater 1. Mold salver(bottom) 6. Spring 2. Temperature sensor line 2. Mold top plant 7. Bolt 3. Spring 3.Mold mast 8. Cutter mount 4. Bolt 4. Mold bottom plant 9. Mold fixed plant 5. Heat slice fixed plate 5. Mold knife 1.
-
Page 7: Avoidance
7 . A VOIDANCE 1) C h e c k t h e a l t e r n a t i n g current (AC) before plug in. 2) D o n o t u s e multi-outlet or extended-outlet with other electric appliances when using . 3) F o l l o w t h e o p e r a t i o n m a n u a l p r o c e d u r e i n o r d e r t o a v o i d m i s u s a g e o f m a c h i n e t h a t r e s u l t s i n i n j u r y a n d d a m a g e t o t h e m a c h i n e . - Page 8 Use hand to push up the air output valve, let the air leak out and release the air pressure totally. Loosen the auto-lubricator, and re-fill lubricant oil. 3) O t h e r t h i n g s t o b e c h e c k e d o r m a i n t a i n e d : t h e o p e r a t o r o f t h e m a c h i n e m a y c o n t a c t t h e r e p a i r i n g a g e n t i n t h e i r a r e a o r c o - o p e r a t e w i t h t h e r e p a i r i n g a g e n t ’s e x p l a n a t i o n s w h i l e f i x i n g u p t h e p r o b l e m h i m o r h e r s e l f .
-
Page 9: Trouble Shooting
9 . TROUBLE SHOOTING PROBLEM POSSIBLE CAUSE REMEDY Film Surface Not Smooth Film and container incompatible Be sure you are using the same film material as the material of the container Residue on the mold Use a damp cloth or plastic brush to clean the mold Sealing time too short Increase sealing time Temperature too low or high... - Page 10 Upper Mold Does Not Descend Faulty micro switch or wire connection Repair or replace as needed to micro switch Base Mold Does Not Eject Faulty micro switch or wire Repair or replace as needed connection to micro switch Bearing off track Turn off machine &...
- Page 11 10 ELECTRICAL DLAGRAM Power light Timer 1 Thermostat 1 Heating 1 Heating 1 Timer 2 Thermostat 2 Heating2 Heating 2 Rolling motor Seal valve In/Out motor Seal lift valve Gas valve 9 ...
- Page 12 10 ELECTRICAL DLAGRAM Sensor Counter Seal time Auto/manual Start Safe door stop Limit switch(In) Limit switch(Out) Seal top limit switch Seal down limit switch Add length Reduce length Manual start Sensor Roll motor Seal down valve In motor Out Motor Power Seal lift Gas inlet Seal time...
Need help?
Do you have a question about the VT-109 and is the answer not in the manual?
Questions and answers