KVANT Architect Series Operational Manual
Hide thumbs
Also See for Architect Series:
- Operation manual (33 pages) ,
- Operational manual (28 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for KVANT Architect Series
Summary of Contents for KVANT Architect Series
- Page 1 MODEL SPECIFIC OPERATIONAL MANUAL architect series Last updated: 28.08.2024...
-
Page 2: Table Of Contents
table of contents 1. Introduction 2. General information 2.1 What is a laser and how does it work? 2.2 Laser Safety first! 2.3 Installation ofthe System 2.4 Control System 2.5 Control Options 2.6 Connection Diagram 2.7 Multiple System Interlock 2.8 Switching ON sequence and User Interlock 2.9 Maintenance 3. -
Page 3: Introduction
Thank you for purchasing this KVANT product. To ensure proper operation, please read this manual carefully before using the product. After reading it, keep it in a safe place for future reference. -
Page 4: General Information
__ W MAX OUTPUT AT __ nm DANGER ___W AT ________nm IEC 60825 - 1:2014 KVANT This product is in conformity with performance standards for laser products under 21 CFR Part 1010.4 and 1040.11 except with respect to those characteristics authorized by... -
Page 5: Handling Precautions
The manufacturer and its distributors cannot be held responsible for any Transportation handles damages caused by improper use or misuse of this KVANT laser system. The owner/user is fully responsible for During the handling, transportation and installation using this product in accordance to laser procedure use only dedicated foldable transportation safety regulations of the country or state... -
Page 6: What Is A Laser And How Does It Work
what is a laser and how does it work? What is a LASER? The laser is a device that creates continuous visible light energy waves (streams of photons that are referred to as “laser radiation”) with the same amplitude and phase that are flowing in the same direction; meaning they are coherent – they stick together and form a laser beam. -
Page 7: Laser Safety First
laser safety first! Any laser system classified as a Class Before proceeding any further, please 4 laser must be used with caution. read the following safety page very If you are an inexperienced laser carefully. It could help you avoid operator, we strongly recommend dangerous and hazardous situations that you attend a ... -
Page 8: Installation Ofthe System
installation of the system In case of water cooled version, do not use the laser system without the cooling fluid. Make that the laser The manufacturer is not liable for damages system is properly connected to the chiller device or a injury caused by improper installation using the supplied hoses, and that the fluid level is of ... -
Page 9: Control System
Please make sure all the laser settings in your control dependent on the control system that you use for operating system are set correctly before you start using your Kvant the laser as well as the correct device configuration in the laser display system. -
Page 10: Control Options
Analog control option = Architect remote control Kvant Architect laser system with analog control option is dedicated to display static beams with locally adjustable brightness for each R, G, or B colour. Architect Remote Controller with adjusters for each color is supplied with each fixture. -
Page 11: Connection Diagram
CONTROL DEVICE ARCHITECT Shutter REMOTE Analog control option (Architect remote control), CONTROL DMX lighting desk LASER Control signal cable (to DMX) EMISSION WARNING LIGHT Safety key KVANT ARCHITECT LIGHTING SYSTEM E STOP Power input Remote Safety remote 2-pin SF12 REMOTE... -
Page 12: Multiple System Interlock
E-STOP Remote to each plugged Architect laser system and they are fully compatible with all Kvant laser systems using E-STOP Remote standard. The E-STOP splitter has two inputs, thus two E-STOP Remotes can be used and you can control the Architect laser systems... -
Page 13: Switching On Sequence And User Interlock
3. Safety key Switch on E-STOP Remote turned to OFF position. 4. Shutter switch turned to OFF position or DMX channel 4 changed to 0 value. 5. E-STOP Remote disconnected from KVANT Architect laser system. DMX control Analog controller DMX lighting desk Architect remote conrol 6. -
Page 14: E-Stop Connection Drawing Including User Interlock Option
"User E-Stop Connector" on "Kvant E-Stop Remote". (XLR Female) If "User E-Stop switch" is connected to "Kvant E-Stop Remote" and is in OPEN state, all "Kvant Laser projetors" connected to "Kvant E-Stop Remote" are disabled. In this case NO EMISSION is possible. -
Page 15: Maintenance
It is essential to regularly inspect the of the KVANT laser system. You should perform a visual condition of the silica gel granules check of output window cleanliness and clean up every inside the cartridges. - Page 16 Disposal of the equipment The equipment is made of components and materials such as metal, plastic, aluminium, which can be dismantled, sorted and recycled in accordance with the Waste Act at the end of the life of the equipment or when it is no longer functional.
-
Page 17: Item Checklist
Item Number of units Descriptions Item Number of units Descriptions 1x Architect Remote Control KVANT Architect Laser System 1x 1x Emergency STOP remote and Remote Controller User manual USB drive US version BUS ID: 1647 BUS ID: 1054 EU version BUS ID: 1648 1x ... -
Page 18: System Overview
KVANT Architect is a full colour, semiconductor diode The system is fluid cooled and designed with no airflow laser system designed for professional laser illumination going through the optical compartment of the system. purposes and static visual beam effects. -
Page 19: Top View
top view 690,6 453,6 1. Laser aperture. 2. Laser emission warning light. When this indicator is lit up the laser system can emit the laser radiation. 3. 8pcs top cover fast access fasteners. 4. 4pcs transportation handles. To access the optical compartment of the laser system pull up the fasteners and release the clamps from hooks and carefully remove the top cover. -
Page 20: Back View
4. Chiller hose connectors. 3. Input signal cable. Kvant Architect systems use either analog input levels 0-5V It is necessary to plug chiller hoses in the connectors for or DMX siglnal to control the output power. This is model succesfull cooling of the laser projector system. -
Page 21: Beam Alignment
beam alignment It is possible that due to transportation, rigging, moving This Architect laser system is rated around or vibrations caused by various elements during as a Class IV laser product and a set up or laser performance some of the internal optical manufactured in ... -
Page 22: Technical Specifications
technical specifications All the technical specifications are subject to change without prior notice. -
Page 23: Technical Specifications [Architect W400B]
technical specifications [architect w Low divergent, high power, full colour, full diode, static architectural laser source Total optical power 458 W consist of: 114W red, 188W green, 156W blue Total luminous flux: 122 750 lm Water cooled version. General specifications Green Blue White...
Need help?
Do you have a question about the Architect Series and is the answer not in the manual?
Questions and answers