Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for KVANT SPECTRUM Series
Summary of Contents for KVANT SPECTRUM Series
- Page 1 MODEL SPECIFIC OPERATIONAL MANUAL spectrum series...
-
Page 2: Table Of Contents
table of contents 1. Introduction 2. General information 2.1 What is a laser and how does it work? 2.2 Laser Safety first! 2.3 Installation ofthe System 2.4 Control System 2.5 Scanning System 2.6 Connection Diagram 2.7 Multiple System Interlock 2.8 Switching ON sequence and User Interlock 2.9 Maintenance 3. -
Page 3: Introduction
Thank you for purchasing this KVANT product. To ensure proper operation, please read this manual carefully before using the product. After reading it, keep it in a safe place for future reference. -
Page 4: General Information
LASER LIGHT IS BRIGHT AND BLINDING DO NOT SHINE AT IEC 60825 - 1:2014 AIRCRAFT OR VEHICLES AT ANY DISTANCE KVANT This product is in conformity with performance standards for laser products under 21 CFR CAUTION Part 1010.4 and 1040.11 except with respect... - Page 5 The manufacturer and its distributors cannot be held responsible for any damages caused by improper use or misuse of this KVANT laser system. Please note that some other optical devices such The owner/user is fully responsible for as cameras, camcorders, video projector etc. can using this product in accordance to laser...
-
Page 6: What Is A Laser And How Does It Work
what is a laser and how does it work? What is a LASER? The laser is a device that creates continuous visible light energy waves (streams of photons that are referred to as “laser radiation”) with the same amplitude and phase that are flowing in the same direction; meaning they are coherent – they stick together and form a laser beam. -
Page 7: Laser Safety First
laser safety first! Any laser system classified as a Class Before proceeding any further, please 4 laser must be used with caution. read the following safety page very If you are an inexperienced laser carefully. It could help you avoid operator, we strongly recommend dangerous and hazardous situations that you attend a ... -
Page 8: Installation Ofthe System
installation of the system Please follow these rules during the installation: The manufacturer is not liable for damages or a injury caused by improper installation of the system. The installation should Do not connect the device to power supply during be carried by a qualified installer who the installation. -
Page 9: Control System
Please make sure all the laser settings in your control dependent on the control system that you use for operating system are set correctly before you start using your Kvant the laser as well as the correct device configuration in the laser display system. -
Page 10: Scanning System
scanning system How to establish correct Scan-rate and maximal The product warranty does not cover the damages to the scanning system caused by improper use of the number of points in an effect scanning system or by incorrect programming. Therefore Each effect (picture) contains a different number of graphical it is essential to understand how the scanning works and points which defines the actual shape of ... - Page 11 In the following pictures you see the same star effect scanned at different scan rates at full scanning angle (60 degrees). Picture 1: the scan rate and/or number Picture scan-rate and/ Picture 3: further increasing of the of points is too low. The corner or number of points is about right. scan-rate and/or ...
-
Page 12: Connection Diagram
connection diagram Please check that all the signal and power leads are correctly installed and that the safety keys are inserted in all necessary positions. Both E-STOP Remote safety key and i laser system safety key must be inserted and switched to ON position in order to disable the interlock. -
Page 13: Multiple System Interlock
multiple system interlock Multiple laser projectors may be daisy chained and controlled by a single E-STOP Remote. Any event which enables the Interlock on any laser projector in the daisy chain will trigger the safety Interlock for all the systems. After the event has been corrected the START button on the E-STOP Remote must be pressed by the operator to disable the Interlock. -
Page 14: Switching On Sequence And User Interlock
KVANT laser system is being used before switching the system ON. Power loss lasting greater than 2 seconds. 2. Mushroom emergency switch depressed. - Page 15 E-STOP Connection Drawing including User Interlock option The E-STOP Remote is an integral part of the laser projector. It is there for the safety of the public as well as the operator. Modifying or using anything other than E-STOP Remote provided, in the manner it was intended, may invalidate your laser projector’s variance.
-
Page 16: Maintenance
maintenance Maintenance: no user serviceable parts inside. Aperture Window Drying agent cartridge To clean the aperture output window use a soft cloth Drying agent cartridge (silica gel desiccant) helps to prevent and medical grade isopropyl alcohol. If necessary, you water condensation inside the optical compartment of the can remove the aperture output window by ... -
Page 17: Item Checklist
Before starting, check that all the following items have been included with your laser system. If anything is missing, contact your supplier. Number of units Descriptions Number of units Descriptions Item Item 2x KVANT Spectrum Laser Display Set of Safety Keys System 1x Emergency STOP remote User manual USB drive US version BUS ID: 1647 BUS ID: 1054... -
Page 18: Optional Accessories
optional accessories Here is a list of optional accessories that are compatible with Spectrum laser system. Descriptions Item SafetyScan lens attachment bracket (lens is not included). DiscoScan lens attachment bracket (lens is not included). 4-way masking plate Rain cover... -
Page 19: System Overview
KVANT Spectrum is a full colour, OPSL & semiconductor The system is air-cooled and designed so that there diode laser system designed for professional laser displays. is no airflow going through the optical compartment of the system. This ensures that all important optical parts of the When operated correctly and in ... -
Page 20: Front View
front view 1. Laser aperture. 2. Aperture masking plate. To clean the laser aperture window from inside or to swap the This metal masking plate can be moved left and right when aperture plate for different type of aperture (i.e. DiscoScan locking bolt is loosened. lens attachment bracket), remove the six socket bolts that hold the laser aperture in place and remove it. -
Page 21: Rear View
rear view 1. Mains power INPUT/OUTPUT. Use supplied Neutrik 2. E-STOP Remote connector, Interlock status indicator powerCON TRUE1 power cable to connect the laser system and User Interlock. In order to use the laser system, the to mains power supply using the INPUT connector. The Interlock must be closed circuit. - Page 22 The projector’s REMOTE Output is used to daisy-chain the After a power failure or interlock failure (open circuit) Remote signal when you want to use a single Emergency has occurred and been corrected you need to manually STOP Remote to control multiple systems. reset laser emission by pressing the START button on the E-STOP Remote.
-
Page 23: Beam Alignment
beam alignment Beam alignment principle It is possible that due to transportation, rigging, moving around or vibrations caused by various elements during There are three laser modules within this system where a set up or laser performance some of the internal optical each module produces one of the basic RGB colours (red, parts can move slightly resulting in colour misalignment. -
Page 24: Beam Alignment [Spectrum 30 Rogb]
[spectrum rogb] 4. Power up the system as normal. Although KVANT uses the latest 5. Firstly, it is necessary to align a colour with the most technology to protect all the critical components inside this laser system direct beam path between the laser module output against Electrostatic Discharge, the and the scanning system in ... - Page 25 Create a cyan beam effect (point) and check visually 9. Create a full size magenta circle (static tunnel effect) whether the green beam hits the exact centre of the and check whether the red circle overlays the blue blue beam at the dichroic filter DF4. If not, use dichroic circle in all points around the shape.
-
Page 26: Beam Alignment [Spectrum 33 Rygb]
[spectrum rygb] 4. Power up the system as normal. Although KVANT uses the latest 5. Firstly, it is necessary to align a colour with the most technology to protect all the critical components inside this laser system direct beam path between the laser module output against Electrostatic Discharge, the and the scanning system in ... - Page 27 9. Create a full size magenta circle (static tunnel effect) and check whether the red circle overlays the blue circle in all points around the shape. If not, use dichroic mount DF1 to adjust the beam path accordingly. To adjust the dichroic mount use the two adjustment knobs –...
-
Page 28: Beam Alignment [Spectrum 45 Rygb]
[spectrum rygb] 4. Power up the system as normal. Although KVANT uses the latest 5. Firstly, it is necessary to align a colour with the most technology to protect all the critical components inside this laser system direct beam path between the laser module output against Electrostatic Discharge, the and the scanning system in ... - Page 29 Create a cyan beam effect (point) and check visually 9. Create a full size magenta circle (static tunnel effect) whether the green beam hits the exact centre of the and check whether the red circle overlays the blue blue beam at the dichroic filter DF4. If not, use dichroic circle in all points around the shape.
-
Page 30: Beam Alignment With Motorised Dichroid Filters
B: Create a full-size white circle (static tunnel effect). B: Go to : PROJECTOR SETTINGS -> KVANT DICHRO tab. There you will find all the information and control C: Find Beam Alignment options for the dichroic option in the menu and enter filters. -
Page 31: Technical Specifications
technical specifications All the technical specifications are subject to change without prior notice. -
Page 32: Technical Specification [Spectrum 30 Rogb]
[spectrum rogb] Module Power KVANT Spectrum 30 ROGB – full colour, OPSL & semiconductor diode laser system Colour Type Wavelenght installed Total Optical Power (installed): 30W RLM-6000L2 637nm 6000mW Total Optical Power (guaranteed): 30W* Orange OPSL 590nm *Due to Advanced Optical Correction technology used 3000mW in ... -
Page 33: Technical Specification [Spectrum 33 Rygb]
[spectrum rygb] KVANT Spectrum 33 RYGB – full colour, OPSL & Module Power semiconductor diode laser system Colour Type Wavelenght installed Total Optical Power (installed): 33W RLM-7000L 637nm 7000mW Total Optical Power (guaranteed): 33W* Yellow OPSL 577nm 5000mW *Due to ... -
Page 34: Technical Specification [Spectrum 45 Rygb]
[spectrum rygb] Module Power KVANT Spectrum 45 RYGB – full colour, OPSL & semiconductor diode laser system Colour Type Wavelenght installed Total Optical Power (installed): 45W RLM-9kF 637nm 9000mW Total Optical Power (guaranteed): 45W* Yellow OPSL 577nm *Due to Advanced Optical Correction technology used 5000mW in ... -
Page 35: Troubleshooting
Can I continue using my projector? operation? A: Laser beams hitting glass splits will be scattered into A: Yes, it’s OK. Kvant projectors have built-in automatic unwanted directions, creating a risk of damage to eyesight, regulation of the fan speed. After powering up the health or property. - Page 36 (or disconnect the mains ILDA input. Please contact your distributor or technical power cord) for 10 minutes. assistance of Kvant Lasers, s.r.o. for further help. All PSUs should fully discharge and cool down. After 10 minutes, power up the projector. If overloaded Q: Projection is ...
- Page 37 Q: The projection suddenly lost a significant amount Q: Is this projector compatible with other Kvant projectors? of blue colour. The colour tone of all RGB effects changed, A: All Kvant projectors manufactured from 06/2014 and and the total power output decreased too. Why? later are fully compatible with each other.
- Page 38 Rain Cover installed. at high ambient temperatures. What shall I do next? A: The operating temperature range for Kvant laser A: It is necessary to remove the laser projector from its projectors is +10°C (50°F) to +35°C (95°F). Using projectors flight case as soon as possible - within 24 hours at the in an environment with air temperatures within 35°C (95°F)
- Page 39 Q: Can anybody operate the laser projector? Q: How can I ecologically discard an old laser projector? A: No. The laser projector should be operated A: Laser projector doesn’t contain any poisonous materials by an adult person passed their training or dangerous components. Therefore, you can ecologically as ...
-
Page 40: Contact Information
Software: PANGOLIN Address: Address: Kvant Lasers s.r.o. Pangolin Laser Systems, Inc. Odborárska 23 1265 Upsala Road, suite 1165 831 02 Bratislava Sanford, FL 32771 Slovakia, Europe Technical support contact: e-mail: info@kvant.sk e-mail: support@pangolin.com Telephone: 00421-2-654 113 55 Telephone: +(407) 299-2088 Technical support contact: e-mail: micek@kvant.sk ... -
Page 41: Dimension Details
BOTTOM VIEW dimension details REAR VIEW SIDE VIEW FRONT VIEW handle fully rotatable 360 degrees TOP VIEW BOTTOM VIEW Purple: Overall dimensions, including all the fittings and extrusions; without the 360º swivel bracket Total airflow needed for the laser projector: 232 cubic metres per hour FRONT VIEW TOP VIEW...
Need help?
Do you have a question about the SPECTRUM Series and is the answer not in the manual?
Questions and answers