Inel PIL-19DLT Instructions

Operating instructions for
The remote control is made in two versions:
•
PIL-19DLT - 19-channel remote control
•
PIL-99DLT - 99-channel remote control
The remote control is equipped
with five keys on the front panel:
Key "up"
Key "stop"
Key "down"
Key "plus"
Key "minus"
The remote control has
2 keys under the flap with a battery:
✓ Clock" key
✓ M key "menu"
Registering remote controls
Control of any channel from the PIL-19/99DLT remote control is
possible
after this channel has been registered to the respective drive or
driver.
In our devices, we distinguish between the following ways of
entering the programming option:
1. First programming after switching on the supply voltage (radio
drive, ST-01RL),
2. First programming of the ST-01R controller,
3. Programming using a previously programmed remote control
(radio drive, ST-01RL, ST-01R).
Initial programming for radio drives and
ST-01RL controllers:
- connect a 230 VAC power supply to the drive/controller,
- within 10 seconds of the power being switched on, briefly press
simultaneously the ▲ "up" and ▼ "down" keys of the remote
control (the display shall briefly show the sign ),
- the engine will make an up and down movement,
- within the next 10
▲ "up" on the selected remote control channel,
- a short up and down movement will confirm that the registration is
correct.
ATTENTION The procedure will erase from the drive's memory
all pilots that were previously registered.
First programming of the ST-01R controller:
- press programming button S1 - the LED will flash and remain on
continuously,
- then briefly press the ▲ "up" key of the remote control, - the
controller shall signal the registration of the remote control by
blinking green and red LEDs,
Once you have a registered remote control
Register further remote controls without switching off the power
supply. Using the previously registered remote control, enter the
drive/controller into programming mode.
- briefly press simultaneously ▲ "up" and ▼ "down" of the
registered remote control channel,
- the motor makes an up and down movement, followed by a series
of short up and down movements equal to the number of registered
remote controls and the LED on the control unit lights up green
- within the next 10 seconds, briefly press the ▲ "up" key of the new
channel or the new remote control
Instructions translated EN
Models:
PIL-19DLT, PIL-99DLT
seconds briefly press the
type remote controls
PIL
- the motor makes a series of short up and down movements
confirming the registration of the next channel and the LED on the
controller goes out.
Remote control menu
To enter the remote control menu, press the M key
located under the battery flap.
Use the ▲ "up" and ▼ "down" keys to navigate
through the menu. The
selected option. To go back to the main menu, press
the "stop" key again.
The menu consists of the following options:
- Programmes Setting of time programmes
- Names Naming channel numbers
- Clock Date and time settings
- Partial setting the shutter release
(made in time programmes)
- Sun Setting the sundial
- Other language and display brightness settings
The menu is exited by pressing the M key again.
Programmes
In the Programmes option, you set and change
programmes for automatic opening, closing,
unsealing and stopping (applies to control of e.g.
lighting) of specific roller shutters or groups of roller
shutters at a specific time and on a specific day of the
week. There are 32 programmes available,
numbered 00 to 31. The programmes can be set as
"Active" or "Inactive". The days of the week on
which the programme is to run are set by specifying
"day from "and "day to" inclusive.
For example, "Mon - Mon" means Monday only,
"Sat - Sun" means Saturday and Sunday, and "Mon - Sun" means all
days of the week. The time at which the programme is to run is specified
by specifying hour and minutes or sun (east) and moon (west). Minutes
can only be specified as multiples of 5. To fully define the programme,
you still need to specify the channel number from 00 to 19 (PIL-19DLT)
or up to 99 (PIL-99DLT) and the action to be performed: opening
("Otw."), closing ("Zam."), unsealing ("Roz") or stopping ("Stop"). The
setting shall be performed with the use of "▲" and "▼" keys. The value
indicated by the cursor (underline) shall be changed. The cursor
position is changed with the "-" and "+" keys. Pressing the "stop" key
moves the cursor to the program number. Changing the programme
number saves the changes made to the existing programme. After the
key
completion of the programmed task, the information with the number
of the last executed programme remains on the display (main screen).
NOTE
The times of the set programmes cannot be identical (the time of
opening/closing two or more roller shutters cannot be the same). If
you want to set the same time for several roller shutters, you must
create a group of roller shutters (by registering one remote
control channel for several roller shutters).
NOTE
Timed programmes are only executed when the clock icon is
displayed in the top right corner. To activate the timer
programmes, briefly press the key with the clock icon (under the
battery flap).
Names
In the "Names" option, text (capital letters and
numbers) can be assigned to each channel number,
up to a maximum of 16 characters in two lines of 8
characters each. The underline (cursor) indicates the
position, which can be changed with the "▲" and
"▼" keys. The "-" and "+" keys change the position
of the cursor. The name is saved after changing the channel number or
stop" key enters the