Ignition 2bright pint TW200 IP MK II User Manual

Led par

Advertisement

Quick Links

2bright pint TW200 IP MK II
LED PAR

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 2bright pint TW200 IP MK II and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Ignition 2bright pint TW200 IP MK II

  • Page 1 2bright pint TW200 IP MK II LED PAR...
  • Page 2 Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 Internet: www.thomann.de 29.01.2025, ID: 556156 (V2)
  • Page 3: Table Of Contents

    7.6 Functions in 2-channel DMX mode, variant B............... 41 7.7 Functions in 3-channel DMX mode................... 44 7.8 Functions in 4-channel DMX mode................... 48 7.9 Functions in 5-channel DMX mode................... 49 7.10 Functions in 8-channel DMX mode..................55 Technical specifications........................63 2bright pint TW200 IP MK II LED PAR...
  • Page 4 Table of contents Plug and connection assignments....................66 Troubleshooting............................67 Cleaning............................... 69 Protecting the environment......................70 2bright pint TW200 IP MK II LED PAR...
  • Page 5 2bright pint TW200 IP MK II LED PAR...
  • Page 6: General Information

    1.1 Symbols and signal words In this section you will find an overview of the meaning of symbols and signal words that are used in this document. 2bright pint TW200 IP MK II LED PAR...
  • Page 7 Warning signs Type of danger Warning – high-voltage. Warning – hot surface. Warning – dangerous optical radiation. 2bright pint TW200 IP MK II LED PAR...
  • Page 8 General information Warning signs Type of danger Warning – suspended load. Warning – danger zone. 2bright pint TW200 IP MK II LED PAR...
  • Page 9: Safety Instructions

    Always dispose of packaging material properly when it is not in use. Never allow children to use the device without supervi‐ sion. Keep small parts away from children and make sure that the device does not shed any small parts (such knobs) that children could play with. 2bright pint TW200 IP MK II LED PAR...
  • Page 10 The surface of the device becomes very hot during operation. Skin contact can result in burns. Never touch the device with your bare hands during operation. After switching off the device, wait for at least 15 minutes before touching it. 2bright pint TW200 IP MK II LED PAR...
  • Page 11 “Technical specifications” chapter of the user manual is not exceeded. Only use power cords with a cable cross-section designed for the required current intensity when connecting the devices in series. 2bright pint TW200 IP MK II LED PAR...
  • Page 12: Features

    For technological reasons, the light output of LEDs decreases over their lifetime. This effect increases with higher operating temperature. You can extend the service life of the illuminants by providing adequate ventilation and operating the LEDs with the lowest possible brightness. 2bright pint TW200 IP MK II LED PAR...
  • Page 13: Installation

    Always secure the barn door with a safety cable on the spotlight. The safety cable must run outside the barn door to not interfere with the light emission. 2bright pint TW200 IP MK II LED PAR...
  • Page 14 If the device is mounted on an unsuitable stand, there is a risk that the stand will fall over and cause damage. Only use stands whose maximum bearing capacity is at least as high as the weight of the device. Always ensure that the stand is stable. 2bright pint TW200 IP MK II LED PAR...
  • Page 15 (first code number). They are also protected against splash water from any angle (second code digit). That is why this equipment can also be used outdoors. Event technology equipment is generally only designed for temporary use however (event lighting) and not for permanent use outdoors. 2bright pint TW200 IP MK II LED PAR...
  • Page 16: Mounting Options

    Additionally secure the device with a safety cable against falling. The safety cable must be attached to the bracket. Please note that this device must not be connected to a dimmer. 2bright pint TW200 IP MK II LED PAR...
  • Page 17 Installation Comply with regulations When installing and operating, make sure to follow the standards and regulations that apply in your country. 2bright pint TW200 IP MK II LED PAR...
  • Page 18: Starting Up

    Connect the output of the first DMX device to the input of the second one, and so on to form a daisy chain. Always ensure that the output of the last DMX device in the daisy chain is terminated with a resistor (110 Ω, ¼ W). 2bright pint TW200 IP MK II LED PAR...
  • Page 19: Connections And Controls

    Connections and controls Connections and controls ö ö & 2bright pint TW200 IP MK II LED PAR...
  • Page 20 6 [POWER OUT] | Lockable panel socket (Power Twist TR1 IP65) for the power supply for another device 7 Bracket for suspension or set-up 8 [POWER IN] | Lockable panel socket (Power Twist TR1 IP65) for the power supply of the device 2bright pint TW200 IP MK II LED PAR...
  • Page 21: Operating

    Press [ENTER] to select the required menu item or adopt the displayed value. To exit a menu item without making changes, press [MENU]. ð The set values are retained even when you switch the device off and disconnect it from the mains. 2bright pint TW200 IP MK II LED PAR...
  • Page 22 DMX address for the various DMX modes. Mode Display Highest possible DMX address 1-channel ‘1CH’ 2-channel, variant A ‘2CH A’ 2-channel, variant B ‘2CH B’ 3-channel ‘3CH’ 4-channel ‘4CH’ 5-channel ‘5CH’ 8-channel ‘8CH’ 2bright pint TW200 IP MK II LED PAR...
  • Page 23 Depending on the selected mode, the display shows ‘1CH’ , ‘2CH A’ , ‘2CH B’ , ‘3CH’ , ‘4CH’ , ‘5CH’ or ‘8CH’ . Press [ENTER] to accept the selection. This setting is only relevant when the device is controlled via DMX. 2bright pint TW200 IP MK II LED PAR...
  • Page 24 Adjust the brightness of the warm white ‘ColdWhite’ ‘0…255’ Adjust the brightness of the cold white ‘Dimmer’ ‘0…255’ Adjusting the dimmer intensity (0% to 100%) ‘Strobe’ ‘0…30Hz’ Adjusting the strobe effect frequency between 0 Hz and 30 Hz 2bright pint TW200 IP MK II LED PAR...
  • Page 25 Press [UP] or [DOWN] repeatedly until the display shows ‘Display Reverse’ . Confirm with [ENTER]. Use [UP] or [DOWN] to select either ‘On’ (display rotated by 180°) or ‘Off’ (display not rotated). Press [ENTER] to accept the selection. 2bright pint TW200 IP MK II LED PAR...
  • Page 26 Press [UP] or [DOWN] repeatedly until the display shows ‘Display Backlight’ . Confirm with [ENTER]. Use [UP] or [DOWN] to select either ‘On’ (display permanently on) or ‘Off’ (display turns off after a few seconds of inactivity). Press [ENTER] to accept the selection. 2bright pint TW200 IP MK II LED PAR...
  • Page 27 ‘Hold’ The last received signal is held. ‘Blackout’ The spotlight is turned off. ‘ManualMode’ The device calls up the values set in the ‘Stand Alone’ menu. Press [ENTER] to accept the selection. 2bright pint TW200 IP MK II LED PAR...
  • Page 28 Fade time 1 s: Rise time 2,040 ms, fall time 2,120 ms ‘Theatre’ Without fade time: Rise time 1,580 ms, fall time 1,940 ms Fade time 1 s: Rise time 2,230 ms, fall time 2,280 ms 2bright pint TW200 IP MK II LED PAR...
  • Page 29 Press [UP] or [DOWN] repeatedly until the display shows ‘Dimmer Speed’ . Confirm with [ENTER]. Use [UP] or [DOWN] to select a dimmer speed between ‘0.1-0.9s’ (0.1 seconds to 0.9 sec‐ onds) and ‘1-10s’ (1 second to 10 seconds). Press [ENTER] to accept the selection. 2bright pint TW200 IP MK II LED PAR...
  • Page 30 Use [UP] or [DOWN] to select either ‘On’ (keylock on) and ‘Off’ (keylock off). Press [ENTER] to accept the selection. To release the key lock, press and hold [UP] and [DOWN] simultaneously for 5 seconds. 2bright pint TW200 IP MK II LED PAR...
  • Page 31 The fan is off (silent mode). The device temperature is controlled by reducing the power consumption to a maximum of 70 W. ‘Max’ The fan runs at maximum speed. Press [ENTER] to accept the selection. 2bright pint TW200 IP MK II LED PAR...
  • Page 32 ‘1100Hz’ PWM 1.1 kHz ‘1200Hz’ PWM 1.2 kHz ‘1300Hz’ PWM 1.3 kHz ‘1400Hz’ PWM 1.4 kHz ‘1500Hz’ PWM 1.5 kHz ‘2500Hz’ PWM 2.5 kHz ‘4000Hz’ PWM 4 kHz ‘5000Hz’ PWM 5 kHz 2bright pint TW200 IP MK II LED PAR...
  • Page 33 Press [UP] or [DOWN] repeatedly until the display shows ‘Reset’ . Confirm with [ENTER]. ð You are prompted to enter a password. Enter the password 11. Press [ENTER]. ð The device is reset to factory default settings. 2bright pint TW200 IP MK II LED PAR...
  • Page 34 Use [UP] or [DOWN] to select the value for the calibration of the colour temperature. The following table shows the available options. Menu level 4 Menu level 5 Function ‘Warm’ ‘000…255’ Calibrating warm white ‘Cold’ ‘000…255’ Calibrating cold white Press [ENTER] to accept the selection. 2bright pint TW200 IP MK II LED PAR...
  • Page 35 Press [MENU] and then [UP] or [DOWN] repeatedly until the display shows ‘System Info’ . Confirm with [ENTER]. Press [UP] or [DOWN] until the display shows ‘Total Operation Hours’ . ð The operation hours of the device are displayed. 2bright pint TW200 IP MK II LED PAR...
  • Page 36 Confirm with [ENTER]. Press [UP] or [DOWN] until the display shows ‘RDM’ . ð The UID code is displayed. Parameter ID Detection com‐ Sent command Received mand command DISC_UNIQUE_BRANCH DISC_MUTE DISC_UN_MUTE DEVICE_INFO 2bright pint TW200 IP MK II LED PAR...
  • Page 37 Operating Parameter ID Detection com‐ Sent command Received mand command SOFTWARE_VERSION_LABEL DMX_START_ADDRESS IDENTIFY_DEVICE SUPPORTED_PARAMETERS SENSOR_DEFINITION SENSOR_VALUE DMX_PERSONALITY DMX_PERSONALITY_DESCRIPTION RESET_DEVICE FACTORY_DEFAULTS 2bright pint TW200 IP MK II LED PAR...
  • Page 38: Menu Overview

    Operating 7.3 Menu overview DMX Address DMX Mode Stand Alone 001...512 2CH A 2700...7000K 2CH B WarmWhite 0...255 ColdWhite 0...255 Dimmer 0...255 Strobe 0...30Hz AutoFade No fade 0.5s...30s 2bright pint TW200 IP MK II LED PAR...
  • Page 39 Dimmer Curve 1400Hz Linear 1500Hz Stage 2500Hz 4000Hz Architectural 5000Hz Theatre 6000Hz Stage2 10000Hz Dimmer Speed 0.1-0.9s...1-10s Service AutoLock On/Off Reset Passcode=11 Fan Mode Calibration Smart Passcode=50 Silent Warm 000...255 Cold 000...255 2bright pint TW200 IP MK II LED PAR...
  • Page 40: Functions In 1-Channel Dmx Mode

    Function 000…255 Blinder mode (0% to 100%) 7.5 Functions in 2-channel DMX mode, variant A Channel Value Function 000…255 Cold white intensity (0% to 100%) 000…255 Warm white intensity (0% to 100%) 2bright pint TW200 IP MK II LED PAR...
  • Page 41: Functions In 2-Channel Dmx Mode, Variant B

    2,800 K 041…045 2,900 K 046…050 3,000 K 051…055 3,100 K 056…060 3,200 K 061…065 3,300 K 066…070 3,400 K 071…075 3,500 K 076…080 3,600 K 081…085 3,700 K 086…090 3,800 K 2bright pint TW200 IP MK II LED PAR...
  • Page 42 4,400 K 121…125 4,500 K 126…130 4,600 K 131…135 4,700 K 136…140 4,800 K 141…145 4,900 K 146…150 5,000 K 151…160 5,100 K 161…165 5,200 K 166…170 5,300 K 171…175 5,400 K 2bright pint TW200 IP MK II LED PAR...
  • Page 43 5,800 K 196…200 5,900 K 201…205 6,000 K 206…210 6,100 K 211…215 6,200 K 216…220 6,300 K 221…225 6,400 K 226…230 6,500 K 230…235 6,600 K 236…240 6,700 K 241…245 6,800 K 2bright pint TW200 IP MK II LED PAR...
  • Page 44: Functions In 3-Channel Dmx Mode

    Intensity of the master dimmer from dark (0) to light (255) Colour temperature from 2.700 K to 7.000 K 000…035 2,700 K 036…040 2,800 K 041…045 2,900 K 046…050 3,000 K 051…055 3,100 K 056…060 3,200 K 061…065 3,300 K 2bright pint TW200 IP MK II LED PAR...
  • Page 45 3,900 K 096…100 4,000 K 101…105 4,100 K 106…110 4,200 K 111…115 4,300 K 116…120 4,400 K 121…125 4,500 K 126…130 4,600 K 131…135 4,700 K 136…140 4,800 K 141…145 4,900 K 2bright pint TW200 IP MK II LED PAR...
  • Page 46 5,500 K 181…185 5,600 K 186…190 5,700 K 191…195 5,800 K 196…200 5,900 K 201…205 6,000 K 206…210 6,100 K 211…215 6,200 K 216…220 6,300 K 221…225 6,400 K 226…230 6,500 K 2bright pint TW200 IP MK II LED PAR...
  • Page 47 011…020 LED on 021…030 Single strobe pulse 031…090 Strobe effect, increasing speed 091…100 LED on 101…170 Strobe pulses, increasing speed 171…180 LED on 181…240 Random strobe effect, increasing speed 241…255 LED on 2bright pint TW200 IP MK II LED PAR...
  • Page 48: Functions In 4-Channel Dmx Mode

    011…020 LED on 021…030 Single strobe pulse 031…090 Strobe effect, increasing speed 091…100 LED on 101…170 Strobe pulses, increasing speed 171…180 LED on 181…240 Random strobe effect, increasing speed 241…255 LED on 2bright pint TW200 IP MK II LED PAR...
  • Page 49: Functions In 5-Channel Dmx Mode

    2,800 K 041…045 2,900 K 046…050 3,000 K 051…055 3,100 K 056…060 3,200 K 061…065 3,300 K 066…070 3,400 K 071…075 3,500 K 076…080 3,600 K 081…085 3,700 K 086…090 3,800 K 2bright pint TW200 IP MK II LED PAR...
  • Page 50 4,400 K 121…125 4,500 K 126…130 4,600 K 131…135 4,700 K 136…140 4,800 K 141…145 4,900 K 146…150 5,000 K 151…160 5,100 K 161…165 5,200 K 166…170 5,300 K 171…175 5,400 K 2bright pint TW200 IP MK II LED PAR...
  • Page 51 6,000 K 206…210 6,100 K 211…215 6,200 K 216…220 6,300 K 221…225 6,400 K 226…230 6,500 K 230…235 6,600 K 236…240 6,700 K 241…245 6,800 K 246…250 6,900 K 251…255 7,000 K 2bright pint TW200 IP MK II LED PAR...
  • Page 52 Random strobe effect, increasing speed 241…255 LED on Dimmer curves 000…010 Default setting of the device 011…020 Dimmer curve ‘Linear’ 021…040 Dimmer curve ‘Stage’ 041…060 Dimmer curve ‘TV’ 061…080 Dimmer curve ‘Architectural’ 2bright pint TW200 IP MK II LED PAR...
  • Page 53 Delay 0.3 s Delay 0.4 s Delay 0.5 s Delay 0.6 s Delay 0.7 s Delay 0.8 s Delay 0.9 s Delay 1.0 s Delay 1.5 s Delay 2.0 s Delay 3.0 s 2bright pint TW200 IP MK II LED PAR...
  • Page 54 Delay 10 s 141…255 Default setting of the device LED repetition rate 000…010 No function 011…020 900 Hz 021…030 1,000 Hz 031…040 1,100 Hz 041…050 1,200 Hz 051…060 1,300 Hz 061…070 1,400 Hz 2bright pint TW200 IP MK II LED PAR...
  • Page 55: Functions In 8-Channel Dmx Mode

    Functions in 8-channel DMX mode Channel Value Function 000…255 Intensity of the master dimmer from dark (0) to light (255) 000…255 Cold white intensity (0% to 100%) 000…255 Warm white intensity (0% to 100%) 2bright pint TW200 IP MK II LED PAR...
  • Page 56 LED on 000…255 Blinder mode (0% to 100%), overwrites all dimmer channels Colour temperature from 2.700 K to 7.000 K 000…035 2,700 K 036…040 2,800 K 041…045 2,900 K 046…050 3,000 K 2bright pint TW200 IP MK II LED PAR...
  • Page 57 3,600 K 081…085 3,700 K 086…090 3,800 K 091…095 3,900 K 096…100 4,000 K 101…105 4,100 K 106…110 4,200 K 111…115 4,300 K 116…120 4,400 K 121…125 4,500 K 126…130 4,600 K 2bright pint TW200 IP MK II LED PAR...
  • Page 58 5,200 K 166…170 5,300 K 171…175 5,400 K 176…180 5,500 K 181…185 5,600 K 186…190 5,700 K 191…195 5,800 K 196…200 5,900 K 201…205 6,000 K 206…210 6,100 K 211…215 6,200 K 2bright pint TW200 IP MK II LED PAR...
  • Page 59 Dimmer curves 000…010 Default setting of the device 011…020 Dimmer curve ‘Linear’ 021…040 Dimmer curve ‘Stage’ 041…060 Dimmer curve ‘TV’ 061…080 Dimmer curve ‘Architectural’ 081…100 Dimmer curve ‘Theatre’ 101…120 Dimmer curve ‘Stage2’ 2bright pint TW200 IP MK II LED PAR...
  • Page 60 Delay 0.5 s Delay 0.6 s Delay 0.7 s Delay 0.8 s Delay 0.9 s Delay 1.0 s Delay 1.5 s Delay 2.0 s Delay 3.0 s Delay 4.0 s Delay 5.0 s 2bright pint TW200 IP MK II LED PAR...
  • Page 61 Default setting of the device LED repetition rate 000…010 No function 011…020 900 Hz 021…030 1,000 Hz 031…040 1,100 Hz 041…050 1,200 Hz 051…060 1,300 Hz 061…070 1,400 Hz 071…080 1,500 Hz 081…090 2,500 Hz 2bright pint TW200 IP MK II LED PAR...
  • Page 62 Operating Channel Value Function 091…100 4,000 Hz 101…110 5,000 Hz 111…120 6,000 Hz 121…130 10,000 Hz 131…140 Default setting of the device 141…255 No function 2bright pint TW200 IP MK II LED PAR...
  • Page 63: Technical Specifications

    Output connections Power supply for further Lockable output socket devices Power Twist TR1 IP65 DMX control XLR panel-mounted coupling (IP65), 3-pin Power consumption 135 W Supply voltage 100 - 240 V 50/60 Hz 2bright pint TW200 IP MK II LED PAR...
  • Page 64 Hanging, standing Dimensions 234 mm × 308 mm × 249 mm (W × H × D), with bracket Weight 4.2 kg Ambient conditions Temperature range 0 °C…40 °C Relative humidity 20%…80% (non-condensing) 2bright pint TW200 IP MK II LED PAR...
  • Page 65: Further Information

    Technical specifications Further information Design Outdoor housing, cannon Number of LEDs Colour mix CW / WW LED type Floor housing Fanless Remote control Wireless DMX Housing colour Black 2bright pint TW200 IP MK II LED PAR...
  • Page 66: Plug And Connection Assignments

    The unit offers a 3-pin XLR socket for DMX output and a 3-pin XLR plug for DMX input. Please refer to the drawing and table below for the pin assignment of a suitable XLR plug. Configuration Ground, shielding Signal inverted (DMX–, ‘cold signal’) Signal (DMX+, ‘hot signal’) 2bright pint TW200 IP MK II LED PAR...
  • Page 67: Troubleshooting

    Use special DMX cables for the wiring instead of normal microphone cables. In the following we list a few common problems that may occur during operation. We give you some suggestions for easy troubleshooting: 2bright pint TW200 IP MK II LED PAR...
  • Page 68 DMX mode on another device. If the procedures recommended above do not succeed, please contact our Service Center. You can find the contact information at www.thomann.de. 2bright pint TW200 IP MK II LED PAR...
  • Page 69: Cleaning

    Before cleaning, switch off the device and disconnect mains-operated devices from the mains. Only use pH-neutral, solvent-free and non-abrasive cleaning agents. Clean the unit with a slightly damp lint-free cloth. 2bright pint TW200 IP MK II LED PAR...
  • Page 70: Protecting The Environment

    Do not dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the instructions and markings on the packaging. Observe the disposal note regarding documentation in France. 2bright pint TW200 IP MK II LED PAR...
  • Page 71 Repairing a device or passing it on to another user is an ecologically valuable alternative to disposal. For example, use the classified ads of Thomann GmbH. If your old device contains personal data, delete those data before disposing of it. 2bright pint TW200 IP MK II LED PAR...
  • Page 72 Notes 2bright pint TW200 IP MK II LED PAR...
  • Page 73 Notes 2bright pint TW200 IP MK II LED PAR...
  • Page 74 Notes 2bright pint TW200 IP MK II LED PAR...
  • Page 76 Musikhaus Thomann · Hans-Thomann-Straße 1 · 96138 Burgebrach · Germany · www.thomann.de...

This manual is also suitable for:

556156

Table of Contents