Table of Contents

Advertisement

Quick Links

INTRODUCTION
This Owner's Manual has been prepared with the assis-
tance of service and engineering specialists to acquaint
you with the operation and maintenance of your vehicle.
It is supplemented by a Warranty and Maintenance
Information Booklet, located on the DVD, and various
customer-oriented documents. Please take the time to
read these publications carefully. Following the instruc-
tions and recommendations in this manual will help
assure safe and enjoyable operation of your vehicle.
NOTE: After you read the manual, it should be stored
in the vehicle for convenient referencing and remain
with the vehicle when sold, so that the new owner will
be aware of all safety warnings.
When it comes to service, remember that your authorized
dealer knows your vehicle best, has the factory-trained
technicians and genuine Volkswagen parts, and is inter-
ested in your satisfaction.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Routan 2010 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Volkswagen Routan 2010

  • Page 1 This Owner’s Manual has been prepared with the assis- dealer knows your vehicle best, has the factory-trained tance of service and engineering specialists to acquaint technicians and genuine Volkswagen parts, and is inter- you with the operation and maintenance of your vehicle. ested in your satisfaction.
  • Page 2: How To Use This Manual

    HOW TO USE THIS MANUAL Consult the following table for a description of the Consult the Table of Contents to determine which section symbols that may be used on your vehicle or throughout contains the information you desire. this Owner’s Manual: The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects.
  • Page 3: Warnings And Cautions

    WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
  • Page 4: Vehicle Identification Number

    VEHICLE IDENTIFICATION NUMBER NOTE: It is illegal to remove or alter the VIN. The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears on the Auto- mobile Information Disclosure Label affixed to a window on your vehicle, the vehicle registration and title.
  • Page 5: Vehicle Modifications/Alterations

    VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
  • Page 6: A Word About Your Keys

    A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the Key Fob into the ignition switch with either side up.
  • Page 7 Removing Key Fob From Ignition CAUTION! Place the shift lever in PARK. Turn the ignition key to the OFF position and then remove the Key Fob. An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all doors NOTE: Power window switches will also remain active when leaving the vehicle unattended.
  • Page 8 SENTRY KEY it indicates that someone used an invalid Key Fob to start The Sentry Key Immobilizer system prevents unautho- the engine. Either of these conditions will result in the rized vehicle operation by disabling the engine. The engine being shut off after two seconds. system does not need to be armed or activated.
  • Page 9: Vehicle Security Alarm - If Equipped

    VEHICLE SECURITY ALARM — IF EQUIPPED Arming The System The Vehicle Security Alarm monitors the vehicle doors Remove the key from the ignition switch and either press a power door lock switch while the driver or passenger for unauthorized entry and the ignition switch for unau- door is open, or press the LOCK button on the Remote thorized operation.
  • Page 10: Illuminated Entry - If Equipped

    ILLUMINATED ENTRY — IF EQUIPPED The courtesy lights will turn on when you use the Remote Keyless Entry (RKE) transmitter or open the doors. This feature is only available if you have RKE. The lights will fade to off after approximately 30 seconds or they will immediately fade to off once the ignition switch is turned ON.
  • Page 11: Remote Keyless Entry (Rke)

    equipped from the factory with three-button RKE trans- REMOTE KEYLESS ENTRY (RKE) This system allows you to lock or unlock the doors and mitters, and those built with power options will be liftgate, and activate the Panic Alarm, optional power equipped with up to seven-button RKE transmitters.
  • Page 12 1. Perform this operation while standing outside the Remote Open Window Feature vehicle. This feature allows you to remotely lower both front door windows at the same time. To use this feature, press and 2. Press the LOCK button for 4 to 10 seconds. release the UNLOCK button on the RKE transmitter and 3.
  • Page 13 If equipped with a rear interior switch on the left rear RKE transmitter is pushed while the door is being pillar, pushing this switch once will close the liftgate only. power-closed, the door will reverse to the full open The liftgate cannot be opened from this switch. position.
  • Page 14 General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
  • Page 15: Remote Starting System - If Equipped

    • Brake switch inactive (brake pedal not pressed) REMOTE STARTING SYSTEM — IF EQUIPPED This system uses the Remote Keyless Entry • Ignition key removed from ignition switch (RKE) transmitter to start the engine conve- • Battery at an acceptable charge level niently from outside the vehicle while still maintaining security.
  • Page 16 • The shift lever is moved out of PARK NOTE: • The ignition switch must be in the ON position in • The engine is allowed to run for the entire 15-minute order to drive the vehicle. cycle • For vehicles equipped with the Electronic Vehicle To Turn Off the Engine While in Remote Start Information Center (EVIC), the message “Insert Key/ Mode...
  • Page 17: Door Locks

    DOOR LOCKS If the lock plunger is down when you shut the door, the door will lock. Therefore, make sure the keys are not Manual Door Locks inside the vehicle before closing the door. Lock the doors by pushing down on the lock plungers on each door trim panel.
  • Page 18 operate. A chime will sound if the Key Fob is in the If you press the power door lock switch while the sliding ignition switch and a door is open, as a reminder to door is open, the sliding door will lock. remove the Key Fob.
  • Page 19 1. Enter your vehicle and close all doors. 8. If a chime is not heard, the program mode was canceled before the feature could be changed. If neces- 2. Fasten your seat belt. (Fastening the seat belt will sary, repeat this procedure. cancel any chimes that may be confusing during this programming procedure.) The Unlock Doors Automatically On Exit feature can be...
  • Page 20 WINDOWS Power Windows You can control either the front or rear windows using Power Vent Windows switches located on the driver’s door trim panel. The Switches on the driver’s door trim panel let the driver switches will operate only when the ignition switch is in operate the two vent windows from the driver’s seat.
  • Page 21 Front Passenger Power Window Switch There is a single switch on the front passenger’s door trim panel which operates the passenger door window and locks and unlocks all doors. The switch will operate only when the ignition switch is in the ON or ACC position and during power accessory delay.
  • Page 22 2. Push the window switch down firmly to the second detent to open the window completely and continue to hold the switch down for an additional two seconds after the window is fully open. Sliding Side Door Power Window Switch — If Equipped Second row passengers may power the sliding door window by a single switch on the door handle assembly.
  • Page 23: Sliding Side Door

    SLIDING SIDE DOOR door after the hold-open latch is activated, you must The sliding door may be opened from the inside or the rock the inside handle forward or pull outward on the outside. Pull outward on the exterior handle to open the exterior handle.
  • Page 24 To avoid unintentional operation of the power sliding door switch is pressed. To close the door, wait until it doors from the rear seats, press the power sliding door is fully open and then press the switch again. master lock button, located in the overhead console, to •...
  • Page 25 Sliding Side Door Child Protection Lock To provide a safer environment for small children riding in the rear seats, the sliding doors are equipped with a Child Protection Door Lock system. NOTE: When the Child Protection Door Lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position.
  • Page 26 NOTE: • After setting the Child Protection Door Lock system, always test the door from the inside to make certain it is in the desired position. • The power sliding side door switches will not open the power sliding doors if the vehicle is in gear or the vehicle speed is above 0 mph (0 km/h).
  • Page 27 LIFTGATE The liftgate can be unlocked using the Remote Keyless Entry (RKE) transmitter or by activating the power door lock switches located on either interior front door trim panel. Once unlocked, the liftgate can be opened or closed. To open the liftgate, pull the release handle while raising the liftgate with one fluid motion.
  • Page 28 The power liftgate may be closed by pressing the button, When the RKE transmitter button is pressed and the located in the upper left trim in the liftgate opening. Flash Lights feature is enabled, the tail lights will flash to Pushing once will only close the liftgate.
  • Page 29: Occupant Restraints

    • An energy-absorbing steering column and steering OCCUPANT RESTRAINTS Some of the most important safety features in your wheel vehicle are the restraint systems: • Knee bolsters/blockers for front seat occupants • Front seat belts incorporate pretensioners to enhance • Three-point lap and shoulder belts for all seating occupant protection by managing occupant energy positions during an impact event —...
  • Page 30 you under normal conditions. But in a collision, the belt WARNING! (Continued) will lock and reduce the risk of you striking the inside of • Wearing a seat belt incorrectly is dangerous. Seat the vehicle or being thrown out. belts are designed to go around the large bones of your body.
  • Page 31 3. When the belt is long enough to fit, insert the latch WARNING! plate into the buckle until you hear a “click”. • A belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury.
  • Page 32 6. To release the belt, push the red button on the buckle. WARNING! The belt will automatically retract to its stowed position. • A lap belt worn too high can increase the risk of If necessary, slide the latch plate down the webbing to allow the belt to retract fully.
  • Page 33 3. Allow the belt to retract. As the belt retracts, you will Automatic Locking Retractors (ALR) Mode — If Equipped hear a clicking sound. This indicates the safety belt is In this mode, the shoulder belt is automatically pre- now in the Automatic Locking Mode. locked.
  • Page 34 CAUTION! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision.
  • Page 35 AHR In Reset Position 3 — Final Downward Movement To Engage Locking Mecha- nism NOTE: • If you have difficulties or problems resetting the head 4. The AHR front soft foam and trim half should lock restraints, see an authorized dealer. into the back decorative plastic half.
  • Page 36 3. Within 60 seconds of turning the ignition switch to the Seat Belts and Pregnant Women ON/RUN position, unbuckle and then re-buckle the We recommend that pregnant women use the seat belts driver’s seat belt at least three times within 60 seconds, throughout their pregnancies.
  • Page 37 The Advanced Front Airbags have a multistage inflator NOTE: • Airbag covers may not be obvious in the interior trim; design. This allows the airbag to have different rates of inflation based on the severity and type of collision. but they will open during airbag deployment. •...
  • Page 38 Supplemental Seat-Mounted Side Airbags — If WARNING! Equipped • No objects should be placed over or near the Supplemental seat-mounted side airbags provide en- hanced protection to help protect an occupant during a airbag on the instrument panel, because any such side impact.
  • Page 39 Knee Impact Bolsters WARNING! The Knee Impact Bolsters help protect the knees of the driver and the front passenger, and position everyone for Infants in rear-facing child restraints should NEVER the best interaction with the Advanced Front Airbags. ride in the front seat of a vehicle with a passenger front airbag.
  • Page 40 The Advanced Front Airbags will not deploy in all frontal Airbag Deployment Sensors and Controls collisions, including some that may produce substantial Occupant Restraint Controller (ORC) vehicle damage — for example, some pole collisions, The ORC is part of a Federally regulated safety system truck underrides, and angle offset collisions.
  • Page 41 the Advanced Front Airbags. Different airbag inflation The ORC determines if a side collision requires the side rates are possible, based on the collision type and sever- airbags to inflate based on the severity and type of ity. The steering wheel hub trim cover and the upper collision.
  • Page 42 • Cut off fuel to the engine. • The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and front • Flash hazard lights as long as the battery has power or passenger as the airbags deploy and unfold. The until the ignition key is turned off.
  • Page 43 In the event of a collision, your vehicle is designed to used by Volkswagen Group of America, Inc.and others to record up to five seconds of specific vehicle data param- learn more about the possible causes of crashes and...
  • Page 44 Confidential • Engine RPM data will not be disclosed by Volkswagen Group of • Brake switch status America, Inc. to any third party except when: •...
  • Page 45 • The infant carrier is only used rearward-facing in the Older Children and Child Restraints vehicle. It is recommended for children who weigh up Children who weigh more than 20 lbs (9 kg) and who are to about 20 lbs (9 kg). Convertible child seats can be older than one year can ride forward-facing in the used either rearward-facing or forward-facing in the vehicle.
  • Page 46 Here are some tips on getting the most out of your child shoulder portion of the lap/shoulder belt will tighten restraint: the belt. The cinching latch plate will keep the belt tight; however, any seat belt system will loosen with •...
  • Page 47 third row fold-in-floor seats are equipped with a child NOTE: • When using the LATCH attaching system to install a restraint tether anchor at the center seating position. child restraint, please ensure that all seat belts not We urge you to follow the manufacturer’s directions being used for occupant restraints are stowed and out carefully when installing your child restraint.
  • Page 48 4. Tighten the lower attachment strap while firmly push- Installing the Top Tether Strap (with either Lower ing the child restraint rearward and downward into the Anchors or Vehicle Seat Belt): vehicle seat. Remove all slack in the lower attachment 1.
  • Page 49 Seat belts, except for the driver seat belt, are equipped Once you have completed securing the child restraint with an Automatic Locking Retractor (ALR) and/or a with the seat belt secure the top tether strap. Refer to cinching latch plate. Both types of seat belts are designed Installing the Top Tether Strap for instructions.
  • Page 50: Engine Break-In Recommendations

    ENGINE BREAK-IN RECOMMENDATIONS A new engine may consume some oil during its first few A long break-in period is not required for the engine and thousand miles (kilometers) of operation. This should be drivetrain (transmission and axle) in your vehicle. considered a normal part of the break-in and not inter- preted as an indication of difficulty.
  • Page 51: Safety Tips

    SAFETY TIPS WARNING! (Continued) Transporting Passengers • Be sure everyone in your vehicle is in a seat and NEVER TRANSPORT PASSENGERS IN THE CARGO using a seat belt properly. AREA. Exhaust Gas WARNING! WARNING! • Do not leave children or animals inside parked vehicles in hot weather.
  • Page 52 authorized dealer. If the light stays on, flickers, or comes WARNING! on while driving, have the system checked by an autho- rized dealer. Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- Defroster sonal injury.
  • Page 53 Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid, or brake fluid leaks are suspected, the cause should be located and corrected immediately.
  • Page 54 MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).
  • Page 55 mirror selection. Press the mirror select switch again to WARNING! guard against accidentally moving a mirror position. The mirror selection will also automatically turn off after Vehicles and other objects seen in a outside convex 30 seconds. mirrors will look smaller and farther away than they really are.
  • Page 56 Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is located on the sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights turn on automati- cally. Closing the mirror cover turns off the lights. Illuminated Mirror...
  • Page 57 Uconnect™ Phone — IF EQUIPPED features Bluetooth technology - the global standard that Uconnect™ Phone is a voice-activated, hands-free, in- enables different electronic devices to connect to each vehicle communications system. Uconnect™ Phone al- other without wires or a docking station, so Uconnect™ lows you to dial a phone number with your cellular Phone works no matter where you stow your cellular phone using simple voice commands (e.g., Call”...
  • Page 58 • For certain operations, compound commands can be Help Command used. For example, instead of saying Setup and then If you need assistance at any prompt, or if you want to Phone Pairing, the following compound command know your options at any prompt, say Help following can be said: Setup Phone Pairing.
  • Page 59 • The system will prompt you to say the name of the Dial by Saying a Number person you want to call. • Press the button to begin. • After the Ready prompt and the following beep, say • After the Ready prompt and the following beep, say the name of the person you want to call.
  • Page 60 • Automatic download and update, if supported, begins • This downloaded phonebook cannot be edited or as soon as the phone Bluetooth wireless connection is deleted on the Uconnect™ Phone. These can only be made to the Uconnect™ Phone. For example, after you edited on the mobile phone.
  • Page 61 • After you enter the Phonebook Delete menu, you will After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in then be asked for the name of the entry that you wish the phonebook, call the number you just edited, or return to delete.
  • Page 62 cellular service plan. For example, if your cellular service call waiting that you normally hear when using your plan provides three-way calling, this feature can be cellular phone. Press the button to place the current accessed through the Uconnect™ Phone. Check with call on hold and answer the incoming call.
  • Page 63 Redial ends, or until the vehicle battery condition dictates cessation of the call on the Uconnect™ Phone and • Press the button to begin. transfer of the call to the mobile phone. • After the Ready prompt and the following beep, say •...
  • Page 64 • If supported, this number may be programmable on • If supported, this number may be programmable on some systems. To do this, press button and say some systems. To do this, press the button and ‘Setup’, followed by ‘Emergency’. say ‘Setup’, followed by ‘Towing Assistance’.
  • Page 65 a , you could press the button and say, Pair a status when you are attempting to make a phone call using Uconnect™ Phone. The status is given for roaming, Phone to select that option without having to listen to network signal strength, phone battery strength, etc.
  • Page 66 • After the Ready prompt and the following beep, say List Paired Cellular Phone Names Setup Select Phone and follow the prompts. • Press the button to begin. • You can also press the button at any time while • After the “Ready” prompt and the following beep, say the list is being played, and then choose the phone that “Setup Phone Pairing.”...
  • Page 67 • fully closed windows, Voice Command • For best performance, adjust the rearview mirror to • dry weather condition. provide at least ⁄ in (1 cm) gap between the overhead • Even though the system is designed for users speaking console (if equipped) and the mirror.
  • Page 68 Bluetooth Communication Link Power-Up Cellular phones have been found to lose connection to After switching the ignition key from OFF to either ON the Uconnect™ Phone. When this happens, the connec- or ACC position, or after a language change, you must tion can generally be reestablished by switching the wait at least five seconds prior to using the system.
  • Page 70 Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) zero call cancel confirmation prompts three continue four delete five dial download seven edit eight emergency nine English star (*) erase all plus (+) Espanol pound (#) Francais add location help home Voice Commands Voice Commands Primary...
  • Page 71 • This device may not cause harmful interference. General Information This device complies with Part 15 of the FCC rules and • This device must accept any interference received, RSS 210 of Industry Canada. Operation is subject to the including interference that may cause undesired following conditions: operation.
  • Page 72: Voice Command - If Equipped

    When you press the Voice Command button, you VOICE COMMAND — IF EQUIPPED will hear a beep. The beep is your signal to give a Voice Command System Operation command. This Voice Command system allows you to control your AM, FM radio, satellite radio, disc NOTE: If you do not say a command within a few player, and a memo recorder.
  • Page 73 In this mode, you can say the following commands: Radio FM To switch to the FM band, say “FM” or “Radio FM”. In • “Radio” (to switch to the radio mode) this mode, you may say the following commands: • “Disc” (to switch to the disc mode) •...
  • Page 74 − “Previous” (to play the previous memo) NOTE: Keep in mind that you have to press the Voice Command button first and wait for the beep − “Delete” (to delete a memo) before speaking the “Barge In” commands. • “Delete All” (to delete all memos) Voice Training System Setup For users experiencing difficulty with the system recog-...
  • Page 75 SEATS Seats are a primary part of the Occupant Restraint System of the vehicle. They need to be used properly for safe operation of the vehicle. WARNING! • DO NOT allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
  • Page 76 then push back to the desired position and release the WARNING! lever. Lean forward and lift the lever to return the seatback to its normal position. Using body pressure, lean Adjusting a seat while the vehicle is moving is forward and rearward on the seat to be sure the seatback dangerous.
  • Page 77 To raise the head restraint, pull upward on the head Adjusting Head Restraints Head restraints can reduce the risk of injury in the event restraint (on some models, you may need to press the of a rear impact. The head restraint should be adjusted so push button).
  • Page 78 • In the event of deployment of an Active Head Re- WARNING! (Continued) straint, refer to “Occupant Restraints/Resetting Active • Do not place items over the top of the Active Head Head Restraints (AHR)” in “Things to Know Before Restraint, such as coats, seat covers or portable Starting Your Vehicle”...
  • Page 79 WARNING! CAUTION! • Persons who are unable to feel pain to the skin Repeated overheating of the seat could damage the because of advanced age, chronic illness, diabetes, heating element and/or degrade the material of the spinal cord injury, medication, alcohol use, ex- seat.
  • Page 80 NOTE: Be sure that the seatback is locked into the upright position. Forward Folding Second Row Seats To provide additional space behind the second row seats, the seats can be folded forward. With the seat in its fold-flat position, pull upward on the easy-access release lever and lift the seat into the desired position.
  • Page 81 Secure the retainer strap to the inside grab handle located WARNING! on the B-Pillar. When not in use, store the strap in the sewn-in pocket located on the base of the seat cushion. To reduce the risk of personal injury: •...
  • Page 82 Third Row Power Seat — If Equipped The third row power seat offers the following features: • The seatbacks can be folded forward for additional cargo space if needed. • Head restraints can be stowed with the seat. • Tailgate mode flips the seat rearward to face out the tailgate.
  • Page 83 NOTE: • To abort seat operation while seat is in motion, press a different seat position selector switch to stop the seat. Once the seat stops moving, then the desired position can be selected. • The third row power seat system includes obstacle detection for safe operation.
  • Page 84 4. Pull release strap marked “3” and tumble the seat 2. Pull release strap marked “1” to unlock the recliner. rearward into the storage bin. 3. Pulling strap “3” releases the seatback to return to its full upright position. 4. Adjust the head restraint to the desired position. WARNING! In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor...
  • Page 85: Driver Memory Seat - If Equipped

    DRIVER MEMORY SEAT — IF EQUIPPED The Memory Buttons 1 and 2 on the driver’s door panel can be programmed to recall the driver’s seat, driver’s outside mirror, adjustable brake and accelerator pedals, and radio station preset settings. Your Remote Keyless Entry (RKE) transmitters can also be programmed to recall the same positions when the UNLOCK button is pressed.
  • Page 86 to “Electronic Vehicle Information Center (EVIC)/ To recall the memory setting for driver two, press Customer-Programmable Features” in “Understanding MEMORY button 2 on the driver’s door or the UNLOCK Your Instrument Panel” for further information. button on the RKE transmitter linked to Memory Position 12.
  • Page 87 • When you remove the key from the ignition switch the Each stored memory setting will have an associated Easy driver seat will move to a position 0.3 in (7.7 mm) Entry and Easy Exit Position. forward of the rear stop if the driver seat position is NOTE: The Easy Entry/Easy Exit feature can be en- between 0.9 –...
  • Page 88: To Open And Close The Hood

    TO OPEN AND CLOSE THE HOOD 2. Move to the front of the vehicle and look inside the To open the hood, two latches must be released. center of the hood opening. Locate then push the safety catch lever up toward your right while raising the hood 1.
  • Page 89 LIGHTS Interior Lighting All of the lights, except the Hazard Warning lights, Interior lights are turned on when a door or the liftgate is headlight high beams and flash-to-pass, are controlled by opened, the Remote Keyless Entry (RKE) transmitter is switches to the left of the steering column on the instru- activated, or when the dimmer control is moved to the ment panel.
  • Page 90 Parking Lights headlights will stay on for up to 90 seconds after you turn Turn the headlight switch knob to the first detent the ignition switch OFF. To turn the Automatic System to turn the parking lights on. This also turns on all off, turn the headlight switch clockwise to the “O”...
  • Page 91 Lights-On Reminder Front Fog Lights — If Equipped If the headlights or the parking lights are left on, or if the To activate the front fog lights, turn on the parking dimmer control is in the extreme top position after the lights or the low beam headlights and push in the ignition switch is turned OFF, a chime will sound when headlight switch control knob.
  • Page 92 Lane Change Assist Flash-To-Pass Tap the lever up or down once, without moving beyond You can signal another vehicle with your headlights by the detent, and the turn signal (right or left) will flash lightly pulling the multifunction lever toward you. This three times then automatically turn off.
  • Page 93: Windshield Wiper And Washers

    WINDSHIELD WIPER AND WASHERS The wipers and washers are operated by a switch within the multifunction lever. Rotate the end of the multifunc- tion lever to select the desired wiper speed. NOTE: Always remove any buildup of snow that pre- vents the windshield wiper blades from returning to the off position.
  • Page 94 3. Rear Wiper and Washer Rotating the rotary ring to the first detent activates the rear intermittent wipers. To activate the washers, rotate the rotary ring fully forward and the washers will spray until the ring is released, and then resume the intermit- tent interval.
  • Page 95: Tilt Steering Column

    TILT STEERING COLUMN To tilt the column, pull the lever downward (located on the steering column and below the steering wheel) to the open position. You may then position the steering wheel up or down, as desired. Pull the small lever upward to the closed position to lock the steering wheel firmly in place.
  • Page 96: Adjustable Pedals - If Equipped

    ADJUSTABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward or away from the driver to provide improved position with the steering wheel. The adjust- able pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat positions.
  • Page 97: Electronic Speed Control - If Equipped

    ELECTRONIC SPEED CONTROL — IF EQUIPPED down if multiple Speed Control functions are operated When engaged, Electronic Speed Control takes over the simultaneously. If this occurs, the Electronic Speed Con- accelerator operation at speeds greater than 25 mph trol System can be reactivated by pushing the Electronic (40 km/h).
  • Page 98 increase. Each time the lever is tapped speed increases, so NOTE: The Electronic Speed Control system maintains tapping the lever three times will increase speed by speed up and down hills. A slight speed change on 3 mph (4.8 km/h), etc. moderate hills is normal.
  • Page 99: Rear Park Assist - If Equipped

    REAR PARK ASSIST — IF EQUIPPED Rear Park Assist Sensors The Rear Park Assist System provides visual and audible The four Rear Park Assist sensors, located in the rear indications of the distance between the rear fascia and the fascia/bumper, monitor the area behind the vehicle that detected obstacle when backing up.
  • Page 100 Park Assist Disabled Slow Tone The system will indicate a detected obstacle by showing three solid arcs and will produce a ⁄ second tone. As the vehicle moves closer to the object the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.
  • Page 101: Audible Signal

    WARNING DISPLAY DISTANCES DISPLAY MESSAGE OBSTACLE DISTANCE FROM: ARC’s AUDIBLE SIGNAL REAR CORNERS REAR CENTER Park Assist ON None None Warning Object Detected 78.7 in (200 cm) 3 Solid Yes, 1/2 second Warning Object Detected 39.3 in (100 cm) 3 Flashing Slow Tone Warning Object Detected 27.5 in (70 cm)
  • Page 102 • When you turn off the Rear Park Assist System, the • Clean the Rear Park Assist Sensors regularly, taking instrument cluster will display “PARK ASSIST DIS- care not to scratch or damage them. The sensors must ABLED.” Furthermore, once you turn off the Rear not be covered with ice, snow, slush, mud, dirt, or Park Assist System, it remains off until you turn it on debris.
  • Page 103 WARNING! (Continued) • Before using the Rear Park Assist System, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the ve- hicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear fascia when the warning display turns on the single...
  • Page 104: Rear Back Up Camera - If Equipped

    REAR BACK UP CAMERA — IF EQUIPPED CAUTION! Your vehicle may be equipped with a Rear Back Up • To avoid vehicle damage, the Rear Back Up Cam- Camera System that allows you to see an on-screen image of the rear of your vehicle whenever the shift lever is put era System should only be used as a parking aid.
  • Page 105: Overhead Consoles

    OVERHEAD CONSOLES Front Overhead Console Two versions of the overhead console are available. The base front overhead console models feature fixed incan- descent courtesy/reading lights, flip-down sunglass stor- age and conversation mirror. Premium front overhead console models feature a LED focused light that illumi- nates the instrument panel cup holders, Infrared Auto- matic Temperature Control Sensor (ATC equipped only), two swiveling LED lights, flip-down sunglass storage,...
  • Page 106 Rear Courtesy/Reading Lights — If Equipped The overhead console has two sets of courtesy lights. The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry (RKE), the lights will also turn on when the UNLOCK button on the RKE transmitter is pressed.
  • Page 107: Garage Door Opener - If Equipped

    GARAGE DOOR OPENER — IF EQUIPPED HomeLink replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink unit operates off your vehicle’s battery. The HomeLink buttons that are located in the headliner or sun visor designate the three different HomeLink channels.
  • Page 108 • After training a HomeLink channel, if the garage Place the handheld transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink button you wish to program while door does not operate with HomeLink and the ga- keeping the indicator light in view.
  • Page 109 Using HomeLink Gate Operator/Canadian Programming To operate, press and release the programmed Canadian radio frequency laws require transmitter sig- HomeLink button. Activation will now occur for the nals to time-out (or quit) after several seconds of trans- trained device (i.e., garage door opener, gate operator, mission –...
  • Page 110 2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: • The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for com- pliance could void the user’s authority to operate the device.
  • Page 111: Power Sunroof - If Equipped

    POWER SUNROOF — IF EQUIPPED Power Sunroof Operation The power sunroof control switch is located in the front Opening the Sunroof Manually overhead console. The sunroof panel tilts upward at the Press the switch rearward and hold, and the sunroof will rear for ventilation or slides rearward under the roof.
  • Page 112 Express-Close Auto-Express with Anti–Pinch Protection Press the switch forward and release, and the sunroof During express closing, anytime an obstacle that restricts will close automatically from any position. The sunroof glass movement is detected, the motor will stop and will close fully, then stop automatically. This is called reverse travel to avoid pinching the object.
  • Page 113: Electrical Power Outlets - If Equipped

    ELECTRICAL POWER OUTLETS — IF EQUIPPED Two 12 Volt (13 Amp) power outlets are located on the lower instrument panel next to the open storage bin. The left side power outlet is controlled by the ignition switch and the right side outlet is connected directly to the battery.
  • Page 114 CAUTION! CAUTION! (Continued) • Power outlets are designed for accessory plugs • Many accessories that can be plugged in draw only. Do not hang any type of accessory or acces- power from the vehicle’s battery, even when not in sory bracket from the plug. Improper use of the use (i.e., cellular phones, etc.).
  • Page 115: Power Inverter - If Equipped

    POWER INVERTER — IF EQUIPPED A 110 Volt (150 Watt) inverter outlet (if equipped) con- verts DC current to AC current, and is located on the left rear trim panel immediately behind the second row left passenger seat. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts.
  • Page 116 CAUTION! (Continued) • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly. Only use these inter- mittently and with greater caution. • After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the...
  • Page 117: Cup Holders

    CUPHOLDERS There are nine cupholders in the interior. Two cupholders in the center front instrument panel, four in the floor consoles and three more are located in the third row quarter trim panel. All liners are removable for cleaning. Pull the flexible liner from the cupholder drawer or tray starting at one edge for easy removal.
  • Page 118 STORAGE Glove Compartments Upper Glove Compartment To open the upper compartment, press upward on the release button (1), the door will open automatically. To close the compartment door, push firmly downward on the doors surface until latched. Glove Compartment Features 1 —...
  • Page 119 Driver Seatback Storage — As Equipped Umbrella Holder The drivers seat back has a primary storage pocket on all An umbrella holder has been conveniently molded into models and an optional secondary mesh pocket. the left front door entry scuff molding. Driver’s Seatback Storage Umbrella Holder 1 —...
  • Page 120 Storage Bin Safety Warning WARNING! (Continued) Carefully follow these warnings to help prevent personal • Do not operate the storage bin covers while the injury or damage to your vehicle: vehicle is in motion. • Do not use a storage bin latch as a tie down. WARNING! •...
  • Page 121 Rear Compartment Storage Coat Hooks Your vehicle is equipped with open storage areas located Coat hooks are located along the headliner for the third in each rear trim panel. row seating positions. CAUTION! The coat hook load limit is 10 lbs (4.5 kg). Exceeding the recommended load limit can cause the coat hooks to break or disengage from the vehicle.
  • Page 122: Console Features

    CONSOLE FEATURES There are two consoles available: Basic and Premium. Basic Console Basic console features consist of the following: • The basic console profile allows vehicle occupants to easily pass through the first row to the second. • Four cupholders accept up to extra large size beverage cups or 20 oz (.6 L) plastic bottles.
  • Page 123 • Large center console will store headphones for the available rear DVD entertainment system or other items. • 12 Volt DC Power Outlet provides continuous power inside the console for cellular phones or other electron- ics. • Rear occupant accessible. •...
  • Page 124 Position 2 shows the raised storage tray revealing a large Dual Storage Bins storage area below. Position 3 shows the top portion of the console in a rearward position. This is accomplished by lifting the upper most latch at the front of the console. This provides easy access to the storage area below and provides two of the four cupholders for the second row passengers.
  • Page 125 • Pull up on the console to be sure it is firmly latched. WARNING! • In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched. •...
  • Page 126: Rear Window Defroster

    REAR WINDOW DEFROSTER CAUTION! (Continued) The rear window defroster button is located on • Use care when washing the inside of the rear front of the climate control panel. Press this button window. Do not use abrasive window cleaners on to turn on the rear window defroster and the heated the interior surface of the window.
  • Page 127: Load Leveling System - If Equipped

    LOAD-LEVELING SYSTEM — IF EQUIPPED WARNING! The automatic load-leveling system will provide a level riding vehicle under most passenger and cargo loading Do not install a load-leveling system on vehicles that conditions. are not equipped with Anti-Lock Brakes. Vehicles without Anti-Lock Brakes (ABS) have a height- A hydraulic pump contained within the shock absorbers sensing proportioning valve.
  • Page 128: Roof Luggage Rack - If Equipped

    ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and side rails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. Distribute cargo weight evenly on the roof rack crossbars.
  • Page 129 WARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in per- sonal injury or property damage. Follow the Roof Rack Cautions when carrying cargo on your roof rack.
  • Page 130: Sun Screens - If Equipped

    SUN SCREENS — IF EQUIPPED Gently pull up on the tab to raise the sun screen. Sun screens are available for second and third row Continue pulling the sun screen until the tab is near the seating windows. The screens store in the sill trim panels, top of the window.
  • Page 131: Instrument Panel Features

    INSTRUMENT PANEL FEATURES 1 — Air Vent 5 — Upper Glove Compartment 9 — Cup Holders 13 — Ignition Switch 2 — Instrument Cluster 6 — Lower Glove Compartment 10 — Storage Bin 14 — Headlight Switch 3 — Shift Lever 7 —...
  • Page 132: Instrument Cluster

    INSTRUMENT CLUSTER...
  • Page 133: Instrument Cluster Descriptions

    INSTRUMENT CLUSTER DESCRIPTIONS CAUTION! 1. Temperature Gauge Driving with a hot engine cooling system could The temperature gauge shows engine coolant tem- damage your vehicle. If temperature gauge reads perature. Any reading within the normal range “280“, pull over and stop the vehicle. Idle the vehicle indicates that the engine cooling system is operat- with the air conditioner turned off until the pointer ing satisfactorily.
  • Page 134 driving, turn off some of the vehicle’s non-essential vehicle placard or tire inflation pressure label, you should electrical devices or increase engine speed (if at idle). If determine the proper tire inflation pressure for those the charging system light remains on, it means that the tires.) vehicle is experiencing a problem with the charging As an added safety feature, your vehicle has been...
  • Page 135 is started. If the light turns on while driving, stop the 9. Turn Signal Indicators vehicle and shut off the engine as soon as possible. A The arrow will flash with the exterior turn signal chime will sound for four minutes when this light turns when the turn signal lever is operated.
  • Page 136 indicated by the Brake Warning Light which will turn on Vehicles equipped with the Anti-Lock Brake System when the brake fluid level in the master cylinder has (ABS), are also equipped with Electronic Brake Force dropped below a specified level. Distribution (EBD).
  • Page 137 17. Seat Belt Reminder Light Certain conditions such as a loose or missing gas cap, When the ignition switch is first turned ON, this poor fuel quality, etc., may illuminate the MIL after light will turn on for five to eight seconds as a bulb engine start.
  • Page 138 (gATE, gASCAP, noFUSE, CHangE OIL, LoCOOL, Lo- gATE ......Lift Gate Ajar WASH, etc.), push and hold the button until the display LoW tirE.
  • Page 139 damaged, a “noFUSE” message will display in the odom- 1. Turn the ignition switch to the ON position (Do not eter display area. For further information on fuses and start the engine). fuse locations refer to “Fuses” in “Maintaining Your 2.
  • Page 140: Compass Mini-Trip Computer (Cmtc) - If Equipped

    COMPASS MINI-TRIP COMPUTER (CMTC) — IF be driven several minutes before the updated tempera- EQUIPPED ture is displayed. Engine temperature can also affect the displayed temperature, therefore temperature readings NOTE: are not updated when the vehicle is not moving. • The compass on your vehicle is self-calibrating, elimi- nating the need to manually calibrate the compass.
  • Page 141 Compass/Temperature Display and such devices may interfere and cause false com- pass readings. Compass Variance Compass Variance is the difference between Magnetic North and Geographic North. To ensure compass accu- racy, the compass variance should be properly set accord- ing to the variance map for the zone where the vehicle will be driven.
  • Page 142: Electronic Vehicle Information Center (Evic) - If Equipped

    ELECTRONIC VEHICLE INFORMATION CENTER NOTE: The compass on your vehicle is self-calibrating, (EVIC) — IF EQUIPPED eliminating the need to manually calibrate the compass. The Electronic Vehicle Information Center (EVIC) fea- This system conveniently allows the driver to select a tures a driver-interactive display that is located in the variety of useful information by pressing the switches instrument cluster.
  • Page 143 • Left Front Turn Signal Light Out Electronic Vehicle Information Center (EVIC) Displays • Left Rear Turn Signal Light Out When the appropriate conditions exist, the EVIC displays • Right Front Turn Signal Light Out the following messages: • Door(s) Ajar (with a single chime if vehicle is in •...
  • Page 144 determined by a weighted average of the instantaneous Display Units of Measure in: and average fuel economy, according to the current fuel To make your selection, press and release the STEP tank level. button until “ENGLISH” or “METRIC” appears. NOTE: Significant changes in driving style or vehicle To Reset The Display loading will greatly affect the actual drivable distance of Reset will only occur while a resettable function is being...
  • Page 145 5. Complete one or more 360° turns (in an area free from large metal or metallic objects) until the CAL indicator turns off. The compass will now function normally. Compass Variance Compass Variance is the difference between Magnetic North and Geographic North. To ensure compass accu- racy, the compass variance should be properly set accord- ing to the variance map for the zone where the vehicle will be driven.
  • Page 146 Auto UNLK On Exit RKE Linked To Memory When ON is selected, all doors will unlock when the When this feature is selected the memory seat, mirror, vehicle is stopped and the transmission is in the PARK or and radio settings will return to the memory set position NEUTRAL position and the driver’s door is opened.
  • Page 147: Illumin. Approach

    ILLUMIN. Approach Display Units of Measure in When this feature is selected, the headlights will activate The EVIC, odometer, and navigation system (if and remain on for up to 90 seconds when the doors are equipped) can be changed between English and Metric unlocked with the RKE transmitter.
  • Page 148 SALES CODE REQ (8YD) — AM/FM STEREO Operating Instructions - Radio Mode RADIO AND 6–DISC CD/DVD CHANGER NOTE: The ignition switch must be in the ON or ACC (MP3/WMA AUX JACK) position to operate the radio. NOTE: The radio sales code is located on the lower right Power Switch/Volume Control (Rotary) side of the radio faceplate.
  • Page 149 3. After adjusting the hours, press the right side TUNE/ RW/FF SCROLL control knob to set the minutes. The minutes Pressing the RW (Rewind) or FF (Fast Forward) buttons will begin to blink. causes the tuner to search for the next frequency in the direction of the arrows.
  • Page 150 16-Digit Character Dis- 16-Digit Character Dis- Program Type Program Type play play Jazz Jazz Top 40 Top 40 News News Weather Weather Nostalgia Nostalga By pressing the SEEK button when the Music Type icon Oldies Oldies is displayed, the radio will be tuned to the next frequency Personality Persnlty station with the same selected Music Type name.
  • Page 151 • VES™ CH1/CH2 - Allows the user to change the Enter the four-digit country code using the TUNE/ mode of either the IR1 or IR2 wireless headphones by SCROLL control knob to scroll up and down to select the pressing the AUDIO/SELECT button (if equipped). number and then push to select.
  • Page 152 the SET button twice and SET 2 will show in the display Operation Instructions - (DISC MODE for CD and window. Each button can be set for SET 1 and SET 2 in MP3/WMA Audio Play, DVD-VIDEO) both AM and FM. This allows a total of 12 AM, 12 FM, The radio DVD player and many DVD discs are coded by and 12 Satellite (if equipped) stations to be stored into geographic region.
  • Page 153 SCAN Button (CD MODE) Notes On Playing MP3/WMA Files Press the SCAN button to scan through each track on the The radio can play MP3/WMA files; however, acceptable CD currently playing. MP3/WMA file recording media and formats are limited. When writing MP3/WMA files, pay attention to the TIME Button (CD MODE) following restrictions.
  • Page 154 Playback of MP3/WMA Files MPEG Specifi- Sampling Fre- Bit Rate (kbps) When a medium containing MP3/WMA data is loaded, cation quency (kHz) the radio checks all files on the medium. If the medium 320, 256, 224, contains a lot of folders or files, the radio will take more MPEG-1 Audio 192, 160, 128, 48, 44.1, 32...
  • Page 155 SCAN Button (Auxiliary Mode) Operating Instructions — Voice Command System No function. (If Equipped) For the radio, refer to “Voice Command” in “Understand- EJECT Button (Auxiliary Mode) ing The Features Of Your Vehicle”. No function. For Uconnect™ “Voice Command,” refer to “Uconnect™ Phone”...
  • Page 156 SATELLITE RADIO — IF EQUIPPED REN information, call the toll-free number 888-539-SIRI (888- (8AY)/REQ (8YD)/RER (8YS)/RES (8AG) RADIOS 539-7474), or visit the Sirius web site at www.sirius.com, ONLY or at www.siriuscanada.ca for Canadian residents. Satellite radio uses direct satellite-to-receiver broadcast- Electronic Serial Number/Sirius Identification ing technology to provide clear digital sound, coast to Number (ESN/SID)
  • Page 157 Operating Instructions — Satellite Mode INFO Button Pressing the INFO button will cycle the display informa- NOTE: The ignition switch must be in the ON or ACC tion between Artist, Song Title, and Composer (if avail- position to operate the radio. able).
  • Page 158 pushbutton memory. The channels stored in SET 2 Operating Instructions — Uconnect™ Phone (If memory can be selected by pressing the pushbutton Equipped) twice. Refer to “Uconnect™ Phone” in “Understanding The Features Of Your Vehicle”. Every time a preset button is used, a corresponding button number will display.
  • Page 159 • Nine different medias to choose from in each screen VIDEO ENTERTAINMENT SYSTEM (VES)™ — IF EQUIPPED (AM, FM, Sirius Radio, DVD1, DVD2, Hard Disc Drive The optional Video Entertainment System (VES)™ is (HDD), AUX in radio, AUX1, AUX2) available with: The LCD screen(s) are located in the overhead compart- •...
  • Page 160: Remote Sound System Controls - If Equipped

    REMOTE SOUND SYSTEM CONTROLS — IF The right-hand rocker switch has a pushbutton in the EQUIPPED center, and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume. Pressing the bottom of the rocker switch will decrease the volume.
  • Page 161: Cd/Dvd Disc Maintenance

    CD/DVD DISC MAINTENANCE NOTE: If you experience difficulty in playing a particu- To keep a CD/DVD in good condition, take the following lar disc, it may be damaged (i.e., scratched, reflective precautions: coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding.
  • Page 162: Radio Operation And Cellular Phones

    RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being on in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
  • Page 163: Climate Controls

    CLIMATE CONTROLS The Climate Control System allows you to regulate the temperature, amount, and direction of air circulating throughout the vehicle. The controls are located on the instrument panel, below the radio. Manual Heating, Ventilation and Air Conditioning (HVAC) System The controls for the manual HVAC system in this vehicle consist of a series of outer rotary dials and inner push knobs.
  • Page 164 Mode Control (Air Direction) air goes to the floor outlets. This feature gives improved Mode control allows you to choose comfort during sunny but cool conditions. from several patterns of air distribu- Floor Mode tion. You can select either a primary Air is directed through the floor outlets with a mode, as identified by the symbols, or small amount through the defrost and side window...
  • Page 165 Air Outlets Air Conditioning Operation The airflow from each of the instrument panel outlets can Push on this button to engage the Air be adjusted for direction, and turned on or off to control Conditioning (A/C). A light will illu- airflow.
  • Page 166 The Three-Zone Basic Temperature Control bottom panel The primary control for the rear blower is on the front controls rear Heating, Ventilation, and Air Conditioning climate control unit located on the instrument panel. (HVAC) operations. The Three-Zone Basic Temperature Control bottom panel has five positions;...
  • Page 167 Rear Temperature Control control is in FLOOR, DEFROST, or MIX modes, airflow When the blower knob on the front climate control unit is will be directed out of the rear floor outlets. set to any position other than RR , the rear temperature Rear Mode Control settings will be controlled by the rear temperature control knob on the front climate control unit.
  • Page 168 Front Upper ATC Panel Front Lower ATC Panel 1 - System On/Off 9 - Air Conditioning (A/C) 1 - Blower Speed 4 - Rear HVAC Lock On/Off 2 - Rear Temperature / Rear 5 - Rear DEFROST 2 - Front Blower Indicator 10 - AUTO Mode / Blower System On/Off 3 - Left Front Temperature...
  • Page 169 Manual Operation Panel Mode This system offers a full complement of manual override Air comes from the outlets in the instrument panel. features. The AUTO symbol in the front ATC display will Each of these outlets can be individually adjusted to be turned off when the system is being used in the direct the flow of air.
  • Page 170 a second time to turn off the RECIRCULATION mode The REAR SYSTEM control for the Rear ATC System is LED and allow outside air into the vehicle. on the front lower ATC panel located on the instrument panel. NOTE: In cold weather, use of the RECIRCULATION mode may lead to excessive window fogging.
  • Page 171 • The temperature can be displayed in U.S. or Metric CAUTION! units by selecting the US/M customer-programmable feature. Refer to the “Electronic Vehicle Information Interior air enters the Rear Automatic Three Zone Center (EVIC) — Customer-Programmable Features” Temperature Control (ATC) system through an intake in this Section of the manual.
  • Page 172 Winter Operation Window Fogging To ensure the best possible heater and defroster perfor- Vehicle windows tend to fog on the inside in mild, rainy mance, make sure the engine cooling system is function- and/or humid weather. To clear the windows, select ing properly and the proper amount, type, and concen- DEFROST or MIX mode and increase the front blower tration of coolant is used.
  • Page 173 A/C Air Filter— If Equipped On vehicles equipped with Automatic Three Zone Tem- perature Control (ATC), the climate control system filters out dust and pollen from the air. Refer to “Air Condi- tioning” in “Maintaining Your Vehicle” for filter replace- ment instructions.
  • Page 174 SALES CODE RER (8YS)/REN (8AY)/RBZ (8YT ) — Operating Instructions — Voice Command AM/FM STEREO RADIO AND CD/DVD/HDD/NAV — System — If Equipped IF EQUIPPED For the radio, refer to “Voice Command” in “Understand- ing The Features Of Your Vehicle”. NOTE: The sales code is located on the lower right side of the unit’s faceplate.
  • Page 175 Changing the Time Zone satellite clock is Greenwich Mean Time (GMT). This is the worldwide standard for time. This makes the system’s 1. Turn on the radio. clock very accurate once the appropriate time zone and 2. Touch the screen where the time is displayed. The daylight savings information is set.
  • Page 176 Changing the Time Zone 1. Turn on the multimedia system. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. Touch the screen where the words “Set Time Zone” are displayed. The time zone selection menu will appear on the screen.
  • Page 177 SALES CODE RES (8AG) — AM/FM STEREO Operating Instructions — Radio Mode RADIO WITH CD PLAYER (MP3 AUX JACK) NOTE: The ignition switch must be in the ON or ACC NOTE: The radio sales code is located on the lower right position to operate the radio.
  • Page 178 Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the AM/FM Button mid-range tones.
  • Page 179 If you insert a disc with the ignition ON and the radio EJECT Button - Ejecting a CD ON, the unit will switch from radio to CD mode and Press the EJECT button to eject the CD. begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds.
  • Page 180 The radio uses the following limits for file systems: Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal • Maximum number of folder levels: 8 CD audio tracks and computer files (including MP3 files). •...
  • Page 181 Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device, such as an MP3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.
  • Page 182: Starting Procedures

    STARTING PROCEDURES Automatic Transmission Before starting your vehicle, adjust your seat, adjust the The shift lever must be in the NEUTRAL or PARK inside and outside mirrors, fasten your seat belt, and if position before you can start the engine. Press the brake present, instruct all other occupants to buckle their seat pedal before shifting into any driving gear.
  • Page 183 WARNING! (Continued) CAUTION! • If the vehicle has a discharged battery, booster To prevent damage to the starter, DO NOT crank the cables may be used to obtain a start from a booster engine for more than 15 seconds. Wait 10 to 15 sec- battery or the battery in another vehicle.
  • Page 184: Engine Block Heater - If Equipped

    ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms the engine, and permits quicker starts in cold weather. Connect the electrical cord to a standard 110-115 Volt AC electrical outlet with a grounded, three-wire extension cord. The engine block heater cord is routed under the hood on the driver’s side of the vehicle.
  • Page 185: Automatic Transmission

    AUTOMATIC TRANSMISSION WARNING! CAUTION! It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle Damage to the transmission may occur if the follow- speed. If your foot is not firmly on the brake pedal, ing precautions are not observed: the vehicle could accelerate quickly forward or in •...
  • Page 186 self-calibrating; therefore, the first few shifts on a new by moving the lever—/ + while in the DRIVE position, vehicle may be somewhat abrupt. This is a normal the instrument cluster will display transmission gear condition, and precision shifts will develop within a few selection as 6, 5, 4, 3, 2, 1 for six-speed transmissions.
  • Page 187 • Look at the shift indicator window on the console to NEUTRAL ensure the shift lever is in the PARK position. This range is used when vehicle is standing for pro- longed periods with engine running. Engine may be • When engaged in PARK, you will not be able to move started in this range.
  • Page 188 In the event of a momentary problem, the transmission Odometer Screen can be reset to regain all forward gears by performing the Display following steps: Actual Gear(s) Al- 1-2 1-3 1-4 1-5 1-6 1-6 lowed (Six-Speed 1. Stop the vehicle. Transmission) 2.
  • Page 189: Driving On Slippery Surfaces

    DRIVING ON SLIPPERY SURFACES Traction When driving on wet or slushy roads, it is possible for a Acceleration layer of water to build up between the tire and road Rapid acceleration on snow covered, wet, or other slip- surface. This is known as hydroplaning and may cause pery surfaces may cause the front wheels to pull errati- partial or complete loss of vehicle control and stopping cally to the right or left.
  • Page 190: Driving Through Water

    DRIVING THROUGH WATER Shallow Standing Water Driving through water more than a few inches/ Although your vehicle is capable of driving through centimeters deep will require extra caution to ensure shallow standing water, consider the following Caution safety and prevent damage to your vehicle. and Warning before doing so.
  • Page 191: Parking Brake

    PARKING BRAKE Before leaving the vehicle, make sure that the parking brake is fully applied and place the shift lever in the PARK position. The foot operated parking brake is positioned below the lower left corner of the instrument panel. To apply the park brake, firmly push the park brake pedal fully.
  • Page 192 CAUTION! If the Brake System Warning Light remains on with the parking brake released, a brake system malfunc- tion is indicated. Have the brake system serviced by an authorized dealer immediately.
  • Page 193: Anti-Lock Brake System (Abs)

    • A slight drop or fall away of the brake pedal at the end ANTI-LOCK BRAKE SYSTEM (ABS) The Anti-Lock Brake System (ABS) provides increased of the stop vehicle stability and brake performance under most WARNING! braking conditions. The system operates with a separate computer to modulate hydraulic pressure to prevent •...
  • Page 194 If both the “Brake Warning Light” and the “Anti-Lock Brake Warning Light” remain on, the ABS and Electronic Brake Force Distribution (EBD) systems are not function- ing. Immediate repair to the ABS system is required. Consult with your authorized dealer service center as soon as possible.
  • Page 195: Power Steering

    POWER STEERING system. This noise should be considered normal, and it does not in any way damage the steering system. The standard power steering system will give you good vehicle response and increased ease of maneuverability WARNING! in tight spaces. The system will provide mechanical steering capability if power assist is lost.
  • Page 196: Electronic Brake Control System

    ELECTRONIC BRAKE CONTROL SYSTEM will allow more engine torque to be applied to the wheel Your vehicle is equipped with an advanced electronic that is not spinning. This feature remains active even if brake control system that includes the Traction Control the ESP is in the “Partial Off”...
  • Page 197 the intended path, ESP applies the brake of the appropri- WARNING! (Continued) ate wheel to assist in counteracting the oversteer or • The capabilities of a BAS-equipped vehicle must understeer condition. never be exploited in a reckless or dangerous • Oversteer - when the vehicle is turning more than manner which could jeopardize the user’s safety appropriate for the steering wheel position.
  • Page 198 NOTE: • The “ESP/TCS Indicator Light” and the “ESP/BAS Warning Light” come on momentarily, each time the ignition switch is turned ON. • Each time the ignition is turned ON, the ESP System will be ON, even if it was turned off previously. •...
  • Page 199: Tire Safety Information

    TIRE SAFETY INFORMATION NOTE: • P (Passenger) - Metric tire sizing is based on U.S. Tire Markings design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards.
  • Page 200 EXAMPLE: 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
  • Page 201 Tire Terminology and Definitions Term Definition B-Pillar The vehicle B-Pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold Tire Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
  • Page 202 To determine the maximum loading conditions of your 3) tire size designed for your vehicle vehicle, locate the statement “The combined weight of 4) cold tire inflation pressures for the front, rear, and occupants and cargo should never exceed XXX lbs or spare tires.
  • Page 203 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them.
  • Page 204: Tires - General Information

    TIRES — GENERAL INFORMATION WARNING! (Continued) Tire Pressure • Unequal tire pressures can cause steering prob- Proper tire inflation pressure is essential to the safe and lems. You could lose control of your vehicle. satisfactory operation of your vehicle. Three primary •...
  • Page 205 Tire pressures change by approximately 1 psi (7 kPa) per loading may be required for high-speed vehicle opera- 12° F (7° C) of air temperature change. Keep this in mind tion. Refer to original-equipment information, or an when checking tire pressure inside a garage, especially in authorized tire dealer, for recommended safe operating the Winter.
  • Page 206 CAUTION! WARNING! • Fast spinning tires can be dangerous. Forces gen- Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the erated by excessive wheel speeds may cause tire compact spare installed. Damage to the vehicle may damage or failure.
  • Page 207 Replacement Tires WARNING! The tires on your new vehicle provide a balance of many • Do not use a tire, wheel size or rating other than characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manu- that specified for your vehicle.
  • Page 208: Snow Tires

    SNOW TIRES Some areas of the country require the use of snow tires during Winter. Standard tires are of the all-season type and satisfy this requirement as indicated by the M+S designation on the tire sidewall. If you need snow tires, select tires equivalent in size and type to the original equipment tires.
  • Page 209: Tire Rotation Recommendations

    The suggested rotation method is shown in the following TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at diagram. different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates, and tend to develop irregular wear pat- terns.
  • Page 210: Tire Pressure Monitor System (Tpms)

    TIRE PRESSURE MONITOR SYSTEM (TPMS) The TPMS will warn the driver of a low tire pressure if The TPMS will warn the driver of a low tire pressure the tire pressure falls below the low pressure warning based on the cold inflation tire pressure requirements threshold for any reason, including low temperature found on the tire placard located on the driver’s-side effects, or natural air pressure loss through the tire.
  • Page 211 • Seasonal temperature changes will affect tire pressure, NOTE: • The TPMS is not intended to replace normal tire care and the TPMS will monitor the actual tire pressure in and maintenance, or to provide warning of a tire the tire. failure or condition.
  • Page 212 Vehicles with Compact Spare tire, the TPMS will automatically update, and the “TPMS Telltale Warning Light” will turn off as long as no tire 1. The compact spare tire (if equipped) does not have a pressure is below the low-pressure warning limit in any TPMS sensor.
  • Page 213 the “TPMS Telltale Warning Light” will extinguish once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) to receive this information. Check TPMS Message The “TPMS Telltale Warning Light” will flash on and off for 75 seconds, and remain on solid when a system fault is detected.
  • Page 214 • This device must accept any interference received, 5. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the compact spare, including interference that may cause undesired the TPMS will update automatically. In addition, the operation.
  • Page 215: Fuel Requirements

    FUEL REQUIREMENTS for optimum performance. The use of premium gasoline is not recommended, as it will not provide any benefit 3.8L Engine over regular gasoline in these engines. All engines are designed to meet all emis- sions regulations and provide excellent Light spark knock at low engine speeds is not harmful to fuel economy and performance when us- your engine.
  • Page 216 If a Non-FFV vehicle is inadvertently fueled with E-85 More extensive repairs will be required for prolonged fuel, the engine will have some or all of these symptoms: exposure to E-85 fuel. • operate in a lean mode MMT In Gasoline MMT is a manganese containing metallic additive that is •...
  • Page 217 NOTE: Intentional tampering with emissions control WARNING! (Continued) systems can result in civil penalties being assessed • Guard against carbon monoxide with proper against you. maintenance. Have the exhaust system inspected Carbon Monoxide Warnings every time the vehicle is raised. Have any abnor- mal conditions repaired promptly.
  • Page 218: Adding Fuel

    NOTE: The driver’s side sliding door cannot be opened ADDING FUEL while the fuel door is open. This feature operates only Fuel Filler Cap (Gas Cap) when the sliding door is fully closed prior to opening the The gas cap is located behind the fuel filler door on the fuel door.
  • Page 219: Vehicle Loading

    • Vehicle Identification Number (VIN) VEHICLE LOADING As required by National Highway Traffic Safety Admin- • Type of Vehicle istration regulations, your vehicle has a certification label • Month, Day and Hour of Manufacture (MDH) affixed to the driver’s side door or B-Pillar. If seats are removed for carrying cargo, do not exceed the The bar code allows a computer scanner to read the specified GVWR and GAWR.
  • Page 220 Figure out the weight on the front and rear of the vehicle CAUTION! separately. It is important that you distribute the load evenly over the front and rear axles. Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, Overloading can cause potential safety hazards and parts on your vehicle can break, or it can change the shorten useful service life.
  • Page 221: Trailer Towing

    TRAILER TOWING that you do not exceed the GVWR. Refer to “Vehicle In this section you will find safety tips and information Loading/Vehicle Certification Label” in “Starting and on limits to the type of towing you can reasonably do Operating” for further information. with your vehicle.
  • Page 222 Weight-Distributing Hitch WARNING! A weight-distributing system works by applying lever- • An improperly adjusted Weight Distributing age through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue weight to the Hitch system may reduce handling, stability, brak- tow vehicle’s front axle and the trailer’s axle(s).
  • Page 223: Trailer Hitch Classifications

    The Trailer Hitch Classification chart provides the indus- try standard for the maximum trailer weight a given trailer hitch class can tow, and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. TRAILER HITCH CLASSIFICATIONS Class Max.
  • Page 224 Trailer and Trailer Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to severely sway side-to-side, which will cause loss of control of the vehicle and trailer.
  • Page 225 WARNING! (Continued) WARNING! (Continued) • Make certain that the load is secured in the trailer • Vehicles with trailers should not be parked on a and will not shift during travel. When trailering grade. When parking, apply the parking brake on cargo that is not fully secured, dynamic load shifts the tow vehicle.
  • Page 226 • An electronically actuated trailer brake controller is WARNING! required when towing a trailer with electronically • Do not connect trailer brakes to your vehicle’s actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic hydraulic brake lines.
  • Page 227 Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. Automatic Transmission The DRIVE gear can be selected when towing. However, if frequent shifting occurs while in DRIVE, fifth gear (with six-speed transmission) should be selected.
  • Page 228: Recreational Towing (Behind Motorhome, Etc.)

    RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) CAUTION! Towing this vehicle behind another vehicle (flat- towing with all four wheels on the ground) is not recommended. NOTE: If the vehicle requires towing, make sure all four wheels are off the ground.
  • Page 229: Hazard Warning Flasher

    HAZARD WARNING FLASHER NOTE: With extended use, the Hazard Warning flasher The Hazard Warning flasher switch is located in the may wear down your battery. center of the instrument panel above the radio. Press the switch to turn on the Hazard Warning flasher.
  • Page 230: If Your Engine Overheats

    IF YOUR ENGINE OVERHEATS to high. This allows the heater core to act as a In any of the following situations, you can reduce the supplement to the radiator and aids in removing heat potential for overheating by taking the appropriate ac- from the engine cooling system.
  • Page 231: Jacking And Tire Changing

    JACKING AND TIRE CHANGING WARNING! (Continued) Jack Location • If it is necessary to retrieve the spare tire from under the vehicle on the side of the vehicle close to WARNING! moving traffic, pull far enough off the road to avoid the danger of being hit.
  • Page 232 Preparations For Jacking 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.
  • Page 233 2. To remove the compact spare tire/cover assembly, WARNING! (Continued) assemble the winch handle extensions to form a “T’ and • If working on or near a roadway, be extremely fit the winch “T” handle over the drive nut. Rotate the careful of motor traffic.
  • Page 234 • Front jack location is on the sill flange of the vehicle body and aligns with the front door edge. Squeezing Winch Retainer Tabs Jack Locations 5. There are two jack engagement locations on each side of the vehicle body. These locations are on the sill flange CAUTION! of the vehicle body.
  • Page 235 11. Finish tightening the wheel lug nuts. Push down on deflated tire in the spare tire location. Have the full the wrench while tightening for increased leverage. Al- sized tire repaired or replaced as soon as possible. ternate wheel lug nuts until each nut has been tightened 14.
  • Page 236 3. Using the winch “T” handle, rotate the drive nut to the CAUTION! right until the compact spare tire/cover assembly is drawn into place against the underside of the vehicle. The compact spare tire cover assembly must be used when the compact spare tire is stored. Failure to use 4.
  • Page 237: Jump-Starting Procedure

    JUMP-STARTING PROCEDURE WARNING! If your vehicle has a discharged battery it can be jump- started using a set of jumper cables and a battery in Do not attempt jump-starting if the battery is frozen. another vehicle or by using a portable battery booster It could rupture or explode and cause personal injury.
  • Page 238 3. If using another vehicle to jump-start the battery, park CAUTION! the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. Failure to follow these procedures could result in damage to the charging system of the booster vehicle WARNING! or the discharged vehicle.
  • Page 239: Freeing A Stuck Vehicle

    FREEING A STUCK VEHICLE CAUTION! (Continued) If your vehicle becomes stuck in mud, sand or snow, it • Revving the engine or spinning the wheels too fast can often be moved by a rocking motion. Turn your may lead to transmission overheating and failure. steering wheel right and left to clear the area around the It can also damage the tires.
  • Page 240: Towing A Disabled Vehicle

    TOWING A DISABLED VEHICLE CAUTION! Towing With The Ignition Key • Do not attempt to tow this vehicle from the front Your vehicle may be towed under the following condi- with sling-type towing equipment. Damage to the tions: front fascia will result. •...
  • Page 241: Engine Compartment - 3.8L

    ENGINE COMPARTMENT — 3.8L 1 — Power Steering Fluid Reservoir 6 — Engine Coolant Reservoir 2 — Air Filter 7 — Engine Oil Fill 3 — Brake Fluid Reservoir 8 — Engine Oil Dipstick 4 — Battery 9 — Coolant Pressure Cap 5 —...
  • Page 242: Engine Compartment - 4.0L

    ENGINE COMPARTMENT — 4.0L 1 — Power Steering Fluid Reservoir 6 — Engine Coolant Reservoir 2 — Air Filter 7 — Engine Oil Dipstick 3 — Brake Fluid Reservoir 8 — Engine Oil Fill 4 — Battery 9 — Coolant Pressure Cap 5 —...
  • Page 243: Onboard Diagnostic System - Obd

    ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic further damage to the emission control system.
  • Page 244: Emissions Inspection And Maintenance Programs

    EMISSIONS INSPECTION AND MAINTENANCE Your vehicle has a simple ignition key-actuated test, PROGRAMS which you can use prior to going to the test station. To In some localities, it may be a legal requirement to pass check if your vehicle’s OBD II system is ready, you must an inspection of your vehicle’s emissions control system.
  • Page 245: Replacement Parts

    Use of genuine Volkswagen parts for normal/scheduled maintenance and repairs is highly recommended to en- sure the designed performance. Damage or failures caused by the use of non-Volkswagen parts for mainte- nance and repairs will not be covered by the manufac- turer’s warranty.
  • Page 246: Dealer Service

    DEALER SERVICE Your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these Service Manuals before attempting any procedure yourself.
  • Page 247: Maintenance Procedures

    Immediately have potential malfunctions Checking Oil Level examined by an authorized Volkswagen dealer or To assure proper engine lubrication, the engine oil must qualified repair center. be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop.
  • Page 248 Engine oil is an engineered product and its quality filters should be used to assure most efficient performance may be impaired by supplemental service. Volkswagen Genuine Parts, like the oil filter, are additives. recommended due to their high quality.
  • Page 249 The quality of replacement engine air filters varies con- cation or oil change. Replace as required. siderably. Only high quality filters should be used to assure most efficient service. Volkswagen Genuine Parts, like the air filter, are recommended due to their high quality.
  • Page 250 NOTE: Intentional tampering with emissions control To minimize the possibility of catalytic converter dam- systems can result in civil penalties being assessed age: against you. • Do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in WARNING! motion.
  • Page 251 Air Conditioner Maintenance WARNING! For best possible performance, your air conditioner • Use only refrigerants and compressor lubricants should be checked and serviced by an authorized dealer at the start of each warm season. This service should approved by the manufacturer for your air condi- include cleaning of the condenser fins and a system tioning system.
  • Page 252 CAUTION! The A/C air filter is labeled with an arrow to indicate airflow direction through the filter. Failure to prop- erly install the filter will result in the need to replace it more often. 7. Rotate the glove compartment door back into position. Body Lubrication Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate,...
  • Page 253 The washer fluid reservoir will hold a full gallon of fluid Cooling System when the “Low Washer Fluid Light” illuminates. WARNING! WARNING! • When working near the radiator cooling fan, dis- Commercially available windshield washer solvents connect the fan motor lead or turn the ignition are flammable.
  • Page 254 (antifreeze). When adding engine coolant (antifreeze), a minimum NOTE: Mixing engine coolant (antifreeze) types will solution of 50% recommended Volkswagen Genuine decrease the life of the engine coolant (antifreeze) and Parts Antifreeze/ Coolant Five Year/100,000 Mile For- will require more frequent engine coolant (antifreeze) mula HOAT (Hybrid Organic Additive Technology), or changes.
  • Page 255 rules for your community. To prevent ingestion by ani- WARNING! mals or children, do not store ethylene glycol-based • The warning words “DO NOT OPEN HOT” on engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground. If ingested by a child the cooling system pressure cap are a safety pre- or pet, seek emergency assistance immediately.
  • Page 256 • Keep the front of the radiator clean. If your vehicle is WARNING! equipped with air conditioning, keep the front of the condenser clean. Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting •...
  • Page 257 WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or • Do not allow petroleum based fluid to contami- moisture, use only new brake fluid or fluid that nate the brake fluid. Brake seal components could has been in a tightly closed container. Keep the be damaged, causing partial or complete brake master cylinder reservoir cap secured at all times.
  • Page 258 If the transmission is disassembled for any reason, the Appearance Care and Protection from Corrosion fluid and filter should be changed. Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- Special Additives Automatic Transmission Fluid (ATF) is an engineered graphic locations and usage.
  • Page 259 • If your vehicle is damaged due to an accident or heavy soil and/or excessive brake dust, use a nonabra- similar cause which destroys the paint and protective sive, non-acidic cleaner. Do not use scouring pads, steel coating, have your vehicle repaired as soon as pos- wool, a bristle brush, or metal polishes.
  • Page 260: Installation

    defrosters or the right rear quarter window equipped Seat Belt Maintenance with the radio antenna. Do not use scrapers or other Do not bleach, dye or clean the seatbelts with chemical sharp instruments which may scratch the elements. solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric.
  • Page 261 FUSES Totally Integrated Power Module (TIPM) The Totally Integrated Power Module (TIPM) is located in the engine compartment near the battery. Refer to “Engine Compartment” in “Maintaining Your Vehicle” for further information. This center contains cartridge fuses and mini-fuses. A label that identifies each compo- nent may be printed or embossed on the inside of the cover.
  • Page 262 FUSES/TIPM FUSES/TIPM Cartridge Cartridge Cavity Mini-Fuse Description Cavity Mini-Fuse Description Fuse Fuse 40 Amp — PZEV Motor/Flex 20 Amp — Powertrain Con- Green Fuel Blue trol Module (PCM) Trans 30 Amp — Headlamp Wash Range Pink Relay/Manifold Tuning Valve 60 Amp —...
  • Page 263 FUSES/TIPM FUSES/TIPM Cartridge Cartridge Cavity Mini-Fuse Description Cavity Mini-Fuse Description Fuse Fuse — 20 Amp Ignition Off Draw — 20 Amp Rear View Mirror Yellow – Cabin Compart- Yellow (RR VW MIR), ment Node (IOD- Cabin Compart- CCN), SIREN, ment Node Clock Module (CCN), Multi- (CLK MOD),...
  • Page 264 FUSES/TIPM FUSES/TIPM Cartridge Cartridge Cavity Mini-Fuse Description Cavity Mini-Fuse Description Fuse Fuse — 20 Amp Fuel Pump (FUEL — 10 Amp Next Generation Yellow PUMP), Diesel Lift Controller (NGC), Pump (DSL LIFT PCM, Transmis- PUMP) – Export sion Feed (TRANS Only FEED), TCM —...
  • Page 265 The heated mirrors, lower instrument panel power outlet FUSES/TIPM and removable floor console, when in the front position Cartridge Cavity Mini-Fuse Description are fused with self-resetting fuses that are only service- Fuse able by an authorized dealer. The power seats are fused —...
  • Page 266: Vehicle Storage

    VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days, you may want to take steps to protect your battery. You may do the following: • Remove the 20 Amp mini-fuse in the Totally Inte- grated Power Module (TIPM) labeled Ignition-Off Draw (IOD).
  • Page 267: Replacement Bulbs

    REPLACEMENT BULBS Park/Turn Signal ....3457NAK Front Side Marker..... . WY5W Headlamp –...
  • Page 268: Bulb Replacement

    BULB REPLACEMENT NOTE: On vehicles equipped with High Intensity Dis- charge Headlamps (HID), when the headlamps are High Intensity Discharge Headlamps (HID) — If turned on, there is a blue hue to the lights. This dimin- Equipped ishes and becomes more white after approximately The headlamps are a type of high voltage discharge tube.
  • Page 269 Rear Tail, Stop, Turn Signal, and Side Marker Lamps 1. Raise the liftgate. 2. Remove the tail lamp assembly by removing the two screws from the inboard side. Use a fiber stick or similar tool to gently pry the light on the outboard side to disengage the two ball studs.
  • Page 270: Fluid Capacities

    4.0 Liter Engine (SAE 10W-30, API Certified) 5.5 Quarts 5.2 Liters Cooling System * 3.8 and 4.0 Liter Engine (Volkswagen Engine Coolant/ 13.4 Quarts 12.6 Liters Antifreeze 5 Year/100,000 [160 000 km] Mile Formula) * Includes heater and coolant recovery bottle filled to MAX level. Add 2.9 Qts (2.8 L) if equipped with a rear...
  • Page 271: Fluids, Lubricants And Genuine Parts

    Volkswagen ATF+4 Automatic Transmission Fluid or equivalent licensed Automatic Transmission ATF+4 product. Volkswagen DOT 3 and SAE J1703 should be used or equivalent. If DOT Brake Master Cylinder 3 brake fluid is not available, then DOT 4 is acceptable. Use only recom- mended brake fluids.
  • Page 272: Emissions Control System Maintenance

    EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type, must be done at the times or mileages specified to ensure the continued proper functioning of the Emissions Con- trol System. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
  • Page 273: Suggestions For Obtaining Service For Your Vehicle

    SUGGESTIONS FOR OBTAINING SERVICE FOR Be Reasonable With Requests YOUR VEHICLE If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with Prepare For The Appointment the service advisor and list the items in order of priority. If you’re having warranty work done, be sure to have the At many authorized dealers, you may obtain a rental right papers with you.
  • Page 274: Warranty Information

    WARRANTY INFORMATION See the Warranty Information Booklet, located on the DVD, for the terms and provisions of Volkswagen war- ranties applicable to this vehicle and market.
  • Page 275 VOLKSWAGEN PARTS Genuine Volkswagen fluids, lubricants, parts, and acces- sories are available from an authorized dealer. They will help keep the vehicle operating at its best.
  • Page 276 VOLKSWAGEN SERVICE REPAIR MANUALS Volkswagen Service Manuals and Official Factory Repair Manuals are published as soon as possible after model introduction. To order service manuals and other Volkswagen Service literature contact: Volkswagen Technical Literature Ordering Center 1–800–544–8021 From 8:00 AM to 8:00 PM EST, Monday through Friday.
  • Page 277: Department Of Transportation Uniform Tire Quality Grades

    significantly from the norm due to variations in driving DEPARTMENT OF TRANSPORTATION UNIFORM habits, service practices, and differences in road charac- TIRE QUALITY GRADES The following tire grading categories were established by teristics and climate. the National Highway Traffic Safety Administration. The Traction Grades specific grade rating assigned by the tire’s manufacturer The Traction grades, from highest to lowest, are AA, A, B,...
  • Page 278: If You Need Assistance

    • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. Volkswagen Group of America, Inc. Customer CARE 3499 West Hamlin Road...

Table of Contents