Commercial copying, redistribution, hiring or lending is prohibited. No part of this publication may be stored in a retrieval system or transmitted in any other form or means without written permission from Draper Tools Limited. In all cases this copyright notice must remain intact.
This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms are not authorised. Your Draper guarantee is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the guarantee period.
INTRODUCTION 4.1 SCOPE For detail and finishing work such as sanding, cutting, scraping, etc. It is intended for domestic and light commercial use only. Any other application is considered misuse. 4.2 SPECIFICATION Stock no..........................83650 Part no.........................MT400QSF Rated voltage ......................230V~50Hz Rated input ........................
HEALTH & SAFETY INFORMATION 5.1 GENERAL SAFETY INSTRUCTIONS General Power Tools Safety Warnings Warning: Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool”...
HEALTH & SAFETY INFORMATION g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust related hazards. 4) Power Tool Use And Care a) Do not force the power tool.
HEALTH & SAFETY INFORMATION – Excessive force will reduce the working efficiency and cause motor overload. Replacing the accessory regularly will maintain optimum working efficiency. Maintain tool with care – NOTE: Remove plug from the socket before carrying out any adjustment, servicing or maintenance.
Lay the contents out and check them against the parts shown below. If any part is damaged or missing; please contact the Draper Help Line (the telephone number appears on the Title page) and do not attempt to use the multi-tool.
BASIC MULTI-TOOL OPERATIONS 8.1 ATTACHING THE SANDING BACKING PAD FIG.1 – FIGS. 1 – 3 NOTE: Switch off the Multi-Tool and remove the plug from the power socket before carrying out adjustments, servicing or maintenance. Caution: For all work or when changing application tools, always wear protective gloves.
BASIC MULTI-TOOL OPERATIONS 8.3 FITTING THE TOOL ATTACHMENTS FIG.5 – FIGS. 5 – 6 Warning: Before mounting or replacing application tools or accessories, switch off the power supply and remove the plug. This preventative safety measure eliminates danger from accidentally starting the power tool. (For illustrative purposes, the offset rigid scraper blade is depicted in figs.5 –...
BASIC MULTI-TOOL OPERATIONS 8.5 USING THE VARIABLE SPEED CONTROL – FIG. 7 Select oscillation frequency (speed) while the motor is running. The variable speed control can be used to set the optimum oscillating frequency according to the accessories used and the respective application. High oscillation frequency: Sanding, sawing, rasping and polishing stone and metal.
MAINTENANCE 9.1 MAINTENANCE & PARTS REPLACEMENT Regular inspection and cleaning reduces the necessity for maintenance operations and will keep your tool in good working condition. The motor must be correctly ventilated during tool operation. For this reason avoid blocking the air inlets. After use disconnect the tool from the power supply and vacuum the ventilation slots.
10. EXPLANATION OF SYMBOLS 10.1 EXPLANATION OF SYMBOLS Warning! Wear dust mask. Warning! Read the instruction manual Warning! Warning! Wear suitable eye/face Wear ear defenders. protection. WEEE Do not dispose of Waste Electrical & Electronic Equipment in with domestic rubbish Class II construction (Double insulated).
12. DISPOSAL 12.1 DISPOSAL – At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. – Contact your local authority for details of collection schemes in your area. In all circumstances: •...
Page 20
- Sales Desk: (023) 8049 4333 - General Enquiries: (023) 8026 6355 - Service/Warranty Repair Agent For aftersales servicing or warranty repairs, please contact the Draper Tools Help Line for details of an agent in your local area. YOUR DRAPER STOCKIST RDCH0816...
Need help?
Do you have a question about the STORMFORCE MT400QSF and is the answer not in the manual?
Questions and answers