Junghans Mega 1000 Manual
Hide thumbs
Also See for Mega 1000:
- Manual (173 pages) ,
- Operating instructions manual (153 pages) ,
- Manual (17 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Junghans Mega 1000
Summary of Contents for Junghans Mega 1000
- Page 1 Mega 1000 J604.64...
- Page 2 Reception test together, then it is a genuine Junghans. A watch for all those who live their own style – and on that we can not do other than congratulate you! Light >...
-
Page 3: Table Of Contents
Operating instructions Mega 1000 Content Page Radio technology Operational requirements Important notice concerning the display Automatic time synchronisation Please take note that during the time synchronisation, the display will au- Functions tomatically switch itself off and remain switched off for the duration of the Time display modes procedure. -
Page 4: Radio Technology
Junghans radio-controlled wristwatches automatically synchronise themsel- ves every day with the DCF77, WWVB, JJY40 and JJY60 time signal transmitters. If your Junghans Mega 1000 radio- controlled watch is unable to receive a signal due to interference (e.g. thunder storms, electronic devices, lighting dimmer switches) it will automatically attempt to receive a signal the follo- wing day at the same time. -
Page 5: Operational Requirements
(e.g. due to higher ambient temperature) you should For the USA’s WWVB time signal transmitter the following specific feature bring the watch to your specialist retailer or send it to the Junghans Service applies: Center within 2 weeks to have the battery replaced. -
Page 6: Functions
4. Functions Reception indicator The Junghans Mega 1000 has a variety of functions that are shown in the dis- play. The watch is operated using the five buttons above and below the display as well as on the side of the watch. -
Page 7: Additional Functions
4.2 Additional functions 5. Description of the functions and their operation The following functions can be selected one after the other using the T3 5.1 Stopwatch with split function (chrono) button. – Stopwatch with split function and split-time memory (chrono) Press T3 until CHRONO mode is selected. -
Page 8: Countdown Timer
5.2 Countdown timer When the stopwatch is running, pressing T2 shows Press T3 until TIMER mode is selected. the split time. These are shown in the upper part of the display. Pressing T2 again shows additional split times. The last ten split times are always saved. The stopwatch continues to run when split times are being shown. -
Page 9: Alarm
5.3 Alarm Your Mega 1000 provides you with the option of setting the alarm as a daily repeating alarm (24h alarm) or as a single alarm. Press T3 until ALARM mode is selected. Proceed as follows to set the type of alarm: Make sure that your Mega 1000 is in ALARM mode. -
Page 10: Reception Indicator
The indicator returns to 0 the next time the signal is successfully received. Your Junghans Mega 1000 first attempts to receive a signal from the transmit- ter station it last used to carry out a synchronisation. If the watch cannot re- 7. -
Page 11: Time Zone Adjustment/ 12-24 Hour Display / Home Time
8. Time zone adjustment/ 12-24 hour display / home time 8.1 Time zone adjustment The Junghans Mega 1000 can receive time signals from the DCF77, WWVB, JJY40 and JJY60 transmitter stations. This means that the watch will reliably To reset the main time to your home time (see chapter 8.3 ”home time”), press show daylight saving or winter time (except WWVB –... -
Page 12: Hour Display
8.2 12-24 hour display 8.3 Local time Once the desired 12-24 hour time display mode has Press T4 once the desired time zone has been set. You been set, press T4 to adjust the time. can now choose between the 12-hour time display (am/pm) and the 24-hour time display. -
Page 13: Language Selection (Weekday Indicator And Date Display)
9. Language selection (weekday indicator and date display) 9.2 Date display The language of the weekday indicator of your Junghans Mega 1000 has been set to German at the factory. The language can be set to English or French in The date can be displayed either in day-month the time/date display modes (time display mode 2 or 3). -
Page 14: Nd Time
11. Restart / Starting up procedure 10. 2 Time The 2 time function enables you to show an additional time in the display After changing the battery, a restart is automatically that is independent of the main time (e.g. when you want to see your home carried out. -
Page 15: Manual Start
If the watch does not successfully receive a signal When the watch is in manual start mode the settings that need to be adju- for a long period of time then the reception pro- sted (hour, minute, second, 12-24 hour display, language, date display mode, cess is stopped to save battery power. -
Page 16: Illumination
First check whether your 14. Button lock Mega 1000 is in one of the 5 time display modes. If this is not the case, press To prevent unintentional adjustment of the display, your Mega 1000 has a the T3 button until the current time is shown in the display. -
Page 17: Impermeability
Marking Instructions for use ences, which can cause moisture to enter the watch. We therefore recommend regular checkups by a Junghans specialist. Servicing and bracelet repairs should also be carried out by an authorised Junghans Diving service partner. Washing, without... -
Page 18: Technical Information
Operating temperature 0° to + 50° C Free of charge and FTZ approve. We reserve the right to make technical changes. Declaration of Conformity Uhrenfabrik Junghans GmbH & herewith decla- res that this wristwatch conforms to the principle requirements and other relevant stipulations of Directive R&TTE2014/53/EU.
Need help?
Do you have a question about the Mega 1000 and is the answer not in the manual?
Questions and answers