Do you have a question about the 58500E and is the answer not in the manual?
Questions and answers
Brad Anderson
May 30, 2025
Water is leaking right below valve where the 6 screws hold the top on. I removed & there is no seal...tightened it back up & still leaking.
1 comments:
Mr. Anderson
May 30, 2025
To fix a water leak near the valve on a Bestway 58500E where the screws hold the top on, check the following:
- Ensure the control valve is not set between two functions. Set it to one function only. - Inspect the gasket or O-ring near the valve area. If it is broken or out of place, replace or reposition it. - Tighten any loose screws or hose connections near the valve. - If leakage is from Port D, make sure the cap is installed and the gasket is in good condition. Replace the gasket if necessary.
Page 1
Trademarks used in some countries under license from / Manufactured by Bestway Inflatables & Material Corp., No. 208 Jin Yuan Wu Road, Shanghai, 201812, China (Tel: +86 21 69135588). Represented in North America by Bestway (USA) Inc., 3435 S. McQueen Road, Chandler, AZ 85286, United States of America. www.bestwayusa.com...
OWNER’S MANUAL 58500E Sand Filter WE SUGGEST NOT TO RETURN THE PRODUCT TO THE STORE QUESTIONS? PROBLEMS? Visit the Bestway YouTube channel MISSING PARTS? For FAQ, Manuals, Videos Or Spare Parts, Please Visit bestwayusa.com/support SAFETY INFORMATION WARNING IMPORTANT SAFETY INSTRUCTIONS...
Please examine and verify all sand filter components are present before use. Notify Bestway at the customer service address listed on this manual for any damaged or missing parts at the time of purchase.
Page 4
SAFETY INFORMATION harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver.
Page 5
SAFETY INFORMATION • Loose cover/grates and associated components shall be reattached before bathers are allowed to use the pool. • SOFA components and fastener receptacles shall be clean and free of debris or obstructions during installation of F4070-01 cover/grate and fasteners. •...
Page 8
For installation instructions, scan the QR code printed on the front cover or follow the illustrations below. Drawings are for illustration purposes only. May not reflect actual product. Not to scale. Bestway is not responsible for damage caused to the product due to mishandling or failure to follow these instructions.
Page 10
INSTALLATION 20sec AIR DISCHARGING OPERATION: Follow these steps to discharge air before switching the sand filter on and after every maintenance operation. Omitting this operation will greatly affect the lifespan of the product. NOTE: It is important to repeat this operation every time you start the pump after winterizing, any maintenance and backwashing the sand bed.
Page 12
INSTALLATION 20sec AIR DISCHARGING OPERATION: Follow these steps to discharge air before switching the sand filter on and after every maintenance operation. Omitting this operation will greatly affect the lifespan of the product. NOTE: It is important to repeat this operation every time you start the pump after winterizing, any maintenance and backwashing the sand bed.
Page 13
INSTALLATION 20sec AIR DISCHARGING OPERATION: Follow these steps to discharge air before switching the sand filter on and after every maintenance operation. Omitting this operation will greatly affect the lifespan of the product. NOTE: It is important to repeat this operation every time you start the pump after winterizing, any maintenance and backwashing the sand bed.
Page 14
GFCI INSTRUCTIONS The GFCI must be tested before each use. Do not use the pump if this test fails. For asistance, please visit the support section on our website, www.bestwayusa.com. RESET RESET RESET TEST TEST TEST USAGE INSTRUCTIONS CONTROL VALVE Press down on the control valve handle and rotate to desired function.
USAGE INSTRUCTIONS Rinse This function for initial startup, cleaning, and sand bed leveling after Backwash; water is pumped downwards through the sand bed, up through the Collector Hub and deposited out of the valve Port D. Filter This function is used to filter pool water and should be positioned here 99% of the time.
USAGE INSTRUCTIONS To avoid water leakage, screw the Port D Cap (P) onto the Control Valve Port D before operating the sand filter. When the control valve is set to the Backwash, Rinse, or Drain position, remove the Port D Cap (P), water will discharge from the Control Valve Port D.
Page 21
DISASSEMBLY & STORAGE INSTRUCTIONS DRAINING Draining: For draining, follow the illustrations. Drawings are for illustration purposes only. May not reflect actual product. Not to scale. Before draining your pool water, make sure that you are draining your pool away from the house and any objects that are subject to water damage.
DISASSEMBLY & STORAGE INSTRUCTIONS Storage: Remove all accessories; be sure that the sand filter, hoses and debris screens are completely clean and dry before storage. If all the parts are not completely dry, mold may result. Before storage, remove and dry the sand, and store in dry place. We strongly recommend disassembling the sand filter when the environment temperature is below 50ºF / 10ºC.
You will be required to submit proof of purchase from an authorized seller. This warranty does not cover Products purchased as used or “second hand as is”. Bestway reserves the right to request additional information in order to process a warranty claim, including, but not limited to, Product serial numbers or photos of the Product or parts.
Page 24
Please write the problem you are having with your specific product, be as detailed as possible: Note: MAIL-IN OPTION ONLY. This Mailing information: Bestway (USA), Inc. warranty form must be filled out with a Attn: Warranty copy of your receipt/invoice and mailed 3435 S.
Need help?
Do you have a question about the 58500E and is the answer not in the manual?
Questions and answers
Water is leaking right below valve where the 6 screws hold the top on. I removed & there is no seal...tightened it back up & still leaking.
To fix a water leak near the valve on a Bestway 58500E where the screws hold the top on, check the following:
- Ensure the control valve is not set between two functions. Set it to one function only.
- Inspect the gasket or O-ring near the valve area. If it is broken or out of place, replace or reposition it.
- Tighten any loose screws or hose connections near the valve.
- If leakage is from Port D, make sure the cap is installed and the gasket is in good condition. Replace the gasket if necessary.
These steps should help stop the leak.
This answer is automatically generated