Related Manuals for INHECO Ultraflat HT 2-TEC
Summary of Contents for INHECO Ultraflat HT 2-TEC
- Page 1 User and Installation Manual CPLC Ultraflat MTC Heating and Cooling Unit Part no.: 7100117 Doc ID: 900410-002 11/2024...
-
Page 2: Company Information
Technical Support & Trouble Shooting Instructions: inheco.com/tech-support.html INHECO Industrial Heating and Cooling GmbH reserves the right to modify their products for quality improvement. Please note that such modifications may not be documented in this manual. This manual and the information herein have been assembled with due diligence. -
Page 3: Table Of Contents
7 Maintenance ..................................23 7.1 Refilling ..................................23 7.2 Software updates ................................. 23 7.3 Calibration / verification............................... 23 8 Troubleshooting and support ............................24 8.1 Return device for repair .............................. 24 9 Accessories ..................................25 INHECO CLPC Ultrafralt MTC User Manual... -
Page 4: About This Manual
Broken seals on INHECO devices lead to the loss of warranty as well. INHECO will only accept parts / devices for return that do not pose a threat to the health of our staff. In particular, the devices may not have been used in Biosafety Level 3 and 4 environments or have been exposed to radioactive or radiation materials. -
Page 5: Abbreviations And Glossary
All devices cooled with the "Heat Exchanger Liquid cooling" MTC / STC devices Millimeter Multi TEC Control controls up to 6 INHECO devices individually Offset The difference between the set temperature and actual value once the temperature is stable Protective Earth PT100 PT100 is a Resistive-Temperature-Detector (RTD). -
Page 6: Safety Instructions
Biosafety Level Regulations of the WHO Laboratory Biosafety Manual. NOTICE Electromagnetic field The device is not designed for use in residential areas. Thus, there is no guarantee of adequate protection of radio reception in this area. INHECO CLPC Ultrafralt MTC User Manual... -
Page 7: Technical Alterations
8A. Technical alterations – Do not alter the product. Any modification or change not approved by INHECO leads to the loss of warranty and INHECO´s liability. – Use only original parts provided by INHECO. Parts provided by other suppliers can impair the functionality of the unit. -
Page 8: Danger Signs
INFORMATION This information symbol indicates useful notes that should be observed in order to work optimally with the product. Table 2: Information Symbols INHECO CLPC Ultrafralt MTC User Manual... -
Page 9: Product Description
In case of parcel or product damages, take photos of the damaged boxes and products and email these to techhotline@inheco.com immediately. Transportation damages must be reported to INHECO within 7 days of delivery. Illustration 2: Scope of delivery – CLPC (1) with Sub-D-Connector (2) -
Page 10: Functional Elements
New labels can be ordered at INHECO. In case the label is missing and you do not know the part number and serial number, they can also be read out with the software (MTC/STC Demo Tool) which can be downloaded from INHECO´... -
Page 11: Illustration 6 Label On Instrument
INHECO Product description | 3 Illustration 5: Example for shipment labels on the package Caution Hot Illustration 6: Label on instrument INHECO CLPC Ultrafralt MTC User Manual... -
Page 12: Technical Data
Table 4: Environmental Conditions *Condensate can prevent the CPLC from operating properly and can damage the CPLC. Condensate should be eliminated on a daily basis or more often, for example by heating cycles in between cooling cycles. INHECO CLPC Ultrafralt MTC User Manual... -
Page 13: Illustration 7 Dimensions Of The Cplc Ultraflat
INHECO Product description | 3 Dimensions Illustration 7: Dimensions of the CPLC Ultraflat (left) and 7100117 (right); top view dimensions are equal; values in mm. INHECO CLPC Ultrafralt MTC User Manual... -
Page 14: Installation
You can find a list of adapters for tubes, reservoirs or plates at www.inheco.com. For custom solutions, please contact sales@inheco.com. 4.1.3.1 Installation of PCR Adapter The mounting frame for PCR Adapter (sold separately, →... - Page 15 INHECO Installation | 4 Step 2: Remove the mounting frame Step 3: Place the PCR Adapter on the CLPC . Step 4: Place the mounting frame over the PCR Adapter. INHECO CLPC Ultrafralt MTC User Manual...
- Page 16 Step 5: Fasten the mounting frame with the mounting frame screws hand tight (0.25 Nm respectively) The PCR Adapter is installed. 4.1.3.2 Installation of Flat Bottom Adapter To mount the Flat Bottom Adapter: Step 1: Unscrew the mounting frame screws (1) and put aside. INHECO CLPC Ultrafralt MTC User Manual...
- Page 17 Installation | 4 Step 2: Remove the mounting frame Step 3: Attach the outer frame of the flat bottom adapter with 2 screws. Step 4: Attach the plate of the flat bottom adapter with one screw. INHECO CLPC Ultrafralt MTC User Manual...
- Page 18 Adapters other than PCR-Adapter and Flat Bottom Adapter do not need a Info frame. To install different adapters: The CPLC must be free of adapters. Step 1: Unscrew the mounting frame screws (1) and put aside. INHECO CLPC Ultrafralt MTC User Manual...
- Page 19 INHECO Installation | 4 Step 2: Remove the mounting frame Step 3: Screw in the adapter plate to the plate fixation hole INHECO CLPC Ultrafralt MTC User Manual...
-
Page 20: Mechanical Integration
– for CPLC Ultraflat 4 screws are necessary Illustration 8: Drilling Scheme for CPLC Ultraflat Contact INHECO for further information how to place the devices onto the working table to prevent damage from the device or/and to assure that the CPLCs are working with the given specifications. -
Page 21: Initial Operation
5 Initial Operation 5.1 Connecting devices to the MTC / STC In order to connect an INHECO heating / cooling / shaking device, the TEC Control Unit has to be equipped with the corresponding Slot Module. There are blue, black, and yellow Slot Modules available. -
Page 22: Operation
6.2 Operating the CPLC The device can be operated by a MTC/STC, by the INHECO Demo Tool software or by the software of your liquid handling workstation. -
Page 23: Maintenance
For proper performance of the CPLC devices, it is recommended to verify the thermal performance at least once a year. Depending on the application, shorter verification intervals may be required. INHECO recommends to use the INHECO Measurement Plate (IMP) to perform the verification. Please contact techhotline@inheco.com in case of performance deviations from set values. -
Page 24: Troubleshooting And Support
Exchange of parts or broken seals lead to the loss of warranty. Spare Parts must be ordered from INHECO. INHECO will only accept parts / devices for return that do not pose a threat to the health of our staff. In particular, the devices may not have been used in Biosafety Level 3 and 4 environments or have been exposed to radioactive or radiation materials. -
Page 25: Accessories
2400125 Teleshake 95, Thermoshake, Heated Lid with MTC/STC Blue Slot Module connects CPAC with MTC/STC 2400128 Thermal Adapter for Temperature Transfer All standard adapter can be downloaded from www.inheco.com or requested from sales@inheco.com. Miscellaneous Product name Description Part number INHECO... - Page 26 Illustration 6 Label on instrument ……………………………………………………………………. Illustration 7 Dimensions of the CPLC Ultraflat …………………………………………………… Illustration 8 Drilling Scheme for CPLC Ultraflat …………………………………………………… Illustration 9 Example of connected heating / cooling / shaking device ………………………… INHECO CLPC Ultrafralt MTC User Manual...
- Page 27 INHECO Table of tables Table of tables Table 1 Danger Signs ........................Table 2 Information Symbols ......................Table 3 Technical Data incl. Dimensions................... Table 4 Environmental Conditions ..................... INHECO CLPC Ultrafralt MTC User Manual...
Need help?
Do you have a question about the Ultraflat HT 2-TEC and is the answer not in the manual?
Questions and answers