Johannus LiVE 3P Quick Reference Manual

JOHANNUS LiVE 3P
Overview of controls:
A SET
B Capture memory locations (1-8)
C Tremulant (for each work)
D Pre-programmed memory locations
(PP to T and PL)
E RO: Reeds Off
F CR: Crescendo
G MB: Manual Bass
H CF: Cantus Firmus
I VOL.: General volume
J TRANS.: Transposer
K - and + pistons
L ENTER
M MENU
N 0: Cancel
The headphones connection is placed at the left hand side bottom of the keybed.
Options (under 'Manual II', point P):
- Standard model is without options (no pistons as point U, W).
- Premium model has option pistons for 'Solo voices' (point U).
- Platinum model has both option pistons for 'Orchestral voices' (point W) and 'Solo voices' (point U).
O Manual I
P Manual II
Q Manual III
R On/Off (mains power switch)
Headphones connection
S USB port
T Display
U Option: Solo voices*
V SEQ- and SEQ+ pistons
W Option: Orchestral voices*
X S/S: All Swells to Swell
Y Listening position
(Cons, Front, Center, Rear)
Z Sample banks
(Organ 1 to Organ 5)
Switch on:
On the right hand side bottom of the keybed, you will find the on/off mains power switch to turn on
the organ. Wait several seconds. The lights of the 0-piston and the as standard set functions light up.
The settings appear on the display.
Accessories:
Sequence - and + (SEQ- and SEQ+):
Sequence is a function to call up capture memory locations (1-8) in a sequential way.
All Swells to Swell (S/S):
All Swells to Swell transforms the swell pedal for Manual II to a swell pedal for the whole organ.
If no expression pedal is configured as a swell pedal for Manual II, the S/S piston cannot be activated.
Reeds Off (RO):
Reeds Off is a function to switch off all reeds simultaneously. The function is reversible.
Crescendo (CR):
Crescendo is a piston to activate the crescendo pedal.
If no expression pedal is configured as a crescendo pedal, the CR-piston cannot be activated.
Manual Bass (MB):
Couples the Pedal monophonic to Manual I.
Only the lowest key that is played on Manual I is coupled from the Pedal to Manual I.
Cantus Firmus (CF):
Couples Manual II monophonic to Manual I.
Only the highest key that is played on Manual I is coupled from Manual II to Manual I.
Transposer (TRANS.):
The Transposer function shifts the pitch by half-tone increments (from -8 to +8).
The transposer setting can be read on the display (Trans:..).
- Press the TRANS.-piston.
- Use the - and + pistons to set the pitch.
- When the transposer change needs to be saved, press the ENTER-piston while the TRANS.-piston is
illuminated.
Cancel function (0):
The 0-piston cancels stops in two ways:
1. A short press on the 0-piston: only the last change is cancelled.
2. A long press on the 0-piston: all stops are cancelled.
JOHANNUS MENU (MENU):
In the Johannus Menu several functions of the organ can be set:
- Press the MENU piston to activate the Johannus Menu on the display.
- Navigate the menu with the - and + pistons.
- Confirm a choice by pressing the ENTER-piston.
- Cancel or step back in the menu by pressing the MENU-piston.
PRE-PROGRAMMED MEMORY LOCATIONS (PP-T and PL)
Pre-programmed memory locations are available by operating pistons PP to T and PL. These seven
memory locations have factory settings (presets) appropriate for the quiet pianissimo to the loud tutti
and the classical plenum These memory locations are available per sample set.
Calling up a pre-programmed memory location:
- Press a pre-programmed memory location (PP-T or PL).
Quick Reference Guide