Table of Contents
Advertisement
Quick Links
Translated from German to English - www.onlinedoctranslator.com
Save This Manual for Future Reference
Original Instruction
Log Saw
Operator's Manual
MODEL NUMBER :
GAMUL W4
SERIAL NUMBER :
Both model number and serial number may be found on the main
label. You should record both of them in a safe place for future use.
FOR YOUR SAFETY
READ AND UNDERSTAND THE ENTIRE MANUAL BEFORE
OPERATING MACHINE
LUMAG GmbH
Rudolf-Diesel-Str. 1a, D-84375 Kirchdorf a.Inn
www.lumag-maschinen.de
Advertisement
Table of Contents
Related Manuals for Lumag GAMUL W4
Summary of Contents for Lumag GAMUL W4
- Page 1 Original Instruction Log Saw Operator's Manual MODEL NUMBER : GAMUL W4 SERIAL NUMBER : Both model number and serial number may be found on the main label. You should record both of them in a safe place for future use.
-
Page 2: Table Of Contents
Contents Supplied stored or transported under ambient Assembly temperatures between -25°C and 55°C. Know your Machine Speci cations Features & Controls operation Model Number GAMUL W4 Maintenance 230VAC 50Hz AC motor Storage 2200W S2 15min* Power P Wiring Diagram 1 kA... -
Page 3: Symbol
Electrical Requirements Conne ctt he ma inleadstoaster nda rd 230V ± Wear safety footwear. (50Hz 1Hz) electrical supply which has protection ± devices of under-voltage, overvoltage, over- current as well as aresidual current device (RCD) which maximum residual current rated at 0.03A. Wear safe clothing. -
Page 4: Safety
condition. SAFETY Dress Properly Do not wear loose clothing, gloves, neckties or Understand Your Log Saw jewelry (rings, wrist watches). They can be Read and understand the owner's manual caught in moving parts. Electrically protectively and labels a xed to the log saw. Learn its non-conductive gloves and non-skid footwear application and limitations as well as the are recommended when worn. - Page 5 Keep Bystanders Away into the saw blade. Never plie logs to be split in a manner that will cause you to reach across the Allow only one person to load and operate the log saw. Only use your hands to operate the log saw.
-
Page 6: Contents Supplied
CONTENTS SUPPLIED The log saw comes partially assembled and is shipped in carefully packed carton. After all the parts have been removed from the carton, you should have: (× 2) 8. Saw Blade Guard 1 1st engine 2. Base Frame 9. -
Page 7: Assembly
Put the saw blade guard 1 against inner side of 15. Back Plate 1 the same connecting part, align the holes and 16. Back Plate 2 bolt the saw blade guard 1, connecting part and 17. Guide Pipe with Return Spring ×20 back plate 1 together with three M8 bolts, 18. - Page 8 handle lock nut as Fig. D. Attach the handle to the back of the log carriage. ×25 bolts and lock nuts as Secure it with two M8 ×20 into the hole Fig. B. Screw the wing bolt M5 at the upper right corner. ×...
- Page 9 Inner Saw Blade Cover Slide the shaft through the center hole of the inner saw blade cover and align its other holes with those on the motor plate as Fig. F. Secure it with three M8 ×20 bolts, washers and lock nuts on the upper side ×...
- Page 10 Limit Plate Fixing Return Spring and Chain Mount the limit plate and fasten with two M5× Take the cotter pin and washer from the guiding 10 screws and washers as Fig. J. pipe with spring as Fig. I, step 1. Push the log carriage to the base frame until the open end of the guiding pipe is inserted into the angle part at the base frame as Fig.
-
Page 11: Know Your Machine
Log Carriage Extension ×20onthebacksideof LoosenthewingboltM5 the log carriage until the log carriage extension can be inserted into the opening. Slide the log carriage extension into the channel and align it correctly. Then tighten it with the wing bolt. × KNOW YOUR MACHINE Features and Controls Saw Blade Cover Guard Plate... -
Page 12: Operation
operation guard will open and show the saw blade. Keep pushing with even strength until the log on the logcarriageiscut.Stoppushingandlogcarriage will Stake on Level Ground retract to its original position. Move the rest of log to the cutting position and continue next To secure your log saw, use four bolts or stakes cycle until the work is accomplished. -
Page 13: Maintenance
3. Pull the cotter pin and washer from the MAINTENANCE return guiding pipe. 4. Remove the M8×50 bolt, washers and nut Warning! Prior to any adjustment, xing the chain. maintenance or service work disconnect the mains power plug! × Cotter Pin General Maintenance Measures Keep all safety devices, air vents and the engine housing free of dirt and dust as far as... -
Page 14: Storage
6. Remove the fourM5 ×10 screws and washers STORAGE from the saw blade guard and also the outer saw blade cover. Store unused equipment in a dry, locked place out of the reach of children. Before a longer period of storage carry out the following to extend the saw service life and ensure an easy operating. -
Page 15: Wiring Diagram
WIRING DIAGRAM TROUBLE SHOOTING cause problem Remedy Saw blade gets Fastening nut tightened insu - Tight fastening nut right-hand loose after turning thread ciently o the motor 1. Failure mains fuse 1. Check mains fuse 2. Extension cable defect 2. Exchange extension cable Motor does not 3. -
Page 16: Parts Schedule
PARTS SCHEDULE LOG SAW... -
Page 17: Parts List
Parts List Q'ty Q'ty Description Description Screw M5×12 Washer 8 Washer 5 Locknut M8 Flat Washer 5 Saw Blade Guard 2 Bolt M8×55 Inner Saw Blade Cover Outer Saw Blade Cover Flat Washer 16 Switch Return Spring Bolt M8×70 Motor Rear Saw Blade Flange Base Frame 2 Saw Blade... - Page 18 Subject to change without notice! Version GAMULW4 (05.2024 en) LUMAG dealer can be found at www.lumag-maschinen.de LUMAG GmbH Rudolf-Diesel-Str. 1a D-84375 Kirchdorf a.Inn Germany Internet: www.lumag-maschinen.de...
Need help?
Do you have a question about the GAMUL W4 and is the answer not in the manual?
Questions and answers