Subscribe to Our Youtube Channel
Related Manuals for Lumag WS600
Summary of Contents for Lumag WS600
- Page 1 Manual For Log Saw WS600 230V/50HZ For Your Safety Read And Understand The Entire Manual Before Operating Machine. Save This Manual For Future Reference...
-
Page 2: Proper Use
1. Proper use The firewood drag saw is designed for cross-cutting firewood within the specified dimensions (see technical data) in a feed cradle that pivots towards the saw blade. This tool is only designed for outdoors use and for operation by one person. Other persons must remain a safe distance away from the tool whilst it is operating. - Page 3 •Concentrate on what you are doing. Use common sense when working. Do not operate the tool if your mind is not on your work. •Never use an electric tool with a switch that cannot be turned on and off. •Warning! The use of other tools and accessories may put you at risk of injury. •Always pull the plug out of the power socket before adjusting or servicing the machine.
- Page 4 •If the table insert is worn, replace it. •Always stand to the side of the saw blade when working with the saw. •Never load the machine so much that it cuts out. •Make sure that off-cuts do not catch on the saw blade crown. Risk of catapulting! •Never remove loose splinters, chips or jammed pieces of wood when the saw blade is running.
-
Page 5: Technical Data
•Only use sharp saw blades. Important: Risk of injury! Never reach into the running saw blade. Wear goggles Wear ear-muffs Wear a breathing mask 3. Technical data Model: W S 60 0: Motor: 23 0V ~ 50Hz Power : 35 00 W Protection type: IP 54 Idle speed n 。... -
Page 6: Assembly Procedures
4.Assembly procedures: Step No.1 Assembly for motor-supporting legs and supporting legs with switch plate (See Figure 1,2,3,4) Figure 1... - Page 7 Part #1 Figure 2( Figure 3 hole D and bended edge of part_14A Figure 4 1）Connect motor-suporting legs (Part #1) to the steel-supporting legs with switch-holding plate(Part #14) by using the two plates(Part#13) on left & right side each.Then fix Part#1&Part#14 by putting the bolts M8X55(Part#28)&nuts M8X55&washer into the holes of Part#13&Hole C.
- Page 8 14,15,15A,16,17,18,18A,18B) Figure 8 Figure 10 Figure 9 1) Firstly put the movable inner blade cover assembly(Part#24)towards the upper open space between Leg C & Leg E (See Figure 12,13,14) Figure 11...
- Page 9 Figure 11A Figure 12（put part_43 into Hole E） Part 24 Figure 13 Figure 14 (part #44 & Hole H Figure 15 (hole H & part 45) Figure 15A Figure 16 Alignment of Hole H Figure 17 (part 8 & hole G) Figure 18...
- Page 10 Konb for extension support Knob for scale ruler Figure 19A Figurer 19B 2)Fix inner blade cover (Part #24) and rocker table (Part#18) by putting 4pcs M6X40 inner hexagon bolts(Part#43)&washers into 4 holes(Hole E) of Leg C and holes(Hole2)of the support plate(Part#) for Part#24.（See Figure 9,10,,11,11A, 12,13）...
- Page 11 Figure 20 Figure 21 1) Firstly connect the outer blade cover(Part#22)to Leg B by putting the two nuts M10(Part #47) on Leg B to Hole of blade cover angle-plate(Part#50A),(Just put the two bolts into hole, don’t screw the two M10 nuts)(See Figure 22,23,23A, 23B,23C)
- Page 12 Figure 22 Figure 23 Just put two bolt into hole 1 without screwing. Figure 23A Figure 23B (Connection of Hole1&47# Screw) Hole K of cover Bracket Figure 23C Figure 24 2) Secondly connect the outer blade cover (Part#22)to Leg A by inner hexagon bolt M6X50(Part#48)&Nut M6 through Hole K of Cover Bracket and tighten the bolt.(See Figure 23C) 3) Thirdly tighten the two M10 nuts (Part #49) as shown in Figure 24.
- Page 13 1） Lift the well-assembled rocker table with movable inner blade cover and make the three supporting legs(Leg C/D/E)of rocker table nestle inside the Hole M of the three slot(Part#1A),then fix them by putting through 3 bolts &nuts M16X55(Part #53&54) (See Figure 25,27,27A,27B,27C,) Figure 26 Figure 26A Figure 26B...
- Page 14 Figure 27 Figure28 Figure28A Figure 28B Step 7.Assembly of Guiding Pipe Lift &push the Rocker table forwards, and push the return spring guiding pipe(Part#5),towards the hole of spring seat and then put washer into the guide bar and put the pin into the hole of guiding pipe for locking. (See Figure 29,29A, as above) Part #12 Spring seat...
- Page 15 Figure 29 Figure 29A Part #6 Return Spring Adjust the position so that the blade(Part#7)is in central cutting line and the movable inner blade cover(Part#24) does not touch either the left-side outer blade cover or the right-side outer blade cover(Part#32&32A&33) The same as other side.
- Page 16 Figure 33 Moviing handle Step 10.transport Figure 34 The moving handle is for transport.(See fig 34)
-
Page 17: Before Starting The Machine
6. Before starting the machine •Do not start the machine until you have made yourself familiar with these operating instructions and all the safety instructions. If you have no experience in handling these machines, you should obtain assistance from an experienced person. •Unpack the saw and check it for damage which may have occurred in transit. -
Page 18: Changing The Saw Blade
cut ).To do this return the feed carriage to its initial position, turn the wood along the cut and saw through it again. •Important: If the saw blade does not reach a standstill after a maximum of 10 seconds, have the switch checked by an authorized electrician and replaced if necessary. •Pull the power plug immediately after finishing work. - Page 20 Name motor support legs motor axle wheel guide pipe return spring blade protection plate safety cover switch table extension spring seat Connecting plate for leg switch holding plate inner flange outer flange Table hook rocker table limit ruler axle for return spring plastic pad outer blade cover inner blade cover...
Need help?
Do you have a question about the WS600 and is the answer not in the manual?
Questions and answers