Datalogic Heron D130 Manual
  1. Manuals
  2. Brands
  3. Datalogic Manuals
  4. Barcode Reader
  5. Heron D130
  6. Manual
Datalogic Heron D130 Manual

Datalogic Heron D130 Manual

Hide thumbs Also See for Heron D130:
Table of Contents

Advertisement

Quick Links

Download this manual
Use of Heron™ D130
Reader

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Heron D130 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Datalogic Heron D130

Summary of Contents for Datalogic Heron D130

  • Page 1 Use of Heron™ D130 Reader...
  • Page 2 © IZUM, 2024 IZUM, COBISS, COMARC, COBIB, COLIB, CONOR, SICRIS, E-CRIS, COBISS3, mCOBISS, COBISS+, dCOBISS, COBISS4, SGC, COBISS Lib, COBISS Cat, COBISS Ela are registered trademarks owned by IZUM.

  • Page 3: Table Of Contents

    Figure 5: Heron D130 reading zones ..................2 TABLES Table 1: Heron D130 reader setup ....................3 Table 2: Additional settings for barcode type Interleaved 2 of 5 ............ 4 Table 3: Adding Enter key ......................5 Table 4: WEDGE setup ........................5 Table 5: Test barcodes ........................

  • Page 5: Introduction

    Use of Heron™ D130 Reader Introduction The document lists the required configuration and describes how to install the barcode reader to be used within the COBISS system. Use of HERON™ D130 reader The HERON™ D130 reader can be installed in the COBISS system as a keyboard extension. If you connect it to the VT510 terminal or to a PC, use the enclosed Wedge cable (Figure 1).

  • Page 6: Figure 5: Heron Tm D130 Reading Zones

    Use of Heron™ D130 Reader TECHNICAL DATA AND READING DIAGRAM Figure 4 shows the reader's technical data, while Figure 5 shows the reader's reading zones. Figure 4: Technical data Figure 5: Heron D130 reading zones © IZUM, 9. 10. 2024, VOS-NA-EN-377, V0.14...

  • Page 7: Setting Up The Heron™ D130 Reader For Usb

    If you make a mistake, start the procedure from the beginning. The settings are for a USB cable. Table 1: Heron D130 reader setup 1. Before you start the procedure, restore the reader factory settings (RESTORE DEFAULT).

  • Page 8: Additional Settings For Type Interleaved 2 Of 5

    Use of Heron™ D130 Reader Additional settings for type Interleaved 2 of 5 Set up the reader when it is connected (see recommendations in chapter 3 (Setting up the Heron™ D130 reader)). Use this setup if you want settings for scanning the code Interleaved 2 of 5 (ITF) for odd digit lengths.

  • Page 9: Setting Up Additional Enter Key

    Use of Heron™ D130 Reader Setting up additional Enter key If necessary, add the activation of the Enter key along with the scanned barcode to the setting. Table 3: Adding Enter key Enter configuration mode (Enter Configuration). Add barcode for Enter key. Finish the procedure and save the set-up parameters (Exit and Save Configuration).

  • Page 10: Testing Correctly Set-Up Parameters

    Use of Heron™ D130 Reader Testing correctly set-up parameters To check if the parameters have been set up correctly, use the test barcodes in Table 5. Table 5: Test barcodes COBISS Other barcodes CODE 93 During the test, the reader will scan all barcodes. If the library uses the barcode type Interleaved 2 of 5 with an odd number of digits in the barcode, also carry out the steps from Table 3.

Table of Contents