Troubleshooting Guide; Specifications; Maintenance - Emerson EWV403 Owner's Manual

TROUBLESHOOTING GUIDE

If you have followed the instructions contained in this manual and have difficulty in operating your VCR, locate the PROBLEM in the
left column below. Check the corresponding CORRECTIVE ACTION column to remedy the problem.
PROBLEM
No power.
Timer recording is impossible. • Make sure the timer recording is set correctly.
Cannot go into Record mode.
Playback picture is partially noisy. • Adjust tracking control for a better picture by pressing [CHANNEL
Cannot view a tape but the
audio is OK .
No or poor playback picture.
TV programs cannot be seen
normally.
No VCR operation from the
infrared Remote Control.
Video or color fades in and out • You cannot copy a copyrighted video tape. You are experiencing copy guard protection.
when making a copy of a video tape.

SPECIFICATIONS

Operating temperature :
Converter output :
Power requirement :
Power consumption :
Supplied Accessories
Remote control
(NA312UD/NA362UD)
• Designs and specifications are subject to change without notice and legal obligation.
• If there is a discrepancy between languages, the default language will be English.

MAINTENANCE

Servicing
Should your VCR become inoperative, do not try to correct
the problem by yourself. There are no user-serviceable parts
inside. Turn off, unplug the power plug, and please call our
help line at
1-800-256-2487,
to locate an Authorized Service Center.
Cabinet Cleaning
• Wipe the front panel and other exterior surfaces of the VCR
with a soft cloth immersed in lukewarm water and wrung dry.
• Never use a solvent or alcohol. Do not spray insecticide liq-
uid near the VCR. Such chemicals may cause damage and
discoloration to the exposed surfaces.
• Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
• Make sure the power is off.
• Make sure the VCR clock is set correctly.
• Make sure the tape has a safety tab. If needed, cover the hole with cellophane tape.
• Head cleaning may be necessary. Refer to "AUTO HEAD CLEANING" .
• Make sure the VCR is not in the Menu mode.
• Turn on the TV and set the TV to channel 3. If channel 3 is already occupied for broad-
casting, change the RF output to CH 4, and change the TV channel to CH4.
(See "RF Output Channel" on page 3 for the detail.)
• Fine tune your TV.
• Re-check the ANT. IN and ANT. OUT connections. See page 3.
• Press [VCR/TV] on the remote control so that the VCR/TV indicator on the VCR disap-
pears.
• Make sure the power plug is connected to an AC outlet.
• Check batteries in remote control.
41°F~104°F (5°C~40°C )
VHF Channel 3 or 4.
120V, 60Hz
14 Watts
CORRECTIVE ACTION
Dimensions :
Weight :
Two AA batteries
Auto Head Cleaning
• Automatically cleans video heads as you insert or remove a
cassette, so you can see a clear picture.
• Playback picture may become blurred or interrupted while
the TV program reception is clear. Dirt accumulated on the
video heads after long periods of use, or the usage of rental
or worn tapes can cause this problem. If a streaky or snowy
picture appears during playback, the video heads in your
VCR may need to be cleaned.
1. Please visit your local Audio/Video store and purchase a
good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the problem,
please call our help line at 1-800-256-2487, to locate an
Authorized Service Center.
NOTES:
• Remember to read the instructions included with the video
head cleaner before use.
• Clean video heads only when problems occur.
– 7 –
] on the VCR.
( )
W 14-1/4" (360mm)
H 3-5/8" (92mm)
D 8-1/2" (216mm)
4.0 lbs. (1.8 Kg.) (approx.)
RF Cable
EN