Emerson EWV403 Owner's Manual

Emerson EWV403 Owner's Manual

Emerson owners manual vcr ewv403
Hide thumbs Also See for EWV403:

Advertisement

Owner's Manual
Video Cassette Recorder
EWV403

1. Before using your VCR

Basic VCR/TV Connection
Antenna
Cable
Cable
Signal
Signal
or
(Back of TV)
Disconnect
4
Plug the AC power cords of the VCR and TV into the AC outlets.
Hint for Cable Box or Satellite Box
Connection A
(Back of VCR)
(Cable box or
ANT
Satellite box)
IN
IN
OUT
OUT
RF Cable
Cable
(supplied)
Signal
(Back of TV)
Select this connection when you want to view or record a
scrambled channel. With this connection, channels cannot
be changed on the VCR. You can view or record ONLY the
channels you have selected on the cable box or the satellite
box.
• While you are recording, only the recorded channel can
be viewed.
To select channels of the cable box or satellite box
1)Turn on the VCR by pressing the POWER button, and
then, press the VCR/TV button.The POWER and the
VCR/TV indicators on the front panel will light on. Then,
press the CHANNEL buttons to select channel 3 or 4
(the same channel as the output channel of the cable
box or satellite box).
• If you use the channel 4, you need to change the VCR's
RF output to channel 4. Refer to "RF Output Channel".
2) At the TV, select channel 3 or 4 (the same channel as
you have selected at step 1).
3) At the cable box or satellite box, select the channel you
want to view or record.
EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS
OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A.
If you need additional operating assistance after
reading this owner's manual or to order replace-
ment accessories, please call
TOLL FREE : 1-800-256-2487
or visit our web site at http://www.funai-corp.com
Antenna
(Back of VCR)
or
ANT
2
IN
3
Connect
OUT
Connect
RF Cable
(supplied)
Connection B
(Back of VCR)
ANT
(Cable box or
IN
Satellite box)
Cable
OUT
E
Signal
IN
OUT
RF Cable
(supplied)
Select this connection when you want to change channels
on the VCR. With this connection, you may watch one
channel while recording another.
• You may not view or record a scrambled channel.
To select channels of the cable box or satellite box
1)At the cable box or satellite box, select channel 3 or 4
(the same channel as the VCR's RF output channel.)
• Refer to "RF Output Channel".
2)At the TV, select the same channel as the output chan-
nel (3 or 4) of the cable box or satellite box.
3)Turn on the VCR by pressing the POWER button, and
then, press the VCR/TV button .The POWER and
VCR/TV indicators on the front panel will light on. Then,
select the channel you want to view or record.
To play back a tape
Follow the steps 1) to 2) above. Then, play back a tape.
• Refer to "Playback" on page 5.
To view one channel while recording another
1)While you are recording on the VCR, press the VCR/TV but-
ton so that the VCR/TV indicator disappears on the VCR.
2)At the cable box or satellite box, select the channel you
want to view.
RF Output Channel
If channel 3 is already occupied for broadcasting,
1) Set your TV to channel 4.
2) Insert a pre-recorded tape into the VCR.
3) Press the PLAY button once.
4) After a few seconds, press the PLAY button on the VCR for 3 seconds.
• The RF output channel will change to channel 4 from channel 3 and you will
see a playback picture.
• When a picture does not appear on the TV screen, repeat step [4].
5) Press the STOP button to stop playback.
Stereo TV Connection
You can use the AUDIO OUT jack and
VIDEO OUT jack on the back of the
VCR if your TV has Audio/Video Input
(Back of TV)
jacks. In this case, you need to set the
TV to external Line Input Mode. Please
refer to your TV's owner's manual.
Front & Rear Terminals
AUDIO OUT jack
Connect the audio cable to the audio in jack
of a camcorder, another VCR, a stereo
amplifier, or an audio system.
E
(Back of TV)
RF Cable
VIDEO OUT jack
Connect the video cable to the video in jack
of a camcorder, another VCR, or a TV.
VIDEO
AUDIO
POWER
CHANNEL
Supplied Accessory
• Remote control
• RF Cable
(NA372UD) with
(WPZ0901TM002)
Two AA batteries
- 1 -
VIDEO
AUDIO OUT
OUT
L
R
(Back of TV)
AUDIO IN jack
Connect the audio cable from the audio out
jack of a camcorder, another VCR, or an
audio source.
ANT
ANT IN jack
IN
Connect your antenna or cable box.
ANT
IN
AUDIO
AUDIO
ANT OUT jack
OUT
IN
OUT
OUT
IN
OUT
Connect the RF cable (supplied) to
VIDEO
the antenna input jack on your TV.
VIDEO
VIDEO IN jack
Connect the video cable from the video out
jack of a camcorder, another VCR, or an
audio-visual source (laser disc player,
POWER
REC
VCR/TV
TAPE IN
TIMER
video disc player, etc.).
MENU
Installing the Batteries for
the Remote Control
• Owner's Manual
Install two AA batteries
(0VMN03903)
(supplied) matching the
polarity indicated on
the bottom of the
remote control.
0VMN03903 / HF330UD
Hint
Hint
• The RF output channel may
not change when you adjust
tracking during playback. In
this case, stop the playback,
and start the playback again.
After that, press the PLAY but-
ton on the VCR for 3 seconds
again.
VIDEO
AUDIO IN
IN
L
R
ANT
IN
AUDIO
OUT
IN
OUT
VIDEO
Audio/Video Cables
(not supplied)
ANT
IN
1
OUT
Connect
(Back of VCR)
Printed in China
★★★★★

Advertisement

Table of Contents
loading

Summary of Contents for Emerson EWV403

  • Page 1: Before Using Your Vcr

    3) Press the PLAY button once. 4) After a few seconds, press the PLAY button on the VCR for 3 seconds. • The RF output channel will change to channel 4 from channel 3 and you will see a playback picture.
  • Page 2: Important Safeguards

    2. Important Safeguards TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, WARNING: DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC CAUTION SHOCK, DO NOT REMOVE COVER (OR BACK). RISK OF ELECTRIC SHOCK NO USER SERVICEABLE PARTS INSIDE.
  • Page 3: Preset For Use

    To Change the On-Screen Language 1) Press the MENU button until the main Do you connect the cable of the cable box or the satellite box to the VCR’s ANT IN jack? menu appears. 2) Select "LANGUAGE SELECT" by pressing the PLAY or STOP button.
  • Page 4: Troubleshooting Guide

    TV programs cannot be seen nor- • Re-check the ANT. IN and ANT. OUT connections. See page 1. mally. • Press the VCR/TV button on the remote control so that the VCR/TV indicator on the VCR disappears. No VCR operation from the •...
  • Page 5: Other Operations

    EJECT STOP EJECT • If you have connected the VCR to a cable box or satellite box, refer to “Hint for Cable Box or Satellite Box” section on page 1. To cue or review picture during play- back (Picture Search) POWER Press the F.FWD or REW button.
  • Page 6: Recording Features

    VCR power will be turned off. The TIMER indicator will flash. • If a tape is not in the VCR or does not have the record tab, the TIMER indicator flashes and timer recording cannot be performed. Please insert a recordable tape.
  • Page 7: Special Features

    • These functions are not available during recording. • Press the STOP button to stop the search. • If the end of the tape is reached during a Search, the VCR will cancel the search and rewind the tape. Auto Repeat You can repeat playback of a whole tape automatically.
  • Page 8: Limited Warranty

    This EMERSON Limited warranty applies only product, telephone or write to the following: to product purchased and used in the United States.

This manual is also suitable for:

Ewv403a

Table of Contents