Special Features - Emerson EWV403 Owner's Manual

Hints for Timer Recording
• If there is a power failure or the VCR is unplugged for more
than 30 seconds, the clock setting and all timer settings will be
lost.
• If the tape runs out before the end time, the VCR will switch to
the Stop mode immediately, eject the tape and the VCR power
will be turned off. The TIMER indicator will flash.
• If a tape is not in the VCR or does not have the safety tab, the
TIMER indicator flashes and timer recording cannot be per-
formed. Please insert a recordable tape.
To Stop an Automatic Timer Program already started
Press [STOP/EJECT] on the VCR.
To Check, Correct, or Cancel an Automatic Timer Program
1 Turn the power on by pressing [POWER].
2 Select main menu by pressing [MENU].
3 Select "TIMER PROGRAMMING" by pressing [PLAY] or
[STOP]. Then, press [F.FWD].
4 Select the program number which you want to check
by pressing [PLAY] or [STOP]. The details of the selected
program appears on the TV screen.
• Go to the digit you want to change by pressing [F.FWD] or
[REW]. Then, enter correct numbers by pressing [PLAY] or
[STOP].
• You may cancel the entire program by pressing [REW] dur-
ing the program number flashes.
Press [C.RESET/EXIT] to exit.
5
6 Press [POWER] to return to timer stand-by mode.

SPECIAL FEATURES

Copying a Video Tape
You can make copies of video tapes made by friends or relatives
for your enjoyment.
Warning: Unauthorized recordings of copyrighted video tapes
may be an infringement of copyright laws.
Connect the recording VCR(this unit), the playing VCR (another
source) and your TV using the following diagram.
Audio/Video cables
[Recording VCR]
(not supplied)
OUT
OUT
IN IN
AUDIO VIDEO
[Playing VCR]
(another source)
1 Insert a pre-recorded tape into the playing VCR.
2 Insert a tape with its safety tab into the recording
VCR.
3 Press [SPEED] on the remote control of the recording
VCR to select the desired recording speed (SP/SLP).
4 Select the "L1" or "L2"position on the recording VCR.
See page 3, under "Using AUDIO/VIDEO Input Jacks".
5 Press [REC/OTR] on the recording VCR.
6 Begin playback of the tape in the playing VCR.
(Use for monitoring)
(this unit)
ANT
RF cable
IN
(supplied)
AUDIO
OUT IN
OUT ANT in
VIDEO
• For best results during dubbing, use the VCR's front panel
controls whenever possible. The remote control might affect
the playing VCR's operation.
• Always use video-quality shielded cables with RCA-type con-
nectors. Standard audio cables are not recommended.
• You can use a video disc player, satellite receiver, or other
audio/video component with A/V outputs in place of the play-
ing VCR.
To Monitor the Recording
1 Turn on the TV and set the TV to channel 3. If channel 3
is already occupied for broadcasting, change the RF output
to CH 4, and change the TV channel to CH4.
(See "RF Output Channel" on page 3 for the detail.)
2 Press [VCR/TV] on the remote control of the recording
VCR so that the VCR/TV indicator comes on.
Auto Rewind
When a tape has reached the end during recording, playback,
or fast-forward, the tape will automatically rewind to the begin-
ning. After rewinding finishes, the VCR will eject the tape and
turn itself to off.
• The VCR will not rewind the tape automatically during timer
recording or One Touch Recording.
Real Time Tape Counter
• This shows the elapsed recording or playback time in hours,
minutes, and seconds. (The displayed time will not change dur-
ing blank portions on the tape.)
• The indication will appear when the tape is rewound further
than "0:00:00" on the tape counter.
[TV set]
– 6 – EN