Download Print this page

KStar WIFI PLUG Quick Use Manual

Photovoltaic inverter

Advertisement

Quick Links

photovoltaic inverter
FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved by the part
responsible for compliance could void the user's authority to operate the equipment.
FCC Radiation Exposure Statement
This equipment complied with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
KSTAR
- WIFI PLUG
Quick Use manual

Advertisement

loading
Need help?

Need help?

Do you have a question about the WIFI PLUG and is the answer not in the manual?

Questions and answers

Summary of Contents for KStar WIFI PLUG

  • Page 1 KSTAR photovoltaic inverter - WIFI PLUG Quick Use manual FCC COMPLIANCE STATEMENT: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • Page 2: Product Installation

    三.WIFI PIUG network Settings After the WIFI PLUG is plugged into the inverter, The COM Indicator light flashes for setting 1 To prepare an Android or iPhone that can be connected to the wireless network, the wifi configuration needs to first download the "ksolar 3.0"...
  • Page 3 Click "AP Device "to enter the WIFI connection page, select the WIFI name beginning with 11026 to connect it, and enter the password for the first connection, the password is 123456789; Return to the configuration page after successful connection. As shown in the figure below After connecting the WIFI at the beginning of 11026, click "Select"...
  • Page 4 After setting successfully, click "Refresh" at STA; If the collector is connected to the user's WIFI, you will see that the status is COMPLETED and the IP address for surfing the Net has been obtained. In the case of SCANNING, it means the collector is not connected to the user's WIFI. Check whether the user's WIFI password is entered correctly Registration and login 四....
  • Page 5 4.2 APP register * Android and Apple users register and log in the same operation, take android users as an example. register 4.2.1 Open the APP, click "Create account" to register "Enterprise Account " or "Personal Account " as required, and fill in the registration information as prompted (be sure to fill in the real information);...
  • Page 6 2. After adding the power station, click the power station to enter, and then click "+" in the upper right corner to add the collector. Enter the collector SN manually or by scanning the code. The name of the collector is defined by itself, such as "Inverter No. 1" 3.When the enterprise account is logged in for the first time to add a power station, it is necessary to select an affiliated user, which is a personal account.
  • Page 7 4.3 Log on to the website to register Open Google or firefox on your computer and enter the url: 119.28.137.157 as shown in the figure below 4.3.1 Click "Register " to register the enterprise account or personal account according to the needs (if you have already registered through APP, log in directly with the account), and fill in the information one by one when registering.
  • Page 8 4.3.2 After the addition operation is completed, click the added power station to enter the power station and check the power generation status of each equipment in the power station. You can also click a collector under the power station to view the details of the power generation of the individual equipment. As shown in the figure below...
  • Page 9 4.4 Enterprise account login 1. Corporate account much more than individual account set permissions management, business account to manage the end user, you can add the end user (personal account), enterprise bank account operation of the terminal can be assigned to the owner, the owner can log in the account to check the power generation equipment, and other equipment has no right to view the account;...