Related Manuals for Moxa Technologies VPort 07-3 Series
Summary of Contents for Moxa Technologies VPort 07-3 Series
- Page 1 VPort 07-3 Series Quick Installation Guide Moxa IP Camera Version 1.0, November 2024 Technical Support Contact Information www.moxa.com/support 2024 Moxa Inc. All rights reserved. P/N: 1802000070010 *1802000070010*...
-
Page 2: Ordering Information
Overview The VPort 07-3 Series is a compact IP dome camera that supports a maximum 2048 x 1536 video image at 20 frames per second or 1920 x 1080 video at 30 frames per second, and H.265/H.264/MJPEG. It is designed for mobile video surveillance applications and features EN 50155 compliance, vandal-proofing (EN 62262 IK8), operating temperature of -40 to 55°C or -40 to 70°C (T model), rugged M12... -
Page 3: Product Description
Sticker for camera mounting positions Contents of the Package • Quick installation guide (printed) • Warranty card NOTE Check the model name on the VPort’s side label to determine if it is the correct one for your order. NOTE This product must be installed in compliance with your local laws and regulations. - Page 4 All Models 4-pin D-coded female M12 • Ethernet connector: Can be used for both the PoE power supply (PoE model) and Auto MDI/MDI-X Ethernet connection NOTE To connect the VPort 07/P07-3MP Series to a network, use an Ethernet cable with D-code M12 connector and an M12 PoE switch or RJ45 PoE switch.
- Page 5 Solid metal top cover: This top cover can be removed for • adjusting the camera lens position. Transparent dome cover: The VPort 07-3 Series is designed with • a transparent PC dome cover, which is vandal-proof and satisfies EN 62262 (IEC 62262) Class IK8 requirements.
-
Page 6: Hardware Installation
Mounting screw holes: There are 4 mounting screw holes for • mounting the VPort 07/P07-3 Series on the ceiling or the accessory. • Screw for fixing the lens’s position: To adjust the position of the lens, loosen the thumb screw, and then retighten it after you are done with adjusting the position of the lens. - Page 7 To mount the camera on the ceiling, drill a hole through the gray portion of the sticker and then mount the camera with the 4 nut/gasket/spring-washer sets and the 4 indented hexagonal head tapping screws. NOTE The 4 screws for mounting the VPort 07-3 or the fixed plate are M4 type with a 30 mm length thread.
- Page 8 NOTE The 4 screws for mounting the VPort 07-3 onto the VP-SCO2 are M4 type with a 12 mm length thread. c. Mounting with the fixed plate If you cannot use the VP-FP2 nut/gasket/spring-washer set to mount the camera on your ceiling, use the VP-FP2 fixed plate.
- Page 9 NOTE The 2 screws for mounting the VP-FP2 onto a ceiling are M4 type with a 16 mm length thread. Step 3: Connect the camera with the 4-pin M12 D-code Ethernet connector and DB9 / 5-pin M12 connector. NOTE Connectors used with the cameras should be IP66 compliant. Step 4: Loosen the screw for adjusting the horizontal, vertical, and rotating lens position.
- Page 10 NOTE 1. If required, a dry pack (VP-DP03) can be ordered separately to absorb moisture from the inside of the camera. Remove the dry pack from the package. Use the sticker on the dry pack to attach it to the inside of the top cover to absorb any moisture that has entered the camera housing during installation.
-
Page 11: Software Installation
VPort’s web-based manager (web server). Non DHCP Server Network Environment If your VPort 07-3 Series is connected to a network that does not have a DHCP server, then you will need to configure the IP address manually. The default IP address of the VPort 07-3 Series is 192.168.127.100 and the default subnet mask is 255.255.255.0. - Page 12 VPort is restarted. Step 2: Access the VPort 07-3 Series’ web-based manager. Type the VPort 07-3 IP address in the web browser’s address field and press Enter. NOTE If the ActiveX control component for Microsoft Internet Explorer is necessary, enable IE Mode in Microsoft Edge and reload the VPort’s web interface while in IE Mode.
- Page 13 Step 4: Access the homepage of VPort 07-3 Series' web-based manager. After logging in successfully, the homepage of the VPort 07-3 Series’ web-based manager will appear. Check the following items to make sure the system was installed properly: 1.
-
Page 14: Wiring Requirements
Wiring Requirements ATTENTION Safety First! Be sure to disconnect the power cord before installing and/or wiring your Moxa VPort 06/P07-3 Series. Calculate the maximum possible current in each power wire and common wire. Observe all electrical codes dictating the maximum current allowable for each wire size. -
Page 15: Specifications
Top View Camera with SCO2 adaptor Specifications Input Current VPort 07-3 Series: 0.59 A @ 12 VDC, 0.27 A @ 24 VDC VPort P07-3 Series: 0.137 A @ 48 VDC Operating Standard Models: -40 to 55°C (-40 to 131°F) Temperature Wide Temp.
Need help?
Do you have a question about the VPort 07-3 Series and is the answer not in the manual?
Questions and answers