Page 1
Colours may vary Electric Scooter - XCT 85 User Manual [Revision 5.0 August 2019] Please note that there must be forward momentum for the motor to activate. READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY VOID WARRANTY.
Electric Scooter - XCT 85 Safety Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or equipment or property damage if not understood or followed. Safety messages have the following symbols: You WILL be KILLED or...
Page 3
Electric Scooter - XCT 85 General Electrical Safety General Electrical Safety General Service Information • Inspect electrical equipment, extension • Electrically grounded equipment must • The equipment must be serviced or cords, power bars, and electrical fittings have an approved cord and plug and repaired at authorised service centres for damage or wear before each use.
Electric Scooter - XCT 85 Safety Symbols The product may have safety warning labels attached to it, explained below. Understand the symbols on your product and their meanings. If any stickers become unreadable, unattached etc, replace them. Flammable Material Hazard...
Page 5
Electric Scooter - XCT 85 Carbon-Monoxide Hazard Pull Hazard Slope / Fall Injury Hazard "Slam Dunk" Warning Do not use the product in Be aware that the product Be aware that using the Do NOT attempt "slam dunk" confined areas or without...
Electric Scooter - XCT 85 Table of Contents Safety ............................. 2 Safety Symbols ............................4 Parts Identification ........................7 Assembly ............................8 Operation ............................9 Controls and Features ..........................9 Mode Indicators ............................9 Power Button ..............................9 Charging the Scooter ..........................10 Using the Scooter ............................
Electric Scooter - XCT 85 Assembly 1. Install the steering rod and open the parking 2. Set the handlebars vertically. bridge. 3. Using the hex wrench provided, tighten the 4. Test the power switch to see if it is working screws on the handle bar.
Electric Scooter - XCT 85 Operation Controls and Features Mode Indicators The control panel has 4 LEDs, indicating a level of charge. While the battery is being consumed, the status indicators will light up and flash, depending on the battery’s charge level.
Electric Scooter - XCT 85 Charging the Scooter 1. Open the charger cover. 2. Connect the charger to the charging port. 3. After charging, close the charger cover. Using the Scooter ATTENTION: Monitor battery usage when in use, the scooter may suddenly slow down as the battery charge reduces.
Electric Scooter - XCT 85 5. Lean your body slightly to the left to turn left and slightly to the right to turn right. Only turn the handle bar slowly. Folding the Scooter 1. Turn the electric scooter OFF. 2. Hold the front pole with one hand while the other hand loosens the lock lever. Then, lower the steering rack.
Electric Scooter - XCT 85 Connecting to the Fireplus App 1. Go to Google Play or Appstore. 2. Search for “Fireplus.” 3. Download the app to your smart device. 4. Then: a. Press the Power button for 3 seconds to turn ON the scooter; The LCD will then show the battery capacity and real time speed.
Electric Scooter - XCT 85 Lithium Battery Care and Maintenance Top 3 Battery Care Requirements 1. Charge battery before first use. The battery may arrive with some charge, regardless of this the battery must be charged for 8 hours on the initial charge and 3 – 4 hours for each subsequent charge.
Electric Scooter - XCT 85 Maintenance Do not use alcohol, petrol, kerosene, corrosive solutions and volatile chemical solvents to clean the electric scooter. Otherwise, it will cause serious damage to the scooter’s body and can disrupt the internal circuitry. Do not wash the electric scooter with a strong water pressure.
Electric Scooter - XCT 85 Adjusting the Handle Bars If the handle bars are shaky, use the M5 hex wrench to tighten the two screws near the folding mechanism. Pumping the Wheels with Air If the wheels are flat or rather soft, connect a pump to the wheel nipple to pump air. Remove the cap of the pin, then tighten the fitting.
Need help?
Do you have a question about the XCT 85 and is the answer not in the manual?
Questions and answers