Star mC-Print3 Easy Setup Manual

80879110
Easy Setup Guide
Introduction
This document explains the setup procedure for the mC-Print3.
For further instructions, please refer to the mC-Print3 (2nd Generation) online manual.
Please read the instructions before using the printer.
You can also see FAQ from the QR code on the inside of the printer.
What's Included
If contents are missing or damaged, please contact the reseller that sold you the printer.
*accessories vary depending on the region where the printer was purchased.
MCP31CI AC Adapter Power Cable*
1
Installing the paper roll
ⓘ
When using a 58mm roll, install the

Pull the open lever and open the printer paper roll guide sold separately.
cover  .
With the notch part A (triangle mark) of the
paper roll guide facing down, angle the
guide to the right and insert it
Position so that the notch part A is aligned
2
1 with the main unit rib B, then slide the
guide from the right
Take the slack of the paper roll before paper
setting, install the paper roll as shown in the
illustration.
When the slid paper roll guide stops, stand
it up vertical
into place
Pull the end of the paper roll out straight
 , and use both hands to close the printer
cover  .
3 To change the paper width, it is necessary
to change the memory switch setting.
4
For details, refer to the Online Manual.
4
mC-Print3 online manual
This Manual
Safety Easy
Instructions Setup Guide
2
Turning ON the Main Unit Power
Place your nails into the gaps in the right
and left sides of the rear cover on the back
of the printer, and then remove the cover.

.
 .
B
2
Connect the power cable to the AC adapter
A
1
 , and connect the cable connector to the
printer as shown in the illustration
Insert the plug into the outlet
2
 , and press until it clicks
 .
Press the power button
that the LED (blue) illuminates
3
4
5
3
Connecting a Tablet or PC
Prepare and connect an appropriate cable to the connector on the printer
according to your device/PC.
When using a commercially available cable, be sure to perform full operation checks
before use.
1
USB-C ®
Communication and Recharge
USB cable
(Make sure that the connector type is appropriate for your device/PC)
iOS ... C to C
* 1
Android ... C to C * 1
PC ... C to A 3 (Communication only) or C to C
*
Plug for the printer:
FAQ
ⓘ
If your PC cannot communicate with the printer using C to C cable, refer
to "Switching the USB-C function manually" on the back page of this
manual, and then switch the function to "Data only".
2
Wired LAN
LAN cable
* 4
Plug for the printer:
ⓘ
DHCP is enabled by default for the wired LAN settings. To continually
use the same IP address, set a static IP address before use. For the static
IP address setting procedure, refer to the Online Manual.
4
Preparing/setting up the configuration app
Use the configuration app to set up the printer from a tablet or PC.
Scan the QR code on the right side or search the app to access the
download site.
When using Android/iOS
 .
Star Quick Setup Utility
 .
 Install [ Star Quick Setup Utility ].
 Open the configuration utility, and select [ Start Guide (Initial
3
1 Settings)] - [ Search Printer].
 Follow the instructions of the utility to connect and set up a tablet.

and confirm ⓘ For a wired LAN connection, use the tablet that is connected to
 .
the same network as the MCP31CI.
4
Once a static IP address is assigned, IP address changes through the DHCP server will not occur, so the specified connection destination

device can be used continuously once set.
ⓘ Driver download site for Mac / Linux environment. (https://www.star-m.jp/supportsite-wsw.html)
For the owners of other companies' trademarks mentioned in this document,see Trademarks in our website (https://www.star-m.jp/eng/trademarks.html).
or C to Lightning
* 2
1
*
*1
*2
*3
*4
 Download [ Star Windows Software ].
 Extract the downloaded software and execute "Setup.exe".

Follow the wizard instructions and complete software installation.
ⓘ The Windows driver is included in the Star Windows Software.
The Star Windows Software can be used to configure the
printer settings and perform an operation test.
iPad
Android
Windows
LAN USB-C
20W(USB PD)
2 1
Cable that conforms to USB2.0 standards, supports current of 3.0A or
higher, and has a maximum length of 2 m.
Apple genuine cable or MFi certified cable with a maximum length of 2 m.
Cable that conforms to USB2.0 standards, has a maximum length of 2 m.
Cable that is compatible with category 5 or higher.
Configuration app
download site
When using Windows
Star Windows Software
Copyright 2023 Star Micronics Co., Ltd.