Related Manuals for STIEBEL ELTRON WPE-I 57 Premium H
Summary of Contents for STIEBEL ELTRON WPE-I 57 Premium H
- Page 1 Operation and installation WPE-I 57 Premium H WPE-I 85 Premium H Ground source heat pump...
-
Page 2: Table Of Contents
Table of contents 1 Special information ........... 3 13 Shutdown (qualified contractors) ......18 13.1 Draining the brine circuit......... 18 2 General information..........3 Symbols in this document ........ 3 14 Specification............. 19 Units of measurement ........3 14.1 Dimensions and connections......19 Other applicable documents ...... -
Page 3: Special Information
Special information Standard: EN 14511, EN 14825 Special information The output data specifically mentioned in text, diagrams and – The following groups of people are not per- technical datasheets has been calculated according to the test conditions of the standard shown in the heading of this section. mitted to use the appliance: Generally, these standardised test conditions will not fully meet –... -
Page 4: Structure Of The Warning Notices
Appliance description Property damage, consequential losses, environmental Signal Meaning word pollution NOTICE Failure to observe this information may result in – Unsuitable spare parts and accessories may jeopardise the property damage, consequential losses or environ- safety of the product and persons using the appliance. Al- mental damage. -
Page 5: Standard Delivery
– Flow temperature sensor T33 ter. WPE-I 57 Premium H | WPE-I 85 Premium H Ventilation: Inverter cooling WPE-I 57 Premium H and WPE-I 85 – Pressure hose SD 40-0.8 G Premium H – Pressure hose SDB 50-0.8 G A fan is installed at the top right-hand side of the appliance. -
Page 6: Creating Wall Outlets
– Ensure that the entire appliance frame is in full contact with WPE-I 57 Premium H | WPE-I 85 Premium H the substrate. Uneven substrates can increase sound emis- sions. -
Page 7: Siting The Appliance
Installation (qualified contractors) WPE-I 57 Premium H | WPE-I 85 Premium H D0000117952 D0000082845 Siting the appliance u Undo the closures on the top cover. Unpacking the appliance u Pull the top of the front panel forwards. u Remove the packaging material. - Page 8 Charge the brine circuit via the "brine drain" connection. PG 10 Heat transfer medium as concentrate 236307 based on propylene glycol WPE-I 57 Premium H Content: 10 l WPE-I 85 Premium H PG 30 Heat transfer medium as concentrate 236306 based on propylene glycol Content: 30 l...
-
Page 9: Installing The Heating Circuit
Connect the heat pump on the heating side. u Install air vent valves at the required positions. WPE-I 57 Premium H u Install the circulation pump in the heating flow. WPE-I 85 Premium H u Install a fill connector with a non-return valve. -
Page 10: Air Duct
Installation (qualified contractors) 6.7.1 DHW heating with hot gas technology u The refrigerant is highly flammable. Mark the installation area with an Atex symbol. u Connect the "Heat pump DHW flow" connection from the DHW cylinder to the "Hot gas DHW flow optional" connec- tion. - Page 11 6.9.3 Routing supply lines Heat pump Short-circuit capacity [MVA] WPE-I 57 Premium H WPE-I 85 Premium H 6.9.1 Opening the terminal area The terminals are located inside the appliance control panel, behind the front fascia.
-
Page 12: Temperature Sensor
Commissioning (qualified contractors) 6.9.4 Additional components Temperature [°C] PT 1000 sensor Resistance [Ω] u If you want to install a mixer, use one with a control voltage 1155 of 10 V. 1194 u Connect the power cables for the additional components in 1232 accordance with the wiring diagrams. -
Page 13: Testing Components Manually
Commissioning (qualified contractors) 7.1.4 High limit safety cut-out of the electric emergency/ Diverter valve auxiliary heater u Test the diverter valve. At ambient temperatures of below -15 °C, the high limit safety – 0 = Heating cut-out of the electric emergency/auxiliary heater may trip. –... -
Page 14: Commissioning: Adjusting The Heating Curve
Commissioning (qualified contractors) Commissioning: Adjusting the heating curve Checkpoint Reference to instruc- Com- tions pleted? The efficiency of a heat pump decreases as the flow temperature Have all the pipes in the rises. Therefore adjust the heating curve with care. A heating heating system been curve that is set too high leads to the zone or thermostatic sized correctly? -
Page 15: Cleaning
Cleaning Checkpoint Reference to instruc- Com- 11 Troubleshooting tions pleted? Has the high pressure switch been tested? Fault Possible cause Remedy There is no hot wa- No voltage at the Check the fuses / ter or the heating appliance. MCBs in your fuse Cleaning system remains box / distribution... - Page 16 Troubleshooting (qualified contractors) Message Class Description Message Class Description High pressure High pressure switch activ- DHW control sensor B Sensor alarm switch ated DHW return Sensor alarm Low pressure Paused at low pressure, Cooling cylinder Sensor alarm more than 5 times in sensor 5 hours, low pressure limit Cooling circuit flow...
- Page 17 Troubleshooting (qualified contractors) Other faults Message Class Description Heating circuit 2 Temperature deviation ac- Fault Possible cause Remedy control cording to alarm settings for heating circuit 2 The heat pump is The wrong heat u Check which not running. pump is set on the Heating circuit 3 Temperature deviation ac- model has been...
-
Page 18: Shutdown (Qualified Contractors)
13.1 Draining the brine circuit u Use the connection on the low pressure side and the high pressure connection in the liquid refrigerant line next to the dry filter. WPE-I 57 Premium H WPE-I 85 Premium H D0000117945 | WPE-I 57/85 Premium H... -
Page 19: Specification
Specification 14.1 Dimensions and connections 14 Specification WPE-I 57 Premium H WPE-I 85 Premium H D0000117920 WPE-I 57 Premium WPE-I 85 Premium Entry electrical cables I Entry electrical cables II Hot gas DHW flow optional Diameter Hot gas DHW return optional... -
Page 20: Wiring Diagram
Specification 14.2 Wiring diagram FR 7 FR 6 Temp Temp Pressure CP control Heat Sys Sensors Sensors & feedback Y606 Y607 Y608 Y609 Y611 Y612 Y613 Y614 Y615 Y616 Y610 FR 5 Accessory Exspansion EEXV MBe2 FR 4 24AC Supply 24V--- 100-240V 0-10V... -
Page 21: Output Diagrams
Specification 14.3 Output diagrams 14.3.1 WPE-I 57 Premium H Heating output WPE-I 57 heating output Power consumption WPE-I 57 power consumption www.stiebel-eltron.com WPE-I 57/85 Premium H |... - Page 22 Specification Coefficient of performance WPE-I 57 coefficient of performance 14.3.2 WPE-I 85 Premium H Heating output WPE-I 85 heating output | WPE-I 57/85 Premium H www.stiebel-eltron.com...
- Page 23 Specification Power consumption WPE-I 85 power consumption Coefficient of performance WPE-I 85 coefficient of performance www.stiebel-eltron.com WPE-I 57/85 Premium H |...
-
Page 24: Data Table
Specification 14.4 Data table WPE-I 57 WPE-I 85 Premium H Premium H Performance data applies to new appliances with clean heat ex- Weights changers. Weight The power consumption figures for the integral auxiliary drives Connections are maximum values and may vary subject to operating point. Connection, hot gas mm 28.00 28.00... -
Page 25: Guarantee
Guarantee 15 Guarantee The guarantee conditions of our German companies do not ap- ply to appliances acquired outside of Germany. In countries where our subsidiaries sell our products a guarantee can only be issued by those subsidiaries. Such guarantee is only granted if the subsidiary has issued its own terms of guarantee. - Page 26 | WPE-I 57/85 Premium H www.stiebel-eltron.com...
- Page 27 www.stiebel-eltron.com WPE-I 57/85 Premium H |...
- Page 28 Co m f o r t t h r o u gh Te c h n o l o g y STIEBEL ELTRON GmbH & Co. KG Dr.-Stiebel-Straße 33 | 37603 Holzminden | Germany info@stiebel-eltron.com | www.stiebel-eltron.com 4 0 1 7 2 1 3 6 6 3 9 9 7...
Need help?
Do you have a question about the WPE-I 57 Premium H and is the answer not in the manual?
Questions and answers