Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Bestway LAY-Z-SPA
Summary of Contents for Bestway LAY-Z-SPA
- Page 1 LAY-Z-SPA ® bestwaycorp.com/support...
- Page 4 A: 1...
- Page 5 • For the installation instructions, refer to the illustration steps on the package. Drawings are for illustration purposes only. May not reflect actual product. Not to scale. • Bestway will not be responsible for any damage caused to the hot tub due to mishandling or failure to follow these instructions.
- Page 6 TABLE OF CONTENTS TABLE OF CONTENTS DISASSEMBLY & STORAGE INSTRUCTIONS PAGE 16 • Be sure that your hot tub is completely clean and dry before storage. If all parts are not completely dry, mold may result. • Store in a dry place with a moderate temperature between 15ºC (59ºF) and 38ºC (100ºF). TROUBLESHOOTING PAGE 18 •...
- Page 7 SAFETY INFORMATION • Never operate any electrical appliance when in your spa or when your body is wet. Never place any electric appliance, such as a light, telephone, radio, or television, within 2 m (6.6 feet) of the spa. • Install at least 2 m (6.6 feet) from all metal surfaces. •...
- Page 8 SAFETY INFORMATION • Never wear your contact lenses when in your spa. DANGER - Risk of Injury. The suction fittings in this spa are sized to match the specific water flow created by the pump. Should the need arise to replace the suction fittings or the pump, be sure that the flow rates are compatible.
- Page 9 • Whenever the spa is emptied, the filter should be cleaned (and drained/dried, where applicable). • Please examine equipment before use. Notify Bestway at the customer service address listed on this manual for any damaged or missing parts at the time of purchase. Verify that the equipment components represent the models that you had intended to purchase.
- Page 10 SAFETY INFORMATION • When the spa is being used, the cover should be placed in a clean, dry area, otherwise it can pick up dirt and bacteria. Covers should not be put on wooden tables or wooden decking because of the risk of bleaching the wood.
- Page 11 PRODUCT DESCRIPTION HOT TUB HEATER SPECIFICATIONS: Power Rate 220-240V AC, 50Hz, 2050W PARTS & TOOLS NEEDED Compare the parts in your box to the parts listed on the top of the package. Verify that the equipment components represent the model that you had intended to purchase. If any parts are damaged or missing at the time of purchase, visit our website bestwaycorp.com/support.
- Page 12 SETUP INSTRUCTIONS INDOOR INSTALLATION: Be aware of these special requirements if you install the hot tub indoors. • Humidity is a natural side effect of hot tub use that could cause damage to property without proper precaution. • Determine the effects of moisture on exposed wood, structural materials, or surrounding objects in the proposed location.
- Page 13 USAGE INSTRUCTIONS CONTROL PANEL AIRJET WITH WI-FI AIRJET ON/OFF BUTTON: After activating the RCD/PRCD, press and hold the button for 2 seconds. button will light up green and the control panel can now be used. Press and hold the button for 2 seconds to turn off all activated functions. CELSIUS/FAHRENHEIT TOGGLE: The temperature can be displayed in either Fahrenheit or Celsius.
- Page 14 USAGE INSTRUCTIONS MASSAGE SYSTEM BUTTON: Press the button to activate the massage system, which has a 30-minute auto-shutoff feature. The light of the button becomes red when activated. Do not run the massage system when the cover is attached. Air can accumulate inside the hot tub and cause irreparable damage to the cover.
- Page 15 USAGE INSTRUCTIONS HEATING TIMES For the water to reach 40°C (104°F), the time required is based on the starting water temperature and outdoor temperature. The data below is purely for reference. To display the current water temperature, run the filter system for at least a minute. Outdoor Temperature Water Temperature Set Temperature...
- Page 16 MAINTENANCE INSTRUCTIONS Chemical Tablets (Not Included): • Remove the chemical dispenser from the hot tub when the hot tub is in use. • After performing chemical maintenance and before using the hot tub, use a test kit (not included) to test the water chemistry.
- Page 17 DISASSEMBLY & STORAGE INSTRUCTIONS REPAIRING When repairing the cover or interior floor: Use the provided repair patch to repair tears or punctures. • Clean the area, and carefully peel the patch. • Stick the patch over the damaged area. • Wait 30 seconds before re-inflation. When repairing the walls or exterior floor: Use the provided repair patch and glue (not included) to repair tears or punctures.
- Page 18 TROUBLESHOOTING Problems Probable Causes Solutions Pump stopped Power failure. Check power source. working Power circuit is broken. For assistance, please visit the support section on our website, www.bestwaycorp.com. Pump is not Temperature set too low. Set the hot tub to a higher temperature; refer heating properly to pump operation section.
- Page 19 TROUBLESHOOTING Problems Probable Causes Solutions Water leaks from The strainer is loose. If the strainer is loose, tighten it with the wrench. the pump Seals are not in the If the seals are not in the correct position, open the gears correct position.
- Page 20 TROUBLESHOOTING WI-FI LED LIGHT STATUS Light Status Meaning Solutions Light flashes Ready to connect to the router. Connect to the Wi-Fi using your phone. slowly Light is on Connected to the router. N/A - already connected to the Wi-Fi. Light flashes Lost Wi-Fi signal.
- Page 21 ERROR CODES Error Code Probable Causes Solutions The water temperature is The hot tub is not designed to operate with water The pump’s lower than 4°C (40°F). temperatures lower than 4°C (40°F). Unplug the pump thermometer and only re-start the pump when the water temperature reads the water reaches 6°C (42.8°F).
- Page 22 ERROR CODES Error Code Probable Causes Solutions An appliance in your home Call an electrician immediately to understand if power is Electricity is may have an electric leak. flowing inside the grounding connection. If the problem detected from the continues, to use your hot tub safely, we strongly ground wire.
- Page 24 / Marken, abweichend in bestimmten Ländern unter Lizenz von / I marchi commerciali sono utilizzati in alcuni paesi su licenza Bestway Inflatables & Material Corp. Manufactured by / Fabriqué par / Fabricado por / Produziert von / Prodotto da Bestway Inflatables & Material Corp., No. 208 Jin Yuan Wu Road, Shanghai, 201812, China.
Need help?
Do you have a question about the LAY-Z-SPA and is the answer not in the manual?
Questions and answers