WMF Kult X Manual

Overview

Layout

1. Induction hob
2. Fan
3. Touch control panel
4. Plug

Touch control panel

5. On/Off button
6. Start/Pause button
7. Power level controller
8. Direct select programmes
9. Display
10. Timer button
11. LED
12. Power-Sharing

Functions

Touch control panel (3)
The double induction hob has two hotplates. You can use the two touch control panels (3) to set the two hotplates independently.
The functions of the induction hob are activated by tapping the corresponding symbol buttons. The control panel reacts to being tapped lightly without needing to apply pressure. To work correctly, the control panel has to be clean and dry. The corresponding LED lights up red when a function is activated, e.g. after switching the appliance on.

Setting power levels (7)
The appliance has eight power levels that are set and changed directly through the power level controller and displayed correspondingly through the red LEDs. If you touch a position on the power level controller, the corresponding level is selected. All LEDs from the lowest level (left) to the selected level are then lit. You can also change the selected power level by sliding your finger from left to right, or from right to left along the power level controller.

Display (9)
To show the timer. The timer can be reset any time by using the + and - (10) buttons.

Set timer (10)
The timer is set through the + and – (10) buttons. If you tap on one of the buttons, the time is changed by 1 minute. If you tap and press one of the buttons for a longer time, the time is changed progressively in 10 minute steps. The timer can be set to a value between 0:01 and 9:59 by directly using the 8 power levels (7), without selecting a programme. The timer can be changed at any time using the programme functions and the 8 power levels (7).

Power-Sharing (12)
The Power-Sharing function ensures optimum usage of the total power available. If both hotplates are operated at the same time, they share the power settings via the Power-Sharing function. As soon as the Power-Sharing function is active, it is indicated with the red LED.
Note: If one hotplate is working at power level 7–8, the maximum power level for the other is power level 5.

Direct select programmes (8)
A programme can be selected by tapping the appropriate symbol button. If you wish to change the programme while the hob is in operation, simply tap and hold the appropriate symbol button for a whole second.

Button	Function	Approx. Temp.°C*)	Power level Preset	Performance Adjustable	Timer Adjustable
	Keep warm Keep food at serving temperature	Approx. 60	2	1-3	10-120 mins.
	Heating up milk, melting e.g. chocolate	Approx. 50	2	1-2	1-30 mins.
	Simmer Cook in hot water below boiling point	Approx. 85	3	1-4	10-120 mins.
	Cooking/Steaming	Approx. 95	6	2-8	1-120 mins.
	Fry Quick frying of meat or fi sh	Approx. 200	7	4-8	1-30 mins.
	Boost = Rapid heating of larger quantities to maximum temperature, for example	Approx. 230	8	No	1-5 mins.

Note: By selecting the direct select programmes (8) (with the exception of Booster), the power levels (7) can be raised or lowered to achieve quicker or slower warming.
Depending on which programme has been selected, the timer settings that are predefi ned for the programme functions can be changed by using the + and – (10) buttons.

It must be ensured that oils and fats that are suitable for use at high temperatures are used for the Fry and Booster programmes.
*) The temperatures of the heated foodstuffs may deviate from those shown here as the temperatures are dependent on the cookware used, amongst other factors.

Operating procedure
The induction hob offers 3 different functions:

• Use of the power levels 1-8 without timer function
• Use of the power levels 1-8 with timer function
• Using direct select programmes (8)

Use of the power levels (7) without timer function

Action	Touch button	Display
Plug the appliance in. Appliance is in standby mode.
Tap the On/Off button; appliance is in operational readiness mode
Position the pan on the hob.
Set the desired power level 1-8.
Tap the Start/Pause button. Cooking process starts. The "Appliance in use" symbol is shown in the display
Action	Touch button	Display
Adjust the power level as required, e.g. when the boiling point is reached.
If necessary, tap the Start/Pause button again: Cooking process is paused The "Appliance in use" symbol disappears Start/Pause LED fl ashes Tap on theStart/Pause button to resume the cooking process
Switching off the hob by pushing the On/Off button twice. Note: The fan runs on for a few seconds.
Pull out plug.

Note: If the induction hob is in pause mode it switches itself to standby automatically after 10 minutes if the control panel is not operated.

Use of the power levels (7) with timer function

Action	Touch button	Display
Plug the appliance in. Appliance is in standby mode.
Tap the On/Off button, appliance is in operational readiness mode.
Position the pan on the hotplate.
Set the desired power level 1-8.
Set the timer with +/- buttons.
Tap the Start/Pause button. Cooking process and Timer starts. The "Appliance in use" symbol is shown in the display
Change the power level if required
If necessary, tap the Start/Pause button again: Cooking process and Timer is paused The "Appliance in use" symbol disappears Start/Pause LED fl ashes Tap on the Start/Pause button to resume the Cooking process and Timer
Once the defi ned timer time has elapsed, the appliance switches automatically to operational readiness mode.
After one minute, the appliance switches automatically to standby mode. Alternatively, press the On/Off button. Note: The fan runs on for a few seconds.
Pull out plug.

Note: If the induction hob is in pause mode it switches itself to standby automatically after 10 minutes if the control panel is not operated.

Using direct select programmes (8)

Action	Touch button	Display
Plug the appliance in. Appliance is in standby mode.
Tap the On/Off button; appliance is in operational readiness mode
Position the pan on the hotplate.
Select programme. For example "Cooking/Steaming".
Adjust the power level if required.
Adjust the timer with + / - if required.
Tap the Start/Pause button. Cooking process and Timer starts. The "Appliance in use" symbol is shown in the display
If necessary, tap the Start/Pause button again: Cooking process and Timer is paused The "Appliance in use" symbol disappears Start/Pause LED fl ashes Tap on theStart/Pause button to resume the Cooking process and Timer
Once the defi ned timer time has elapsed, the appliance switches automatically to operational readiness mode.
After one minute, the appliance switches automatically to standby mode. Alternatively, press the On/Off button. Note: The fan runs on for a few seconds.
Pull out plug.

Note: If the induction hob is in pause mode it switches itself to standby automatically after 10 minutes if the control panel is not operated.

Additional instructions for use
You can change the cooking parameters at any time while cooking:

• Change the power level using the power level controller (within the range of the predefi ned programme (8). See Programme table).
• Adjust the timer with the + and - (10) buttons.
• Change the programme by selecting another programme. In this case, the corresponding symbol button must be tapped and held for 1 second. This prevents an accidental change of programme from occurring.

Cleaning and care

• Pull out the mains plug before cleaning the appliance.
• Ensure that no water gets into the appliance.
• Never submerge the appliance, cable or plug in water or any other liquids.
• Do not use any cleaning agents that are abrasive or that contain benzine.
• Do not bring any fl ammable (infl ammable), acidic or alkaline material or substances close to the appliance as this could shorten the appliance's working life and a burst of fl ame can occur when switching the appliance on.
• Wipe down the ceramic area with a damp cloth or you can use a mild, non-abrasive soap solution.
• Wipe down the casing and control panel with a damp cloth or you can use a mild cleaning agent.
• Dry the whole appliance completely before next use.

Errors

• The appliance is not intended for purely commer cial use.

Before use
Read the instruction manual carefully. It contains important information about the use, safety and maintenance of the appliance. It should be kept in a safe place and passed on to any subsequent users. The appliance may be used only for the intended purpose in accordance with these instructions for use. The safety precautions must be observed during use.

Technical data
Mains voltage: 220 – 240 V~, 50 – 60 Hz
Power consumption: 3500 Watt
Protection class: I

Additional safety information

• Persons with heightened electro-sensitivity shouldn't be in the immediate area of the appliance any longer than is necessary.
• Persons fitted with cardiac pacemakers or medication pumps who are uncertain whether using the appliance is harmless for them, should speak with their doctor.
• The appliance must not be operated on a metal base, as this can heat up considerably.
• To ensure proper ventilation of the appliance, make sure that the appliance is at least 10 cm away from other objects or walls.
• The cool air is drawn in by the underside of the appliance. Do not cover or block any of the appliances openings.
• Position the cookware centrally on the hob. In this way, the base of the pan largely screens the electro-magnetic field.
• Do no remove any covers from the appliance.
• Do not place any empty piece of cookware on the hob when it is switched on. Heating up an empty cooking pot causes the overheating protection to be triggered.
• Do not heat up any sealed cans. There is a risk of explosion!
• The appliance should be connected only to earthed wall sockets that have been installed in accordance with the regulations. The power cable and plug must be dry.
• The connection cable must not come into contact with hot appliance parts.
• Stop using the appliance and/or pull the mains plug out of the socket immediately if:
  • The appliance or the mains cable is damaged;
  • You suspect that the device may be defective following a fall or similar incident. In such cases, arrange for the appliance to be repaired.
• Do not touch the surface of the ceramic hotplates while they are still hot (H is shown in the display).
• Do not leave the appliance unattended.
• Pull out the mains plug
  • If the appliance malfunctions during use;
  • Before cleaning and care;
  • After use.
• Do not immerse the appliance in water to clean it.
• We accept no liability for any damage caused as a result of misuse, incorrect operation or improper repairs. Warranty claims are likewise excluded in such cases.

Use
The induction cooker is intended for the warming, cooking and frying of foodstuffs and may only be used indoors. It is only intended for domestic use. The cookware used must be suitable for induction cookers.
Induction hobs require special cookware.

Suitable cookware

• Cookware with a ferromagnetic base
• Stainless steel (with iron core in the base), cast iron
• Enamel frying pans with a magnetic base
• Recommended cookware diameter: 180 mm to 280 mm
• Max. weight 6 kg (pot and content)

Unsuitable cookware

• Ceramic pots, heat-resistant glass
• Copper, aluminium or other non-metallic cookware
• Cookware with feet
• Containers with a curved base
• Containers made from stainless steel without a magnetic steel core
• Containers without a flat base

Carry out your own test!
You can easily test the suitability of the cookware yourself:
Hold a magnet next to the base of the pan. If there is a strong magnetic attraction, the cookware is suitable. The induction hob only works with appropriate cookware. The appliance recognises if the cookware is not suitable and behaves as if no cookware is on the hotplate: The hob doesn't switch on.