Page 2
Foreword Thank you for choosing BYD. To better use and maintain the vehicle, please read this manual carefully and keep it for future reference. Special instructions: BYD Auto Industry Co., Ltd. recommends that you choose genuine spare parts and use, maintain, and repair the vehicle in accordance with this manual.
Page 3
(if any) related to this product, or consult the dealer who sold the product to you. Sustainability As a pure electric passenger vehicle, the BYD HAN EV is an environmentally friendly product. Please visit https://reach.bydeurope.com for environmental protection information about the vehicle.
Illustration Index Exterior P175 Trunk Lid Tire P138 Carrying Luggage Snow Chains P177 Using Mode 2 Charging Cable* If a Tire Goes Flat Using AC Charging Piles* Combination Light P172 Using DC Charging Piles* Hood P172 External Discharging Method* Coolant P137 P173 Power Side Mirrors...
Interior Light Switches Hazard Warning Light P153 Cup Holder Adjusting the Steering Wheel with Power* Seat Adjusting Steering Wheel P153 Center Console Cubby Manually Using Seat Belt P154 Bill Box P157 Wireless Phone Charger...
Doors Opening with Interior Door Handle Driver's Door Switches Central Locking Memory System of the Seat Child Protection Locks P172 Opening the Hood Opening the Trunk from the Inside...
Until then, do not use the restraint force. corresponding seat. BYD has highly emphasized that all Seat Belt Pretensioning by Motor* ● occupants should always fasten their seat belts while in the vehicle. Failure...
motor drives the webbing to retract to Keep the lap section of the belt as ● reduce the possible excessive slack of close as possible to the hip and do not seat belts. keep it on the waist. REMINDER Do not pull out the belt webbing ●...
Page 15
After an accident, have the seat If the seat belt does not retract ● ● belts checked at a BYD authorized smoothly and automatically, pull it out dealer or service provider. If the and check whether it is twisted. pretensioner function is activated, the seat belt must be replaced.
● after the vehicle is started, visual and or function failure, contact audible alarms go off and continue until a BYD authorized dealer or the corresponding seat belt is properly service provider. Do not use fastened. the corresponding seat until the functions return to normal.
If an accident requires front airbags order to protect occupants from ● activation, the vehicle will engage high-voltage danger. Contact a automatic braking. BYD authorized dealer or service provider for inspection. Speed reduction, along with ● intervention by additional driving systems (Electronic Stability Control...
Knee Airbags If the vehicle you purchased is equipped with a knee airbag (located inside the lower trim of the dashboard), when the electronic control unit (ECU) of the airbag system detects a moderate to severe front impact during vehicle travel and the triggering conditions are met, the knee airbag will deploy to help protect the legs and knees of occupants.
When a moderate to severe side ● CAUTION impact is detected during vehicle travel and the triggering conditions are If the seatbacks get wet from ● met, the side curtain airbag deploys to rain or splashes, the side airbag protect the head of the occupant on system may not work properly.
Page 20
The vehicle's nose hits the ground when going down a steep slope. The ECU of the BYD airbag system ● has been set up with considerations of common misuse and road conditions.
Page 21
The vehicle goes under a truck or another The vehicle hits a wall or a vehicle at a large vehicle. side other than the front side. The tail of the vehicle is hit by another Parts other than the passenger vehicle.
Page 22
WARNING is leaning forward or sitting improperly, airbag deployment can increase the risk of injury. Do not paste stickers, cover or ● decorate the hub cover of the steering wheel, the right side surface of the dashboard or the surface of A, B, and C-pillar trims. Clean these surfaces with a dry or The lateral side of the vehicle hits a damp cloth, without applying too...
Page 23
It is recommended that you contact a BYD authorized dealer or service Do not change any component ● provider immediately if any of the of the airbag system, including following situations occurs.
An impact to a vehicle door in an ● accident is not adequate to cause the airbag to deploy. The surface of the seat with a ● side airbag is scratched, cracked, or damaged similarly. Decorative (liner) parts at A-pillar with ●...
Secure the top tether when installing ● the child restraint system. Installing Child Restraint Systems Follow the installation instructions provided by the child restraint manufacturer. Secure the child restraints to the rear outboard seats. Children must use a suitable child ●...
Page 26
REMINDER Secure the top tether when ● installing the child restraint system. Installing child restraint systems: ● 1. Open the anchorage lever trim cover and install the child restraint system to the seat. 3. Fasten the snap hook to the anchor support and tighten the top tether to ensure the strap is buckled securely.
Page 27
Never install a rear-facing child ● restraint on the seat protected by a front airbag (in the active state), otherwise in the event of an accident, the force of rapid deployment of the front passenger airbag will result in death or serious injury to the child. Recommended seating positions for installing child restraint systems Seat (or Other Positions) Weight Group...
Seat (or Other Positions) Weight Fixed Front Rear Size Rear Middle Group Module Passenger Outboard Seat Seat Seat ISO/L2 Group 0 ISO/R1 (up to 10 kg) ISO/R1 Group 0+ ISO/R2 (up to 13 kg) ISO/R3 ISO/R2 ISO/R3 Group 1 ISO/F2 (9-18 kg) ISO/F2X ISO/F3...
● personal data is collected and Unlocking the door with a valid smart ● processed when you use a BYD vehicle. key. For a more detailed overview on data Using the microswitch to unlock the ●...
Page 30
Personal data that is collected and ● safety. processed mainly include in-vehicle data, remote-services-related data, Depending on the country and setup, ● and other data, as further specified various vehicle information can be below. transmitted to the data center of BYD...
Page 31
BYD services through the performance status. vehicle's infotainment system network devices. Other BYD is not liable for any such services Infotainment system ● provided by any other party. Depending on vehicle configuration, ●...
Page 32
You are responsible to check the laws If required by law, BYD may also ● ● of your residence before turning on be obliged to disclose data upon your OFC or IFC (for instance, in some request to governmental authorities in...
Instrument Cluster Instrument Cluster View Instrument Cluster Power meter Speedometer Time Total mileage Gear status Remaining driving range Outside temperature State of charge (SOC)
● remains in simple mode after simple mode for safe driving. In those actions have been this mode, the instrument cluster taken, promptly contact a BYD continues to display driving authorized dealer or service related information normally provider for inspection.
Page 37
High beam indicator HMA indicator* ICC indicator Front fog light indicator* AVH indicator Hill descend control indicator Exterior light switch indicator AVH standby indicator Discharge indicator OK indicator Economic mode ACC speed indicator Sport mode PCW indicator (green) Normal mode AEB warning light High-voltage battery low SOC Rear fog light indicator...
Page 38
ABS fault warning light Snow mode indicator BSD indicator* AVAS OFF indicator High-voltage battery PCW warning light (red) overheating warning light Low-voltage power system fault Motor overheating warning light warning light Powertrain fault warning light Door status indicator Motor coolant overheating TSR indicator indicator Seat belt reminder indicator...
Page 39
flashes, the message monitored by the warning light system. "Please check TPMS" is displayed In that case, contact a BYD authorized on the instrument cluster, and the dealer or service provider for vehicle tire pressure is displayed as "---", it inspection as soon as possible.
Page 40
In that case, contact a BYD authorized which appears suddenly, because dealer or service provider for vehicle braking at this time can render inspection as soon as possible.
Page 41
● indicate a problem. means there is a fault in components monitored by the warning light system. In that case, contact a BYD authorized Steering system fault warning light dealer or service provider for vehicle inspection as soon as possible.
Page 42
It is recommended to contact a BYD When the warning light flashes, it is authorized dealer or service provider recommended to immediately stop the for rescue as soon as possible.
Page 43
Thereafter, if the system fails, this light down the vehicle. When the indicator will light up again. It is recommended flashes, it indicates the coolant level is to contact a BYD authorized dealer or low. Add coolant promptly. service provider for inspection as soon as possible.
Page 44
The lane departure assist system is faulty. In ADAS is limited* this case, park the vehicle, and contact a BYD authorized dealer or service provider. The function of the multi-purpose camera is Please check the multi- limited.
The button (coin) battery in the ● You can register a spare key smart key is hazardous and both ● for the same car. In this case, new and used batteries are to be contact a BYD authorized dealer or service provider immediately.
Page 48
It is recommended to contact a use other electronic medical BYD authorized dealer or service devices should also consult the provider for inspection as soon manufacturer on the use of as possible.
In order to ensure vehicle safety, handle it with care. If it is lost, going to BYD authorized dealer or service provider for blocking of the lost card and re- configuration is recommended.
Page 50
pull out the mechanical key. Pull on CAUTION the door handle to open the door. As this vehicle is equipped with To unlock the driver's door: Turn the ● ● a child protection lock, the rear key clockwise. doors can only be opened with To unlock the driver's door: Turn the the interior door handle when the ●...
Page 51
If the hood or trunk is not closed, ● WARNING the side mirrors do not fold, the turn signals do not flash, and the alarm When using the remote control ● sounds once. function to raise windows, pay attention to the safety of Unlocking: occupants in the vehicle, and use Press the unlock button.
Page 52
smart key. All doors unlock and turn signals flash twice. The hidden door handle extends automatically and the turn signal flashes twice. If the anti-theft alarm system is ● armed, open a door within 30 seconds after the unlocking. or all doors will relock automatically and the four door handles retract.
Page 53
1. Flip the rear center console cubby to open its cover. ① Trunk close button When the trunk lid is open and ● stationary, press this button to close 2. Open the trunk lid by pulling its the lid. emergency unlocking latch. Press this button a second time to stop ●...
All doors automatically lock at vehicle ● speeds above 8 km/h. Press the START/STOP button to switch ● the ignition off. Then, all doors are unlocked automatically. Locking/unlocking all doors concurrently With the anti-theft alarm system ● disarmed, the backlight of the central lock button turns on if the vehicle is locked and off...
Page 55
● cannot work properly due to system mobile phone. failures, bring all smart keys to a BYD The smart key is in contact with or authorized dealer or service provider ● covered by a metal object.
smart key in the vehicle or within two door, press the child protection lock meters from the vehicle. button for the corresponding side again or use the exterior door handle. Receiving strong electromagnetic ● waves for a long time drains the WARNING battery of the smart key quickly.
WARNING REMINDER Sitting on a folded seatback, Adjust the seat position before ● ● in the trunk, or on cargo fastening seat belts. is prohibited. Improper seating While adjusting a seat, do not let position or improperly fastened ● it hit against any passenger or the seat belts can result in personal luggage.
Page 58
REMINDER Releasing the switch stops the ● seat in this position. Do not place anything under the seat as this may prevent the seat from operating. Adjusting the Lumbar Support Lumbar support adjustment switch Memory System* Press the front, rear, upper, or lower ●...
Page 59
recorded, and the memory setting WARNING finishes. Ensure that no part of your body is Press and hold the "SET" button on ● ● within the seat's movement range the seat memory switch, and at the during the seat memory wake-up same time press either "1"...
Swipe the left/right button to select Enable or disable the heating of the ● ● the rear seat to be heated or rear windshield and side mirrors by ventilated. using the heating switch for the rear windshield and side mirrors. Heating adjustment Seat heating: On the infotainment Rear Seats...
Steering Wheel Steering Wheel Switches Panoramic view Call Custom Speech recognition Distance - Right Distance + Scroll button +/Reset or -/Set Left Lever Mode Instrument cluster/Back The audio control switch is accessible Activates the adaptive cruise control ● when the ignition is switched on. (ACC) system and uses the previous system settings.
Page 62
Turns the cruise system on or off. Roll the button downward to ● ● decrease the volume. The button is -/Set non-operational when the volume reaches the lowest. Sets the current speed to the target ● cruise speed. Press down the button to mute. ●...
When the instrument cluster is not in Press the button to play the next ● ● the menu mode, press this button to track (track number +1). view the instrument cluster menu. Press the button to select a ● When the instrument cluster is in menu ●...
Page 64
WARNING of impaired vehicle control, which can lead to accidents. After adjusting the steering wheel, ● move it up and down to verify that it is securely locked. Steering Wheel Greeting* With the vehicle having no speed (≤ WARNING ● 3 km/h), if the ignition is switched off...
3. Voice control: Activate voice control to turn the heated steering wheel on or off. CAUTION The heated steering wheel shut off ● automatically after working for 30 minutes. Power-Assisted Steering Mode Settings Auto lights The feel of steering assistance varies Set the light switch to .
Page 66
Low beam Overtaking light Pull up the lever (toward the steering Set the light switch to to turn on the wheel) to turn on the overtaking light. low beam. Release the lever for the light switch to automatically reset. The overtaking light turns off.
Page 67
Auto light off Conditions to activate the auto light off ● function: To activate this function, set the light switch to and switch off the vehicle power. When the auto light off function ● is activated, the headlights, position lights, rear fog lights, and high beams turn off...
Page 68
Recommended Lighting Loading Conditions Level One person in the driver seat The driver, plus one passenger in the front seat All the seats occupied All seats occupied, plus an evenly distributed load in the trunk Driver, plus an evenly distributed load in the trunk Vehicle loading conditions may differ.
BYD authorized dealer front windshield inside the vehicle. or service provider to calibrate the sensors, so as to avoid affecting To use the auto wiper function, turn ●...
CAUTION shapes, which could lead to wiper malfunction. After the snow has melted, it may result in automatic wiping of the wiper. REMINDER With the wiper handle at , the ● wiper will perform a wiping action WARNING whenever the wiping sensitivity is increased by one shift;...
Page 71
The anti-pinch function may not ● work if an object is jammed into the window when it is almost Window Anti-pinch completely closed. Anti-pinch function Contacting a BYD authorized ● dealer or service provider for maintenance is recommended if...
Press this button to fold or expand side CAUTION mirrors. the windows' automatic closing function or anti-pinch function is not working normally. Central Locking The driver's door is equipped with power door lock switches. Both switches can lock or unlock all doors. ①...
The mileage per trip (Mileage 1 or power, comfortable driving and riding ● Mileage 2) can be calculated using a experience, and better economy. trip odometer. Normal mode (NORMAL): standard ● settings mode, the default driving Mode Switches condition. Sport(SPORT ): The vehicle shows ●...
Hazard Warning Light open the sunroof completely. If button ① or ② is pressed when the sunroof Switch is opening, the sunroof will stop at its current position. When the button is pressed, all turn signals and turn signal indicators on the instrument cluster start flashing.
Page 75
WARNING Passengers must refrain from ● sticking hands or their heads out through the sunroof. Otherwise, severe injury or even death may occur. CAUTION Trying to open the sunroof in Closing the sunshade ● outside temperatures below 0℃ Press and hold the sunshade close or when it is covered in snow or ●...
E-Call Switch Emergency Call(E-Call)* E-Call* refers to emergency call. The E- ● Call system can be triggered manually within two seconds by pressing and holding the SOS button. The E-Call system activates ● automatically in the event of airbag deployment or the detection of a Side Interior Lights severe collision.
USING AND DRIVING Charging/Discharging...... 78 Battery..........91 Usage Precautions......95 Starting and Driving......99 Driver Assistance......107 Other Main Functions..... 136...
● implanted electronic devices. Consult during charging, stop immediately and the device manufacturer before contact a BYD authorized dealer or charging. service provider. Charge the vehicle in a relatively safe Always observe the following charging ●...
Page 80
Hold the charging connector, align ● the connector with the charge port and push it in, making sure that they are properly connected. When charging is complete: ● Stop charging first and make sure the ● charge port is unlocked. These signs refer to standardized ●...
Page 81
disconnected. The locking mechanism of battery temperature control system can damage the charging equipment may be affected by the A/C in and the vehicle if the vehicle is the passenger compartment, and the started with the charging connector charging performance may degrade, incorrectly inserted.
Page 82
Verify that there is a charging system fault message on the instrument cluster, then stop the Vehicle display fails. charging. It is recommended to contact a BYD authorized dealer or service provider. Charging will automatically restart when the AC grid outage power grid is restored.
Function Vehicle Status Indicator Status Color Charge port opened (no Lighting Solid white connector connected) Charge/discharge initialization Flashing yellow process Charging Charging being scheduled/ Solid yellow charging paused Charging in progress Flashing green Charging Charging complete Solid green Dischargin Discharging in progress Flashing blue Fault Charge/Discharge fault...
Page 84
It is recommended to contact a The highest working temperature ● ● BYD authorized dealer or service allowed for the product is 50°C. provider or local electrician to Store the product in a cool and select an appropriate power dry place when it is not in use.
Page 85
At this point, you can schedule ● charging on the infotainment touchscreen. See for the configuration process. 3. Stopping charging End the charging: ● The charging automatically ends ● when the vehicle is fully charged. To end the charging early, proceed to ●...
Page 86
Use a standard-compliant household ● WARNING charging box. For how to use the charging equipment, refer to its user If the charging connector cannot ● manual and follow the operating be removed after unlocking, try a steps. few more unlocking attempts. If that does not work, try emergency The single-phase AC charging box ●...
Page 87
Charging ends automatically when ● early stop time is due or charging is complete. Unplug the charging connector: ● Disconnect as per the instructions for ● mode 2 charging. Close the AC charge port door (see ● instructions for Mode 2 charging). Store the equipment properly.
Page 88
CAUTION Setting screen The reservation charging function ● ① Reservation charging switch is developed for BYD's slow AC charging equipment only. Please ② Charging start and end time disable this function when using slow AC charging equipment that ③ Repeat cycle is not certified by BYD.
Page 89
REMINDER REMINDER The instant charging option on function may be activated, which ● the reminder screen is valid for is normal and not a vehicle failure. the current reservation only. To Power for intelligent charging cancel all reservations, toggle ● comes from the high-voltage charging reservation off...
In the event of abnormality ● or function failure, contact a When the charging connector cannot be BYD authorized dealer or service unplugged due to failure of the anti-theft provider. lock, unlock the charge port manually and unplug the charging connector.
Page 91
CAUTION WARNING Do not touch any metal terminal please refer to the precautions for ● charging equipment in of the discharge power strip, in-vehicle discharge socket, or Before discharging, please vehicle charge port during ● confirm the vehicle SOC and discharging.
Connect the V2L discharge device When the vehicle is powered off and ● ● to the charge port. The power strip then on, the display mode set last indicator lights up when the strip is time will be maintained. powered and ready for use. REMINDER Discharging starts: ●...
Page 93
It is normal that vehicle performance When the high-voltage battery is ● ● is affected by battery electrochemical normal, the driving range of the vehicle properties and self-protection and varies with the following factors: varies to some extent in the following Driving habit: For example, the conditions: ●...
Page 94
● sources and direct sunlight can the instrument cluster. In that case, reduce the service life of the high- it is recommended to contact a BYD voltage battery. authorized dealer or service provider. If there is a collision with When the battery SOC increases ●...
How to scrap an NEV: battery. Therefore, it is normal that the 1. Take the vehicle to the BYD recycling SOC or the pure-electric driving range service provider that will assess the displayed on the instrument cluster...
Usage Precautions BYD does not provide free warranty for ● the damage or faults resulted from the trailer towing. Break-in Period Saving Energy and Extending Vehicle Service If the powertrain is hard to start or ● frequently stops turning, inspect the Life vehicle immediately.
Keep moderate speeds in motorways. remains within the specified maximum ● The higher the speed, the higher weight. the consumption. Maintaining vehicle speed within the economical speed WARNING range can save power. Overloading and improper ● 3. Reducing load: accommodation may affect stability and vehicle control, Consumption is higher when air ●...
Page 98
flooded areas. For trunk strapping or fastening The motor will be seriously ● ● supplies, contact a BYD authorized damaged if it is submerged when dealer or service provider. crossing a flooded area. Such damaged is not covered by the...
● signs, such as abnormal noises and fire. odors in the vehicle body. When It is recommended to go to a BYD abnormal conditions are found, turn ● authorized dealer or service provider off and stop the vehicle immediately.
hood closed can control the fire so that the fire can be easily put out). Point the on-board fire extinguisher at the ignition point from the hood gap to put the fire out, or seek help from the passing cars. If you can borrow more fire extinguishers, open the hood to put it out when you cannot see any flame from outside.
Page 101
Remote Start* → → New Energy → Energy Manager. Before starting Standard: When the accelerator ● 1. The power mode is "OFF". pedal is released, the motor controller recovers energy in the 2. The gearshift lever is on "P". standard level, and the vehicle 3.
BYD authorized dealer brake. Verify that the vehicle maintains or service provider for inspection. a straight direction. Exterior Other abnormalities: Check for loose ● parts, leaks, and unusual noises. Tires: Check tire pressure and ●...
CAUTION WARNING To prevent damage, press the "P" Never shift to "R" or press the ● ● button only after the vehicle has "P" button while the vehicle completely stopped. is moving, in order to prevent accidents. "R": Reverse, used only when the ●...
Page 104
CAUTION CAUTION When flashes, EPB is working. The EPB system conducts power- ● ● If the vehicle is on a slope, do not up self-check within several release the brake pedal until seconds after the vehicle is steady on. Otherwise the vehicle started.
Page 105
WARNING signal and relevant parts and lines. If it cannot be released, contact a BYD To prevent the vehicle from ● authorized dealer or service provider moving, do not the replace EPB immediately.
CAUTION WARNING AVH mode even if the AVH standby When the EPB switch is pulled ● or released, the brake pedal conditions are not met. must be pressed to prevent the vehicle from moving, and AVH Standby Preconditions (All Must Be the subsequent locking of the Met) gearshift that occurs because...
Drive carefully on slippery roads, such ● CAUTION as roads covered in ice, snow or sand, or surfaces such as wet ceramic tiles or For AVH to be activated, all ● epoxy resin. Avoid parking on slopes to conditions of automatic parking prevent vehicle sliding.
4. Use anti-freeze washer fluid. Cruise speed and time interval from ● These can be found in the BYD the vehicle ahead can be set by ● authorized dealer or service provider using the cruise buttons. Cruise control and the auto parts stores.
Page 109
manually activated. If the vehicle Brake pedal is pressed at speed 0; or ● does not meet activation conditions, brake pedal is not pressed at speeds it must be checked until such above 0. conditions are met. At this time, There is no vehicle network ●...
Page 110
While ACC is active, pressing button If the vehicle stops for more than three ● ● ① for a second time or pressing the minutes, the ACC system will enter brake pedal makes the ACC system go standby mode, with EPB engaged. on standby.
Page 111
collision and requires the driver to the driver. The system cannot give beware of the surroundings. audible or visual warnings in every case. The ACC system cannot identify ● pedestrians or oncoming vehicles. A short distance from an adjacent lane ●...
Page 112
(covered in ice/snow or flooded). necessary. Make sure to go to a BYD ● Longitudinal assistance, driven by the authorized dealer or service provider ●...
Page 113
only when the vehicle is in Park.) indicator lights up on the When the vehicle is just started up, ICC status before the last power-off is instrument cluster. maintained. ICC Activation Conditions The EPB has been released. Precautions ● ICC integrates ACC and LCC. Therefore, The vehicle is in Drive.
Page 114
Situations where ICC cannot be used How to Use ● include: Enable or disable the PCW and AEB ● in infotainment touchscreen → → The sensor is blocked. ● ADAS → Active Safety. By default, the The vehicle is running under severe ●...
Page 115
it is approaching a stationary target, Pedestrians or vehicles move too ● vehicle speed is between 4 km/h and quickly into the sensor's detection 60 km/h. range. The EPB is released. Pedestrians are obscured by other ● ● objects. The vehicle is in Drive. ●...
Page 116
Use of a small spare tire or tire repair and effective control of the vehicle ● kit. under dangerous conditions. Make sure to go to a BYD The system cannot completely protect ● ● authorized dealer or service provider pedestrians or avoid accidents and for professional calibration of the severe injuries on its own.
Page 117
ACC system performance has When FCTB is activated, flashes ● ● degraded or become abnormal. together with a prompt message on Do not attempt to test the PEB system the instrument cluster. ● on your own using objects such as In the event of FCTA/FCTB malfunction, carton, iron plate, dummy, etc.
Page 118
BSD radar sensor calibration can accordance with the sign) is displayed degrade system performance. If this on the instrument cluster. is detected, contact a BYD authorized dealer or service provider. When TSR is enabled but unable to ● identify traffic signs,...
Page 119
In case there is a collision or the ● camera sensor has been reassembled, Precautions it is recommended to go to a BYD authorized dealer or service provider ISLC integrates ACC and TSR. ● for sensor calibration so as to avoid Therefore, ACC and TSR function affecting system performance.
Page 120
use (see the previous chapters for With the function enabled, when the ● details). light switch is on "Auto", the light meets conditions, and vehicle speed The intelligent cruise control system ● exceeds 35 km/h, is displayed on is a driving assistance system, so the the instrument cluster.
Page 121
If LDP system is activated, it gives sensor has been reassembled, it ● alarms to the driver (in the form is recommended to go to a BYD of audible alarm, visual alarm, and authorized dealer or service provider steering wheel vibration) and the...
Page 122
If it does when the vehicle is entering or not, it is recommended to contact exiting a tunnel. a BYD authorized dealer or service Lane lines obscured by tree shadows provider. ● on roads in direct sunlight on sunny Disabling the LDW is recommended days.
Page 123
Situations where lane lines may not be system to provide reverse torque, keeping ● identified include, but are not limited the vehicle in the current lane. How to Use Unclear lane lines ● Incomplete lane lines. To enable or disable ESA, go to ●...
The vehicle encounters certain metal lights flash to alert the driver, reducing ● guardrails or similar road conditions. the possibility of collision. RCW* WARNING At vehicle speeds above 5 km/h, if ● ESA only serves as a driving radar sensors detect a risk of collision ●...
Page 125
BSD radar sensor calibration can condition. For example, if they are degrade system performance. If this covered in dirt, snow or other is detected, contact a BYD authorized obstructions, they need to be cleared dealer or service provider. right away...
Whirling Adjusting: Used to adjust the ● WARNING angle of HUD virtual image to -2°, -1.6°, -1.2°, -0.8°, -0.4°, 0°, 0.4°, 0.8°, Use blind spot assist based on ● 1.2°, 1.6°, or 2°. The default value is your needs, traffic, and road 0°.
Page 127
In this alarm persists for a long time, please case, the vehicle may be out contact a BYD authorized dealer or of control. If there is a flat tire service provider. and monitoring fails to inform,...
AVAS spare tires* or tire rotations. has two sound sources: standard and Please go to a BYD authorized brand. To choose a sound source, go dealer or service provider to re- to infotainment touchscreen →...
When the radar that there is no sound, contact a display is enabled, an obstacle warning BYD authorized dealer or service is displayed as it is approached. provider to deal with it. Slowly tap the body image on the left ●...
WARNING WARNING on the display screen may After the vehicle is powered on, ● appear somewhat deformed in if you press the panoramic view comparison with the actual start button or shift into reverse object. while the infotainment system is not fully activated, the output on The panoramic view system is the panoramic view screen will...
Page 131
Sensor Type ⑧ Rear right sensor When the sensor detects an obstacle, ● an image is displayed on the infotainment touchscreen* according to the location of the obstacle and its distance from the vehicle. When the driver conducts parallel ● parking or reverse parking, the sensor measures the distance between the vehicle and the obstacle...
Page 132
Approximate Distance Touchscreen Display Alarm Sound (mm) Example About 300 to 600 Fast About 0 to 300 Continuous Working Sensors and Detection Range REMINDER All sensors are activated upon reversing. In some cases, the system cannot ● operate properly and will fail The illustration shows the sensors' to detect certain objects as detection range.
If the issue and vehicle speed, and continuously persists, go to a BYD authorized dealer compares it with the actual condition. or service provider for inspection. If the vehicle deviates from the normal...
Page 134
Traction Control System(TCS) Intelligent power braking system has the following new functions compared with TCS prevents the drive wheels from the original ESC system: skidding during acceleration by reducing the motor power, and, when necessary, Brake assist mode ● applies braking forces to prevent drive The brake assist mode is used wheels from spinning.
Page 135
As long as the system detects rain ● or the wiper ON signal, the brake discs are repeatedly wiped at certain intervals to improve safety. ESC working ● If there is a risk of skidding or ● backsliding when the vehicle starts on a slope, or if either drive wheel is idling, the ESC indicator flashes to indicate that ESC system is working.
Page 136
BYD authorized dealer or service provider. Tire and suspension handling ● The use of any defective tire or ● modified suspension affects the driving safety system and may cause the system to fail. Active Suspension Mode* When the front tires skid, there is The active suspension mode function ●...
Functions park the vehicle in a safe place. It is recommended to contact a BYD authorized dealer or service provider. Interior Rearview Mirror In this case, if brakes are applied, ●...
WARNING driving. This may distract your attention, causing accidents. Do not hang heavy objects from ● the interior rearview mirror, or shake or drag it with force. When manually adjusting the ● interior rearview mirror, do not forcibly adjust the stuck mirror to avoid the mirror falling off.
Replacing Wiper Blades With the ignition on, turn on the wiper service function by going to infotainment touchscreen → Vehicle Health → Overhaul. When the corresponding wiper service function is enabled, the wipers rotate out automatically for easy maintenance and replacement. 1.
Page 140
Before purchasing and installing snow ● chains, consult a BYD authorized dealer or service provider where your vehicle was purchased. After snow chains are installed, be sure ● to travel at a speed below 30 km/h on snow-covered roads.
Page 142
IN-VEHICLE DEVICES Infotainment System...... 142 A/C System........144 BYD App...........152 Storage..........153 Other Devices........155...
Infotainment During the process, do not touch any ● infotainment button or turn off the System power supply, or errors may occur. The process takes two to five ● minutes. Infotainment Touchscreen WARNING When the ignition is switched on, the Do not use a high-power inverter initial screen is displayed for several ●...
The touchscreen interface shown ● here is for reference only. BYD Assistant Navigation Bar BYD Assistant is an intelligent voice assistant that responds to your : returns to the previous page or exits voice commands, such as requesting navigation, playing music/radio, making the program.
phone is consistent with the code on Delete the touchscreen. Touch and hold any file, select files, ● 4. Set Bluetooth when connection is and then tap Delete. complete. Sort Bluetooth Call Files are sorted by name by default. ● Go to the dialing screen when Bluetooth You can also sort them by size, type, or is connected.
Page 146
Tap this button to set the time for ● remote A/C running. Auto A/C mode Two options are available: Economical ● and Comfort. Automatic purification Tap this button to enable auto ● purification function. Auto air recirculation when parking Tap this button a second time to Tap this button to enable this setting.
Circulation mode A/C operation interface Ventilator A/C ON/OFF Front passenger's temperature Auto mode control Cooling Driver's temperature control Max cooling Air distribution Independent control Fan speed control Rear control panel interface* Automatic screen lock REMINDER With the rear screen lock released, ●...
Page 148
A/C ON/OFF Tap this button to activate A/C ● ventilation control. The outlet air is Tap this button to disable the A/C if it is natural air. ● Tap this button again to exit. ● Tap this button to enable the A/C if it is ●...
Page 149
to exhaust hot air and speed up A/C REMINDER cooling. defrost button when it is not To speed up cooling, adjust the ● needed. temperature to "Lo" and use the recirculation mode for a few minutes. Fan speed control Make sure that the air intake grille in ●...
Page 150
If the odor persists after odor ● prevention methods are used, it is recommended to contact a BYD authorized dealer or service provider for repair. In order to reduce odors from ● the A/C, if the A/C is already...
is turned on, the system thoroughly removes PM2.5 particles from the air blown into the cabin. Air purification operation interface On the infotainment touchscreen, tap Air purification. The air purification interface is displayed. Air Purification System The air purification system purifies airborne PM2.5 particles.
Page 152
Cloud Service App* following environments: Sandstorms and other such ● extremely harsh environments. Turning on the A/C: On the BYD app, ● tap A/C ON, adjust "Set temperature", Cold regions (with ambient ● "Duration" and "Circulation mode", temperature below -20°C).
IoV. abnormal information, driving condition, charging status, A/C status, Search for "BYD" in Google Play or App ● door and window states, seat heating Store to download and install BYD app. and ventilation states, and tire pressure.
Individual Center and Cubby Box Vehicle Management To use the cubby box, press the switch on the front of cubby box to open it. Tap "My Account" to go to the individual center. Vehicle management: changes vehicle ● name and license plate number. Account and security: recovers or ●...
Page 155
CAUTION REMINDER To ensure safe driving, the driver any liquid spilling from the cup or ● is strictly prohibited from taking can; otherwise, the USB ports may the cup out or placing it in the cup be damaged. holder while driving. Rear Seat Cup Holder Glasses Case 1.
When a vanity mirror is installed, flip ● down the sun visor and slide the mirror cover for use. Seatback Pockets There are seatback pockets at the ● back of the front seats for storing REMINDER magazines, newspapers, or similar objects.
USB Ports CAUTION Do not hang items on hooks and USB charge ports can only be used when ● grab handles while the vehicle is the ignition is on. in motion. Only charge ports are provided under ● the front cup holder cover. 12V Auxiliary Power ①...
CAUTION CAUTION Do not use substandard or format, it is required to converted ● special USB storage devices to them into FAT32 format on the avoid damaging the infotainment infotainment touchscreen after system or data in the USB device. inserting the cards. Incompatible cards may not be ●...
Page 159
If it wireless charger via the gap is still impossible to charge the around the rubber mat. phone, contact a BYD authorized Charging may stop at high dealer or service provider. ● temperatures, and will resume After power-off, if the phone is...
Page 160
If the phone wireless charger ● system is faulty and does not work properly, it is recommended to contact a BYD authorized dealer or service provider. BYD will not assume any ● responsibility for any problems caused by improper use. If the product is disassembled or modified, the free warranty will be...
Maintenance If the vehicle is operated primarily under one or more of the following special Information conditions, certain maintenance items need to be performed more frequently. Road conditions Maintenance Cycle and ● Muddy, sandy, or snowy roads. Items ● Dusty roads ●...
Page 164
Item Interval Front and rear suspensions Check every 24 months or 30,000 km Tire condition and inflation pressure, incl. Check every 24 months or 30,000 km TPMS Check during maintenance and rotate Tire wear (Check front and rear wheel when necessary; Under severe working alignment when tire uneven wear is greater conditions, check more frequently and than 2 mm)
Therefore, you are recommended to send the vehicle to a BYD authorized dealer or service provider as soon as possible: Motor start produces unusual noises. ●...
Page 166
BYD authorized dealer or service provider for repair. The vehicle must be waxed once a ●...
polished and waxed as well as painted instructions. Soak a soft cloth with finish. cleaning solution and gently wipe it down along the direction of the water flow. Do not wipe in a circular motion CAUTION or horizontally. When the vehicle is repainted ●...
Carpet REMINDER Clean carpets with a good foam ● easily damaged by organic matter. detergent. If any organic matter splashes on the vehicle trim, remove it Use a vacuum cleaner to remove as ● with water and check whether much dust as possible. Several types the trim is damaged.
Page 169
For any questions about vehicle ● CAUTION cleaning, please consult a local BYD authorized dealer or service provider. When cleaning the inside of the ● rear windows, take care not to CAUTION scratch or damage electric heating wires or junctions.
Strictly prevents chemicals (perfume, ● CAUTION alcohol, cosmetics, tea, mineral water, grease, etc.) from contaminating real Beware of short circuits, as some ● wood trims. These chemicals could circuits and vehicle components lead to cracking or bonding gap of real carry high current or voltage.
Page 171
It is recommended to have the headlights aligned by a BYD Brake fluid level - Check the level authorized dealer or service provider. ●...
In addition, do not open the recommended to drive the vehicle sunroof when it rains or the vehicle is to a BYD authorized dealer or being washed. service provider for maintenance. Clean the front of rear glass (with the ●...
(preferably once every month). If the is fully locked and closed. Keep your vehicle has been parked for a year or hands at a certain distance and do not more, go to a BYD authorized dealer press the ridges. or service provider for comprehensive maintenance.
It is recommended to go to a removal and prevent freezing in cold ● BYD authorized dealer or service weather. provider for adding the coolant. Braking System Check the level in the fluid tank ●...
Page 175
If A/C cooling efficiency decreases, go jet. ● to a BYD authorized dealer or service provider for maintenance. Maintenance Rules CAUTION Clean windshield and blade regularly ●...
Page 176
Promptly clean mud and insect maneuverability, tread life, and driving ● carcasses stuck to the windshield with comfort. a rag. Under-inflated tires can cause uneven ● When there are marks on the tire wear, affect steerability and energy ● windshield caused by gravel, consumption, and are prone to leakage maintenance must be carried out due to overheating.
Page 177
Replace the tire if bumps, or tread (above 80 km/h), but not at low ● or side damage are found. Tires speeds, go to a BYD authorized dealer should be replaced if any of the cases or service provider and check the tires. happens.
Page 178
● ● used for the vehicle. maneuverability and stability of the vehicle, and may lead to accidents. After tire replacement, go to a BYD ● authorized dealer or service provider Do not replace only one tire; ● for tire pressure matching.
Page 179
hood, dashboard, and rear compartment end panel of the dashboard and then PDBs. showing the correspondence of the lower panel of the dashboard. fuses with electrical components. The rear compartment PDB is located ● ① Under-hood PDB in the rear section of left-side C-pillar trim.
Page 180
Under-Hood PDB Nameplate WARNING BYD authorized dealer or service provider. Fuses Protected Component or Ampere (A) Circuit Dashboard PDB...
Page 181
Protected Component or Ampere (A) Circuit Charging and distribution assembly Left combination headlight Right combination headlight Battery manager Front motor controller Rear motor controller Brake light switch Rear defroster Front wiper VTOV Electrically controlled cooling water pump 2 Electrically controlled cooling water pump Compressor Auxiliary power...
Page 182
Protected Component or Ampere (A) Circuit Battery manager Steering wheel heater Rear body control module Gearshift panel ADAS Instrument Cluster Blower Integrated thermal management module ADAS 70 / 100 C-EPS/R-EPS Electric fan Battery...
Page 183
Dashboard PDB Nameplate Protected Component or Ampere (A) Circuit Rear body control module Front left window Front right window...
Page 184
Protected Component or Ampere (A) Circuit Gearshift panel Infotainment system Panel ambient light Combination switch Wireless charger Diagnosis port Instrument Cluster Smart access Vehicle controller Front left power seat Front right power seat...
Page 185
Rear Compartment PDB Nameplate* Fuses Protected Component or Ampere (A) Circuit Front left pre-tensioner motor Front right pre-tensioner motor Rear left power seat Rear right seat High-frequency receiving module Suspension module Rear body control module Rear body control module...
Page 186
Protected Component or Ampere (A) Circuit Left combination tail light Right combination tail light External amplifier External amplifier ADAS External amplifier Left rear window Right rear window On-board charger UWB*...
Page 187
Protected Component or Ampere (A) Circuit...
Page 188
WHEN FAULTS OCCUR When Faults Occur......188...
Page 189
In that case, it is recommended to contact a BYD authorized service provider as soon as possible to change the battery, and you can start the vehicle in no-power mode.
Page 190
1. Switch the ignition off, and disconnect off immediately even if the ignition is the low-voltage battery if conditions switched on. Contact a BYD authorized permit. dealer or service provider as soon as 2. It is recommended to call immediately possible.
Page 191
If any repair is CAUTION required, it is recommended to go to a BYD authorized dealer or When moving the vehicle on a ● service provider for repair. flatbed device, make sure that the...
Page 192
force. Dragging the vehicle from the side or vertically is prohibited. The towed vehicle must be ● controlled by a driver inside the cabin, with the steering and braking systems in normal conditions. WARNING Never rescue a stuck or high- ●...
Page 193
To prevent slipping, secure the vehicle ● REMINDER by wedging the tire diagonally against the flat tire. triangle side facing oncoming vehicles, 100-200 meters away CAUTION from the vehicle. After the repair, recover the warning triangle for Do not continue driving with a ●...
Page 194
figure), turn off accident, rinse mouth thoroughly the inflator. You are recommended to and drink plenty of water contact a BYD authorized dealer or immediately. Do not induce service provider. vomiting, but seek medical attention immediately.
If the tire pressure does not reach ● 130 kPa (1.3 bar), contact a BYD authorized dealer or service provider. REMINDER Using tire repair kit on damaged ●...
Page 196
3. Turn the rocker wrench WARNING counterclockwise to loosen all lug nuts of the deflated tire. When you jack up the vehicle, observe the following rules to reduce the likelihood of injury: When you jack up the vehicle, do ● not have any part of your body under the vehicle.
Page 197
Installing a spare tire requires more Before installing the wheel, remove ● ● distance from the ground than corrosion from the mounting surface removing a deflated one. with a wire brush or the like. CAUTION When you install a wheel, ensure ●...
Page 198
Be sure to mount the tire valve cap; ● REMINDER otherwise dust and moisture will enter the valve stem and cause air leakage. If Tighten the nuts with a rocker the valve cap is lost, use a new one as ●...
Vehicle Data Vehicle Data Dimensions: Item Parameter Length * Width * Height (mm) 4995*1910*1495 (side mirrors not included in width) Wheelbase (mm) 2920 Front track (mm) 1640 Rear track (mm) 1640 Front overhang (mm) Rear overhang (mm) 1100 Approach angle (°) ≥13 Departure angle (°) ≥14...
Page 202
Drive type Front: 65/4400/140 Rated power/speed/torque (kW/rpm/Nm) Rear: 65/4775/103 Front: 180/15000/350 Peak power/speed/torque (kW/rpm/Nm) Rear: 200/15000/350 Vehicle power and economy: Item Parameter Max. design speed (km/h) Max. gradeability (%) ≥50 Power consumption per 100 km under comprehensive working conditions 18.8 (WLTC) (kWh/100 km) Wheels and tires: Item...
Page 203
Front brake disc thickness (mm) Rear brake disc thickness (mm) Front friction plate thickness (mm) Rear friction plate thickness (mm) High-voltage battery: Item Parameter Type Lithium iron phosphate battery High-voltage battery rated capacity (AH) Seats: Seats Item Parameter Forward and backward moving spaces for front 30 mm forward from the seat (seat cushion depth...
A/C refrigerant R1234yf 1150±20 g Information VIN is engraved on the lower beam of the front passenger seat. Vehicle Identification ① VIN attached on the front of transmission assembly housing ② VIN attached on the side of the hood ③ VIN attached on the front windshield cross sill ④...
The airbag warning label is printed on the right sun visor. Warning Labels The tire pressure label is attached on the ① A/C system and cooling fan sticker lower part of the left B-pillar. ② Battery location sticker The AC charging warning label is attached on the inner side of the charge port door.
The vehicle has different types of radio equipment. The manufacturers of the radio equipment declare that the RF Modules are in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following Internet address: https://cn- prod.byd.com/eu/eu-doc.
Page 208
Driving........... Driving Precautions...... A/C Operation Interface....Driving Safety Systems....A/C Settings Interface....A/C System Maintenance....A/C Vents........About BYD App......Account Registration....Electronic Child Protection Lock..Acoustic Vehicle Alerting System Electronic Smart Key...... (AVAS)..........Emergency Shutdown System..Adaptive Cruise Control (ACC)*..
Page 209
If a Collision Occurs...... Navigation Bar......If a Fire Occurs....... If a Tire Goes Flat......If Smart Key Battery Is Exhausted If the High-Voltage Battery Leaks. Odometer Switch......If the Vehicle Needs Towing..Indicators/Warning Lights....Opening and Closing the Hood..Individual Center and Vehicle Management.........
Page 210
Switching on A/C with Cloud Service App..........Tire Pressure Monitoring....Tires..........Traffic Sign Recognition (TSR)..Trailer Towing......... USB Ports*........Using Seat Belts......Vehicle Cleaning......Vehicle Corrosion Prevention..Vehicle Identification Number..Vehicle Servicing......Vehicle Storage Precautions..Wading into Water......Warning Labels......Washer...........
Page 212
Abbreviations Abbreviations Termin Termin Name Name ology ology Electronic Control Unit Event Data Recorder Ecology, Conservation, SPORT Sport Optimization NORM Normal E-Call Emergency Call Electronic Parking Brake Auto Vehicle Hold Adaptive Cruise Control Pedestrian Collision Warning Automatic Emergency Braking Lane Departure Warning Lane Departure Prevention TPMS Tire Pressure Monitoring System...
Need help?
Do you have a question about the HAN EV 2024 and is the answer not in the manual?
Questions and answers