Subscribe to Our Youtube Channel
Related Manuals for Lockly Pro LOCKLY GUARD DUO 679D
Summary of Contents for Lockly Pro LOCKLY GUARD DUO 679D
- Page 1 INSTALLATION GUIDE 679D INTERCONNECTED EDITION For commercial use & professional installation www.LocklyPRO.com...
- Page 2 GET THE MOST OUT OF YOUR LOCKLY GUARD ™ Get the latest user/installation manuals , instructional videos, and FAQs SCAN or VISIT Locklypro.com/679D...
- Page 3 Welcome! This guide will walk you through step-by-step how to install and get Lockly Guard up and running. Installation generally ™ takes less than 30 minutes. If you have any questions please call our VIP Hotline (855) 562-5599 for help. Reference installation parts overview foldout on back page...
- Page 4 Preparation To complete the installation you will need: Phillips Screwdriver Flathead Screwdriver Tape measure or ruler Optional Pliers Screwdriver with drill bits Drilling maybe required to install this lock. If you are installing your lock on a brand new door, a drill is required if there are no holes prepared for lock installation.
-
Page 5: Important Notice
Preparation continued Remove existing door hardware, latch or deadbolts before installing the new lock. Use provided template to bore new holes if needed. Measure and confirm 1- 3/8"—2" your door is between (35mm—50mm) 1-3/8" - 2" ( 35mm - 2-1/8" 50mm). - Page 6 Step 1 INSTALLING THE LOCKSET Measure the distance between center of front door hole to the edge of your door hole to determine the backset. Adjust latchbolt and deadbolt according to the backset of your door. Deadbolt Adjustment 2-3/8"(60mm) 2-3/4"(70mm) extend I.
- Page 7 Step 1 INSTALLING THE LOCKSET continued After adjusting the latchbolt , determine the orientation of the latchbolt. Determine the orientation of latchbolt. Facing the door exterior, install the latchbolt according to the opening direction of your door. LEFT OUT-SWING DOOR RIGHT OUT-SWING DOOR Inside Inside...
- Page 8 Step 2 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS The lock ships with handle default for right in-swing or left out-swing door. Check the diagram below if you are unsure of you door orientation. RIGHT IN-SWING DOOR INTERIOR LEFT IN-SWING DOOR Hinge Side LEFT OUT-SWING DOOR...
- Page 9 Step 2 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS continued Rotate the handle 180° to the other Confirm that your installation was side of the lock. complete by checking if the pins are flush against the handle, and Using your fingers, press the two pins has popped out.
- Page 10 Step 2 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS continued At the back of the exterior panel, remove the screw on point "R". Align the screw hole on point "L" then insert the removed screw and tighten.
- Page 11 Step 2 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS continued Changing the Interior Handle Orientation Remove the handle retaining screw and detach the handle. Rotate it to 180° then return as shown. Insert the handle retaining screw and tighten using a screw driver.
- Page 12 Step 3 PREPARING LOCK FOR INSTALLATION Carefully prepare the lock and ensure the required parts ( ) have been properly attached before installing to door. Slotted Barrel Extension E should be installed accord- ing to upper door hole distance to the bottom door hole (4"...
- Page 13 Step 4 INSTALLING THE LOCK (EXTERIOR) Ensure is securely installed on the correct Exterior position, then insert to top door hole, passing through below part While aligning the lock straight up-and-down, pass the wiring cable under the latchbolt then ensure the Slotted Barrel Extension passes through the hole on the lower part of the deadbolt...
- Page 14 Step 5 INSTALLING THE LOCK (INTERIOR) Select interior cover plate according to door hole distance and install on to door. 4” use cover plate 5.5” use cover plate Ensure the rods on interior cover plate is inserted on the holes of the deadbolt.
- Page 15 Step 5 INSTALLING THE LOCK (INTERIOR) continued Secure interior cover plate with screws , then remove the positioning tool . Check and ensure the spindle is at the center after removing Hole for screw for 5.5" Secure with Hole for screw for 4"...
- Page 16 Step 5 INSTALLING THE LOCK (INTERIOR) continued Select the side of the interconnection gear according to door handle orientation Left or Right . Insert torque blade to plate according the distance between the latchbolt and deadbolt . Select the correct side of the interconnection gear.
- Page 17 Step 5 INSTALLING THE LOCK (INTERIOR) continued Install plate onto door. Ensure the torque blade is inserted horizon- tally to the deadbolt. The spindle must pass through the plate. Secure the plate with screws...
- Page 18 Step 6 INSTALLING THE LOCK INTERIOR (N) Make sure the cable is away and not tangling Secure the lock interior with 3 screws with the spindle Plug the cable into the interior side of Align the spindle to the lock interior the lock making sure you match the and attach the Interior lock to the orientation of the plug by matching...
- Page 19 Step 6 INSTALLING THE LOCK INTERIOR (N) continued Insert 4 AA batteries into the lock Secure the battery by sliding the by aligning the positive (+) and cover over the lock and negative (-) orientation markings turning the screw clockwise on on the batteries to the battery top until tight.
- Page 20 Step 7 PREPARING DOOR SENSOR FOR INSTALLATION Do not mount (install) door sensors yet. You will install in step 9. About door sensors Door sensors provide real-time door condition status, such as the ability to verify if the door is securely closed. It also sends push notifications to your phone whenever your door opens and enables voice control.
- Page 21 Step 7 PREPARING DOOR SENSORS FOR INSTALLATION continued When you are installing the door sensors, make sure the arrow of the wired sensor is placed next to the arrow of the sensor magnet as close as possible. LEFT RIGHT IMPORTANT: Do not install the sensorclose to the strike plate 2-3/8"...
- Page 22 Step 7 PREPARING DOOR SENSORS FOR INSTALLATION continued The interior assembly comes with the pre-installed wired door sensor setup for a right/left swing doors with 2-3/4" (70mm) backset*. Trim excess part for doors with 2-3/8" (60mm) backset as shown below. Trim excess here for 2 ⅜"...
- Page 23 Step 8 INSTALLING THE DOOR STRIKE It is recommended that you use the included strike plate. However, if you find the deadbolt and latchbolt works with your existing strike plate free of any binding or resistance you can use it. Regardless of which strike plate used, deadbolt and latchbolt needs to operate smoothly, free of any binding or resistance.
- Page 24 Step 9 INSTALLING THE DOORS SENSOR Make sure you have prepared the door sensors for installation according to Step 7 Peel off the paper layer of the Position the wired sensor adhesives from the back of the the edge of the door, avoiding wired sensor the door strike plate.
- Page 25 Step 10 DOWNLOAD LOCKLYPRO APP Congratulations! You have completed the Lockly Guard™ Duo (679D) physical lock installation. To complete your setup, download the LocklyPro app from the iOS or Google Play app Store and follow on-screen instructions. Scan or visit Locklypro.com/app...
- Page 26 Step 11 SETTING UP THE SECURE LINK WI-FI HUB To set up your Lockly Guard™ Duo (679D), choose an appropriate location for the Secure Link Wi-fi Hub for optimum performance (see below). For optimum connectivity, it is recommended that the hub be no further away from the lock than 30 feet (9 meters).
- Page 27 Step 11 SECURE LINK WI-FI HUB SETUP continued Plug the Secure Link Wi-Fi Hub into the 5V 1A USB AC adapter and plug the AC adapter to your wall socket. GREEN LED indicator light will flash slowly to indicate that the Wi-Fi Hub is ready to connect.
-
Page 28: Add New Device
Step 12 CONNECTING YOUR LOCKLY GUARD DUO (679D) ™ The App will take you through the following steps, make sure the smart lock has been properly installed. You will need your activation card that is included in the box to proceed. ADD NEW DEVICE Select A Device 9:41 AM... - Page 29 Step 12 CONNECTING YOUR LOCKLY GUARD™ DUO (679D) continued If you can't scan LOCK SERIAL, Scanning LOCK SERIAL Input Activation Code Then enter manually 9:43 AM 100% ●●●●● AT&T 9:44 AM 100% 9:44 AM 100% ●●●●● AT&T ●●●●● AT&T KEEP THIS CARD! ACTIVATION CARD LOCK SERIAL PGDxxxxxxxxxx...
- Page 30 Step 12 CONNECTING YOUR LOCKLY GUARD™ DUO (679D) continued Plug in your Secure Link Password setting OK and Click "YES" Set Wi-Fi ●●●●● AT&T 9:46 AM 100% 9:47 AM 100% ●●●●● AT&T 9:46 AM 100% ●●●●● AT&T Click “Yes” when the Successfully Added green light is on 9:48 AM...
- Page 31 FCC Warning： This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
- Page 32 L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: 1. L’appareil ne doit pas produire de brouillage; 2.
- Page 33 This lock can be installed for both right swing and left swing doors. The lock ships ready for a right swing door installation. If you wish to change the orientation of the lock for a INSTALLATION OVERVIEW & PARTS LIST Left Swing door, follow instructions on Installation Guide (Step 2).
-
Page 34: Important Notes
WAIT. IMPORTANT NOTES Lockly Guard installs differently from other door locks. Professional installer(s) and locksmiths must read and follow Lockly Guard installation and user manuals to prevent damaging the product. Failure to do so may also result in the smart lock not responding correctly to lock and unlocking commands and will require re-installation. - Page 35 For digital versions and instructional videos, please visit the following link: LocklyPro.com/support TOTAL ACCESS SOLUTION For additional support, visit http:// LocklyPro.com/support or email prosales@lockly.com © Copyright 2022 Lockly All rights reserved USA Patent NO. US 9,881,146 B2 | USA Patent NO. US 9,853,815 B2 | USA Patent NO.
Need help?
Do you have a question about the LOCKLY GUARD DUO 679D and is the answer not in the manual?
Questions and answers