Related Manuals for Lockly Pro LOCKLY GUARD DEFENDER238LE
Summary of Contents for Lockly Pro LOCKLY GUARD DEFENDER238LE
- Page 1 INSTALLATION GUIDE DEFENDER 238LE EXIT TRIM EDITION For commercial use & professional installation www.LocklyPRO.com...
- Page 2 Preparation To complete the installation you will need: Phillips Screwdriver Flathead Screwdriver Tape measure or ruler Optional Screwdriver with drill bits Pliers Drilling maybe required to install this lock. If you are installing your lock on a brand new door, a drill and door hole saw may be required if there are no holes prepared for lock installation.
- Page 3 Preparation PGD238LE is compatible with the following Push Bar Devices. • VON DUPRIN 98/99/98-F/99-F EO, DT Rim Push Bar Devices. • VON DUPRIN 98/9957/57-F EO, DT Series 3 Point Latching Push Bar Devices. • VON DUPRIN 9827/9927/9827-F/9927-F EO & DT Series Vertical Rod Push Bar Devices. •...
- Page 4 Preparation Included in the package is a borehole drilling template for Mortise Push Bar Device or Latch Push Bar Device. Please select the corresponding drilling template to bore new holes based on your door type. For Mortise Push Bar Devices For Latch Push Bar Device Measure door and drill hole using Measure door and drill hole using...
- Page 5 Step 1 DETERMINE DOOR OPENING DIRECTION There are 4 common door opening directions, the lockset configuration as shown on each diagram below corresponds to the respective door opening direction. LEFT OUT-SWING DOOR RIGHT OUT-SWING DOOR Make sure the latch throw is Make sure the latch throw is correctly oriented as shown correctly oriented as shown...
- Page 6 Step 1 DETERMINE DOOR OPENING DIRECTION continued The lock ships with handle default for right in-swing or left out-swing door. Check the diagram below if you are unsure of you door orientation. RIGHT IN-SWING DOOR INTERIOR LEFT IN-SWING DOOR Hinge Side LEFT OUT-SWING DOOR EXTERIOR...
- Page 7 Step 2 CHANGE HANDLE DIRECTION The diagram below shows how to shift the door handle from right to left direction. The default setting of the handle is for right swing door. You do not need to change direction if you have a right swing door. Change the handle direction of the Exterior Assembly Use an Allen wrench to loosen screws on both sides of the handle.
-
Page 8: Prepare Lock For Installation
Step 3 PREPARE LOCK FOR INSTALLATION 1. Installing Batteries When installing the battery for the first time, use a Phillips screwdriver to loosen the screws counterclockwise. Just loosen the screw and do not remove. Slide and pull the battery cover outward to remove. Take out the battery compartment and detach from the terminal connector. - Page 9 Step 3 PREPARE LOCK FOR INSTALLATION continued Exterior Cover and Spindle accessories for Mortise Push Bar Device or Latch Push Bar Device are provided in the packaging accessories: Mortise Push Bar Device uses Exterior Cover and Spindle Latch Push Bar Device uses Exterior Cover and Cross Spindle For Mortise Push Bar Device For Latch Push Bar Device...
- Page 10 Step 4 INSTALL EXTERIOR & INTERIOR ASSEMBLIES 1. Spindle Select spindle and insert to the exterior assembly. Ensure the Spindle is trim according to the door thickness. Refer back to Step 3.2 for instructions on selection and trimming Align screw to the exterior assembly screw hole position and tighten clockwise using the Allen wrench Mortise Push Bar Device...
- Page 11 Step 4 INSTALL EXTERIOR & INTERIOR ASSEMBLIES continued 2. Push Exit Bar，Cover Plate / V1.. Install exterior cover plate on to door. Ensure the slotted barrel extensions are properly threaded through the door holes. At the same time, align the 4 holes of the Push Exit Bar with the exterior cover plate and secure them with screws.
- Page 12 Step 4 INSTALL EXTERIOR & INTERIOR ASSEMBLIES continued 3. Exterior Assembly Install the exterior assembly onto door. Make sure the spindle, cables and rods are routed correctly through the holes in the door. Secure with screw Install top and bottom mounting blocks. Bluetooth receiver connection plug must pass through the door hole.
- Page 13 Step 4 INSTALL EXTERIOR & INTERIOR ASSEMBLIES continued 4. Bluetooth Receiver, Bottom Screw Cover Connect Bluetooth receiver . Rotate plugs to tighten cable connection. Adjust the protective cover to the cable connector to make sure that it is not exposed. Adjust the position of the protective cover to connectors.
-
Page 14: Install Batteries
Step 5 INSTALL BATTERIES Open the battery compartment cover and insert 4 AA alkaline battery as shown below. Use a screwdriver to push the back screw cover up then loosen the screw (do not remove). Remove the battery cover, carefully unplug the terminals of the battery com- partment then install the batteries. - Page 15 Step 6 INSTALL TOUCHSCREEN COVER If your door lock is located in a harsh, sun-exposed area, it is highly recommended that you install the included touchscreen cover. Clean the surface of the lock's exterior assembly. Ensure it is dry and dust free. Remove the paper layer off the adhesive tape.
- Page 16 Step 7 DOWNLOAD LOCKLYPRO APP You have completed the Lockly Guard physical lock installation. To enable live monitoring and remote control, you will need to setup the included Link Plus and pair it with the Lockly Guard Exit Trim and door sensors. Before connecting Link Plus, download the LocklyPro app on your smartphone.
- Page 17 Step 8 SET UP LINK PLUS To set up Lockly Guard, choose an appropriate location for the Link Plus for optimum performance (see below). For optimum connectivity, it is recommended that the hub be no further away from the lock than 30 feet (9 meters). During the setup process position yourself between the lock and the Link Plus Wi-Fi Hub—ideally no more than 30 feet (9 meters) apart.
- Page 18 Step 9 CONNECT LOCKLY GUARD The App will take you through the following steps, make sure the smart lock has been properly installed. You will need your activation card that is included in the box to proceed. Select Lockly Guard 238LE GET STARTED ADD NEW DEVICE Select A Device...
- Page 19 Step 9 CONNECTING LOCKLY GUARD continued Plug in your Link Plus Confirm lock password Password setting OK Set the Admin Code and Click "YES" Link Plus Plug in your Link Plus Click “Yes” when the Set Wi-Fi Successfully Added green light is on Add Link Plus Congratulations! Lockly Guard is...
- Page 20 Step 10 INSTALL WIRELESS DOOR SENSOR Lockly door sensor is based on bidirectional RF433.92MHz and Lockly 2.0 proprietary encryption, providing communication reliability, stability, and better security. It is simple and very easy to install anywhere and it only uses AAA battery for long and optimal operation.
- Page 21 Step 10 INSTALL WIRELESS DOOR SENSOR continued When you are installing the Door Sensor, make sure the arrows on the Door Sensor is placed next to the arrow from the Door Frame Sensor. When installed on your door, the distance between the Door Sensor and the Door Frame Sensor must be less than 3/4”...
- Page 22 Step 10 INSTALL WIRELESS DOOR SENSOR continued Pair the Door Sensor Usually, the Door Sensor is pre-paired with the lock and you do not need to manually pair it. If you need to pair it again, follow the following steps. In the LocklyPro Commercial app, go to Settings>Remote Control/Wireless Accessories, select add New Sensor.
- Page 23 FCC Warning： This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
- Page 24 INSTALLATION OVERVIEW AND PARTS LIST 0004001 1341652 KEEP THIS CARD! ACTIVATION CARD LOCK SERIAL PGDxxxxxxxxxx ACTIVATION CODE xxxxxxxx SCAN & SAVE LOCKLYPRO.COM | HOTLINE: +1 855 562 5599 | EMAIL: PROSALES@LOCKLY.COM Parts List Labeled As Description Allen Wrench M5 (x1) Exterior Assembly Allen Wrench M4 (x1) Touchscreen Cover...
- Page 25 INSTALLATION OVERVIEW AND PARTS LIST Bluetooth Bottom Screw Mounting Block Mounting Plate Cover (x1) (x2) (x1) Cross Spindle (x1) Spindle (x1) Machine screw M4 (x1) Allen Wrench M5 (x1) Allen Wrench M4 (x1) KM5x52mm (x4) PM5x55(x4) Escutcheon Screw Escutcheon Screw Bluetooth Key (x2) Slotted Barrel...
- Page 28 For digital versions and instructional videos, please visit the following link: LocklyPro.com/support TOTAL ACCESS SOLUTION We’re here to help! prosales@lockly.com locklypro.com/support © Copyright 2024 Lockly Guard All rights reserved USA Patent No. US 9,881,146 B2 | USA Patent No. US 9,853,815 B2 | USA Patent No. US 9,875,350 B2 | USA Patent No.
Need help?
Do you have a question about the LOCKLY GUARD DEFENDER238LE and is the answer not in the manual?
Questions and answers