Subscribe to Our Youtube Channel
Related Manuals for Lockly Pro LOCKLY GUARD DEFENDER 238LM
Summary of Contents for Lockly Pro LOCKLY GUARD DEFENDER 238LM
- Page 1 INSTALLATION GUIDE DEFENDER 238L EDITION For commercial use & professional installation www.LocklyPRO.com...
- Page 2 Preparation Installation template Baseline approximately 1 meter from the ground Ø1-11/32"(34mm) Door Handle Hole...
- Page 3 Step 1 DETERMINE DOOR OPENING DIRECTION There are 4 common door opening directions, the lockset configuration as shown on each diagram below corresponds to the respective door opening direction. LEFT OUT-SWING DOOR RIGHT OUT-SWING DOOR Make sure the latch throw is Make sure the latch throw is correctly oriented as shown correctly oriented as shown...
- Page 4 Step 2 CHANGE HANDLE DIRECTION The diagram below shows how to shift the door handle from right to left direction. The default setting of the handle is for right swing door. You do not need to change direction if you have a right swing door. Change the handle direction of the Exterior Assembly Use an Allen wrench to loosen screws on both sides of the handle.
- Page 5 Step 3 INSTALLING THE LOCKSET Make sure your door is prepared for installation. If you need to drill new holes, please use the supplied template for drilling holes. Before installing the Lockset, confirm the door opening direction (Step 1) and ensure latch throw is correctly oriented to the door’s opening direction.
- Page 6 Step 3 continued INSTALLING THE LOCKSET The Lockset adapter must be installed according to the left or right door opening direction. Install it on the door exterior. If you are installing for a left door, use the lockset adapter . If you are installing for a right door, use the lockset adapter F1.
- Page 7 Step 3 INSTALLING THE LOCKSET continued An indoor lockset fitting connector/ Indoor lockset mounting joints/handles handle has been installed. are not installed. Install faceplate and secure with Install the indoor lock adapter screws. (Prepared by the customer according to the instructions Installation) Install the indoor handle (provided by the customer and installed according to the instructions)
- Page 8 Step 4 PREPARING LOCK FOR INSTALLATION When installing the battery for the first time, use a Phillips screwdriver to loosen the screws counterclockwise. Note: Just loosen the screw, and do not remove. Pull the sides outward to remove the battery cover. Take out the battery compartment, unhook the battery compartment, and install the battery.
- Page 9 Step 5 INSTALLING THE EXTERIOR AND INTERIOR ASSEMBLY Install the exterior assembly onto the door. Make sure the spindle, cables and rods are routed correctly through the holes in the door. Install top and bottom mounting blocks and secure with scews The Bluetooth antenna base should pass through the cable hole.
- Page 10 Step 5 continued INSTALLING THE EXTERIOR AND INTERIOR ASSEMBLY Install top mounting block. Remove the adhesive tape at the back of Bluetooth receiver and install under mounting block. Mount the Bluetooth Mounting Plate on the groove of the top block to secure the Bluetooth receiver. Insert Bottom Screw Cover down.
-
Page 11: Install Batteries
Step INSTALL BATTERIES Open the battery compartment cover and insert 4 AA alkaline battery as shown below. Use a screwdriver to push the back screw cover up then loosen the screw (do not remove). Remove the battery cover, carefully unplug the terminals of the battery com- partment then install the batteries. - Page 12 Step 7 INSTALLATION OF TOUCHSCREEN COVER If your door lock is located in a harsh, sun-exposed area, it is highly recommended that you install a matching touchscreen cover. Clean the surface of the lock's exterior assembly. Ensure it is dry and dust free.
- Page 13 Step 8 DOWNLOAD LOCKLYPRO You have completed the Lockly Guard physical lock installation. To enable live monitoring and voice control, you will need to setup the included Link Plus and pair it with the Lockly Guard Doorman and door sensors. Before connecting Link Plus, download the LocklyPro Commercial App on your smartphone.
- Page 14 Step 8 SETTING UP LINK PLUS continued To set up Lockly Guard, choose an appropriate location for the Link Plus for optimum performance (see below). For optimum connectivity, it is recommended that the hub be no further away from the lock than 30 feet (9 meters). During the setup process position yourself between the lock and the Secure Link Wi-Fi Hub—ideally no more than 30 feet (9 meters) apart.
- Page 15 Step 8 SETTING UP LINK PLUS continued Plug Link Plus into the 5V 1A USB AC adapter and plug the AC adapter to your wall socket. A GREEN LED indicator light will flash slowly to indicate that the Wi-Fi Hub is ready to connect.
- Page 16 Step 9 CONNECTING LOCKLY GUARD The App will take you through the following steps, make sure the smart lock has been properly installed. You will need your activation card that is included in the box to proceed. Select Lockly Guard 238LM GET STARTED ADD NEW DEVICE Select A Device...
- Page 17 Step 9 CONNECTING LOCKLY GUARD continued Plug in your Link Plus Confirm lock password Password setting OK Set the Admin Code and Click "YES" Link Plus Plug in your Link Plus Click “Yes” when the Set Wi-Fi Successfully Added green light is on Add Link Plus Congratulations! Lockly Guard is...
- Page 18 Step 10 INSTALLING THE WIRELESS DOOR SENSOR Lockly door sensor is based on bidirectional RF433.92MHz and Lockly 2.0 proprietary encryption, providing communication reliability, stability, and better security. It is simple and very easy to install anywhere and it only uses AAA battery for long and optimal operation.
- Page 19 Step 10 INSTALLING THE WIRELESS DOOR SENSOR continued When you are installing the Door Sensor, make sure the arrows on the Door Sensor is placed next to the arrow from the Door Frame Sensor. When installed on your door, the distance between the Door Sensor and the Door Frame Sensor must be less than 3/4”...
- Page 20 Step 10 INSTALLING THE WIRELESS DOOR SENSOR continued Pair the Door Sensor Usually, the Door Sensor is pre-paired with the lock and you do not need to manually pair it. If you need to pair it again, follow the following steps. In the LocklyPro Commercial app, go to Settings>Remote Control/Wireless Accessories, select add New Sensor.
- Page 21 FCC Warning： This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
- Page 22 INSTALLATION OVERVIEW AND PARTS LIST • • • ••• •• • • • • • • • • KEEP THIS CARD! ACTIVATION CARD LOCK SERIAL PGDxxxxxxxxxx ACTIVATION CODE xxxxxxxx SCAN & SAVE LOCKLYPRO.COM | HOTLINE: +1 855 562 5599 | EMAIL: PROSALES@LOCKLY.COM Parts List Labeled As Description...
- Page 23 INSTALLATION OVERVIEW AND PARTS LIST Bluetooth Bottom Screw Mounting Block Mounting Plate Cover (x1) (x2) (x1) Lockset Adapter Lockset Adapter Left (x1) Right (x1) KM5x25mm (x4) Allen Wrench (x1) Escutcheon Screw Key (x2) Bluetooth Receiver (x1)
- Page 24 For digital versions and instructional videos, please visit the following link: LocklyPro.com/support TOTAL ACCESS SOLUTION We’re here to help! prosales@lockly.com locklypro.com/support © Copyright 202 Lockly All rights reserved USA Patent No. US 9,881,146 B2 | USA Patent No. US 9,853,815 B2 | USA Patent No. US 9,875,350 B2 | USA Patent No.
Need help?
Do you have a question about the LOCKLY GUARD DEFENDER 238LM and is the answer not in the manual?
Questions and answers