UFESA SV1200 Manual

DESCRIPTION

PLEASE READ THE INSTRUCTIONS FOR USE CAREFULLY PRIOR TO USING THE PRODUCT. STORE THESE IN A SAFE PLACE FOR FUTURE REFERENCE.

1. Hanger
2. Telescopic rod
3. Fan
4. Motor unit
5. Ventilation slots
6. Timer (30 – 180 minutes)
7. Mounting flange
8. Screw (for adjusting the height)
9. Collar section
10. Nylon balloon
11. Protective accessory

BEFORE THE FIRST USE

Before using the steam iron, please ensure you read the user manual and understand all parts and features of the steam iron. Be sure to remove any packaging material and labels before using for the first time.

ASSEMBLY

Put the piece (11) on the telescopic bar and tighten the screws to the indicated height.
Plug the telescopic rod (2) into the recess on the top of the motor unit (4).
Assemble the wings of hanger with screw, place the hanger (1) onto the telescopic rod (2). When you do this, make sure that the slight bend in the hanger (1) points forwards.
Attach the nylon balloon:
Pull it over the hanger (1). When you do this, make sure that the side with the hole line points forwards.
Put the neck at the top over the collar section (9) on the hanger (1).
Pull the large elastic cord at the bottom over the mounting flange (7).
The device is disassembled in the reverse order.

Only place the device on a stable, flat, moisture-resistant and heat-resistant surface.

Hot surface! The motor unit / telescopic rod will become hot during use. You should therefore not touch it during or shortly after use.
It is essential that you follow the care labels for the textiles to be dried!
Never cover up the ventilation slots and do not insert any objects into them.

HOW TO USE

Set the height you want. To do this, open the screw (8), pull out the telescopic rod (2) and then close the screw (8) again
If you have not already done so, pull on the nylon balloon (see the "Before Initial Use" chapter, "Assembly" section).
The nylon balloon should sit immediately below the mounting flange (7) so that it can fully inflate. Pull the garment which is to be pressed over the nylon balloon and the hanger (1) and do up the buttons if necessary. Make sure that

• the collar is fitted over the collar section (9) on the hanger (1),
• any button strip is over the hole line on the nylon balloon,
• the arms of the nylon balloon fit properly in the sleeves of the garment and are not twisted or scrunched up,
• all buttons on the garment (including on the sleeves) are done up.

Insert the mains plug into an easily accessible socket.
Turn the timer (6) clockwise and set it to the length of time you want.
Once the nylon balloon has inflated, straighten out the garment and smooth it down again.

SPRAYING

When the set time elapses, the device switches off automatically. The drying / pressing process can be interrupted at any time by turning the timer (6) to the starting position.
Remove the garment from the nylon balloon and hanger (1).
Pull the mains plug out of the plug socket and allow the device to cool down completely.

MAINTENANCE AND CLEANING

Unplug the mains plug out of the plug socket and allow the device to cool down com- pletely before doing any cleaning!
Never immerse the device, the mains cable or the mains plug in water or other liquids!
Do not use any corrosive or abrasive cleaning agents or cleaning pads to clean the device. These can damage the surface.
Clean the device and the nylon balloon if necessary with a slightly damp cloth and a little mild detergent if required. Then wipe down fully with a dry cloth.
Allow all parts to dry completely before you put them away.
Store the device in a clean, dry place that is protected from sunlight and is not acces- sible to children and animals.

Troubleshooting Guide

SAFETY INSTRUCTIONS

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
If the supply cord is damaged it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

This appliance is intended only for drying textiles washed in water.

Hot surfaces. Surfaces are liable to get hot during use.

This symbol means that the product must not be covered.
This device is designed for use at a maximum altitude up to 2000m above sea level.

IMPORTANT WARNINGS

This appliance is designed for home use and should never be used for commercial or industrial use under any circumstances. Any incorrect use or improper handling of the product shall render the warranty null and void.
Prior to plugging in the product, check that your mains voltage is the same as the one indicated on the product label.
The mains connection cable must not be tangled or wrapped around the product during use.
Do not use the device, or connect and disconnect to the supply mains with the hands and / or feet wet.
Do not pull on the connection cord in order to unplug it or use it as a handle.
Product must be used on a level and stable surface.
Do not use outdoors.
Unplug the product immediately from the mains in the event of any breakdown or damage and contact an official technical support service. In order to prevent any risk of danger, do not open the device. Only qualified technical personnel from the brand's Official technical support service may carry out repairs or procedures on the device.
B&B TRENDS SL. disclaims all liability for damages that may occur to people, animals or objects, for the non-observance of these warnings.