Advertisement
Quick Links
Advertisement
Related Manuals for Ryobi REBCTA10
Summary of Contents for Ryobi REBCTA10
- Page 1 REBCTA10...
- Page 2 The brushcutter attachment is approved for use with the ■ If operating a power tool in a damp location is following RYOBI powerheads: unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of ■...
- Page 3 ■ Disconnect the plug from the power source and/ SERVICE or remove the battery pack, if detachable, from ■ Have your power tool serviced by a qualified repair the power tool before making any adjustments, person using only identical replacement parts. This changing accessories, or storing power tools.
- Page 4 ■ Always keep proper footing and operate the Blade thrust and its related hazards can be avoided by machine only when standing on the ground. Slippery taking proper precautions as given below. or unstable surfaces may cause a loss of balance or Maintain a firm grip with both hands on the machine ■...
- Page 5 ● before inspecting the product after striking a foreign ■ Charge the battery pack in a location where the ambient object temperature is between 10 °C and 38 °C. ● before leaving the product unattended ■ Store the battery pack in a location where the ambient temperature is between 0 °C and 20 °C.
- Page 6 Regulatory Compliance Mark (RCM). SYMBOLS ON THE PRODUCT Product meets applicable regulatory requirements. Safety alert SYMBOLS IN THIS MANUAL Read and understand all instructions Note before operating the product. Follow all warnings and safety instructions. Warning Wear eye, ear, and head protection. Parts or accessories sold separately Wear non-slip, heavy-duty gloves.
- Page 7 REBCTA10 Hanger cap Lock button Lower shaft Harness Harness hanger Quick-release tab Harness clip Blade protector TRI-ARC blade Safety guard Operator's manual Front handle Powerheads Know your product...
- Page 8 Always wear eye, ear and head Push the lock button and remove the hanger cap from the lower shaft. Insert the protection, non-slip heavy-duty lower shaft into the upper shaft, and push the lower shaft until the lock button clicks into place. Make sure that the blade is facing downwards, then turn the knob gloves, and substantial footwear while operating the product.
- Page 9 1/4-20UNC-2B On the front handle clamp, turn the nut Attach the clamp and the front handle to NOTE: Position the front handle only in the area where the attachment capable counterclockwise to loosen and remove the upper shaft. label is placed. the bolt, washer, and nut.
- Page 10 Operating the p.11 product Replacing the Cleaning the p.12 p.14 Storing the product p.15 TRI-ARC blade product...
- Page 11 OPERATING THE PRODUCT WARNING: Exercise extreme caution when using the product. Keep hands and feet away from the cutting means at all times, especially when turning on the motor. WARNING: Consider the environment in which you are working. Keep the working area free from wires, sticks, stones, and debris, which if struck by the cutter can become thrown objects.
- Page 12 REPLACING THE TRI - ARC BLADE 1. Place the product on a level surface. Position the product with the motor side down and the safety guard side up. 2. Insert the lock pin into the slot underneath the trimmer head. Loosen the nut by turning it clockwise using the combination wrench.
- Page 13 5. Insert the lock pin into the slot underneath the trimmer head. Tighten the nut by turning it counterclockwise using the combination wrench. 6. Remove the lock pin. Maintenance...
- Page 14 CLEANING THE PRODUCT 1. Place the product on a level surface. Position the product with the motor side down and the safety guard side up. WARNING: Exercise extreme caution when using the product. Keep hands and feet away from the cutting means at all times, especially when turning on the motor.
- Page 15 STORING THE PRODUCT WARNING: Clean the product before storing. 1. Install the blade protector. 2. Store the product in a cool, dry, and well-ventilated place that is inaccessible to children and away from sources of ignition. Do not store the product outdoors.
- Page 16 PRODUCT SPECIFICATIONS Low speed 5200 min Total weight 4.1 kg Brushcutter attachment Vibration level (in accordance with IEC 62841-1) Model REBCTA10 Front handle = 2.5 m/s Weight 1.5 kg Rear handle = 3.6 m/s Blade diameter 254 mm Uncertainty = 1.5 m/s...
- Page 17 TRI-ARC blade (26 cm) 638006025 Brushcutter blade PBB1 NOTE: Visit your local special orders desk or contact RYOBI customer service for replacement parts. WARNING! The declared vibration total values and the declared noise emission values given in this instruction manual have been measured in accordance with a standardised test and may be used to compare one tool with another.
- Page 20 Techtronic Industries N.Z. Limited Unit C, 70 Business Parade South, Highbrook, Auckland 2013, New Zealand RYOBI is a trade mark of Ryobi Limited, and is used under license. TRI-ARC is a trade mark of Techtronic Outdoor Products Technology Limited. 961479131-02...
Need help?
Do you have a question about the REBCTA10 and is the answer not in the manual?
Questions and answers