Page 2
Quick Start Guide Foreword General This manual introduces the functions, installation, and operations of the camera. Safety Instructions The following categorized signal words with defined meaning might appear in the manual. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, WARNING could result in slight or moderate injury.
Page 3
Quick Start Guide Please visit our website, contact the supplier or customer service if there is any problem occurred when using the device. If there is any uncertainty or controversy, please refer to our final explanation.
Page 4
Quick Start Guide Important Safeguards and Warnings Electrical Safety All installation and operation shall conform to your local electrical safety codes. The power source shall conform to the Safety Extra Low Voltage (SELV) standard, and supply power with rated voltage which conforms to Limited power Source requirement according to IEC60950-1.
Page 5
Quick Start Guide It is recommended to ground the device to enhance reliability. Do not touch the image sensor (CMOS) directly. Dust and dirt can be removed with air blower, or you can wipe the lens gently with soft cloth that is moistened with alcohol. You can clean the device body with soft dry cloth, and for stubborn stains, use the cloth with ...
Page 6
Quick Start Guide Table of Contents Foreword ..............................I Important Safeguards and Warnings ....................III 1 Introduction ............................1 Device Ports ..........................1 Connecting Alarm Input/output ..................... 2 2 Network Configuration.......................... 4 Initializing Device .......................... 4 Modifying Device IP Address ......................5 Logging in to Web Interface ......................
Page 7
Quick Start Guide Introduction Device Ports Figure 1-1 Device ports For more information about device ports, see Table 1-1. Table 1-1 Device ports information Port Name Description Connects to network with network cable. Provides power to the device with PoE. PoE is available on select models.
Page 8
Quick Start Guide Connecting Alarm Input/output Alarm input/output is available on select models. Step 1 Connect alarm input device to the alarm input end of the I/O port. See Figure 1-2. Device collects different states of alarm input port when the input signal is idling and grounded.
Page 9
Quick Start Guide The alarm input on the web interface is corresponding to the alarm input end of the I/O port. There will be high-level and low-level alarm signal generated by the alarm input device when alarm occurs. Set the input mode to "NO" (default) if the alarm input signal is logic "0"...
Page 10
Quick Start Guide Network Configuration Device initialization and IP address setting can be finished with the "ConfigTool" or on web interface. For more information, see the Web Operation Manual. Device initialization is required at first use or after the device being reset. ...
Page 11
Quick Start Guide Step 6 Select the devices that need initialization, and then click Initialize. The password setting interface is displayed. See Figure 2-2. Figure 2-2 Password setting Step 7 Set and confirm the password of the devices, then enter a valid email address, and then click Next.
Page 12
Quick Start Guide Step 2 Select the devices whose IP addresses need to be modified, and then click Modify IP. The Modify IP Address interface is displayed. See Figure 2-3. Figure 2-3 Modify IP Address Step 3 Select Static mode, and then enter start IP, subnet mask, and gateway. IP addresses of multiple devices will be set to the same if you select the Same IP ...
Page 13
Quick Start Guide Figure 2-4 Main interface...
Page 14
Quick Start Guide Installation Packing List The tool required for the installation such as electric drill is not provided in the packing. The operation manual and related tool information are contained in the QR code. Dimensions The following figures are for reference only, and the actual product shall prevail. Unit (mm [inch])
Page 15
Quick Start Guide Installing Device 3.3.1 Installation Type 3.3.2 Assembling Device 3.3.3 Installing SD Card (Optional) Disconnect the power before installing or removing the SD card. 3.3.4 Attaching Device...
Page 16
Quick Start Guide Make sure that the mounting surface is strong enough to hold at least three times of the weight of the device and bracket.
Need help?
Do you have a question about the IPC-K42P and is the answer not in the manual?
Questions and answers